In this paper, tungsten heavy alloys (THAs) were fabricated by laser direct deposition technology. The phase composition, microstructure and the influences of Fe and Co content on the properties of THAs were investigated. The results showed that the laser deposition layers were composed by W, Ni4W and Ni, fine and dense columnar crystals were distributed between non-melting W particles. The direction of crystals growth nearly paralleled the deposition direction at the bottom of deposition layers and nearly paralleled the scanning direction at the top. Both Fe and Co could increase the tensile strength of THAs and the elongation of W–Ni–Co alloys was higher than W–Ni–Fe alloys.
RabinB. H. and GermanR. M.: ‘Microstructure effects on tensile properties of tungsten-nickel-iron composites’, Metall. Mater. Trans. A, 1988, 19, (6), 1523–1532. doi: 10.1007/BF02674026
2.
CaiW. D., LiY., DowdingR. J., MohamedF. A. and LaverniaE. J.: ‘A review of tungsten-based alloys as kinetic energy penetrator materials’, Met. Powder Ind., 1995, 3, 71–131.
3.
EkbomL. B.: ‘Tungsten heavy metals’, Scand. J. Metall., 1991, 20, (3), 190–197.
4.
ZhangZ.-W., ZhouJ.-E., XiS.-Q., RanG. and LiP.-L.: ‘Phase transformation and thermal stability of mechanically alloyed W–Ni–Fe composite materials’, Mater. Sci. Eng. A – Struct., 2004, 379, (1), 148–153. doi: 10.1016/j.msea.2004.02.039
5.
ZhuY. B., WangY., ZhangX. Y. and QinG. W.: ‘W/NiFe phase interfacial characteristics of liquid-phase sintered W–Ni–Fe alloy’, Int. J. Refract. Met. H, 2007, 25, (4), 275–279. doi: 10.1016/j.ijrmhm.2006.08.003
6.
ChurnK. S. and GermanR. M.: ‘Fracture behavior of W-Ni-Fe heavy alloys’, Metall. Mater. Trans. A, 1984, 15, (2), 331–338. doi: 10.1007/BF02645119
7.
ZhangD. Q., LiuZ. H., CaiQ. Z., LiuJ. H. and ChuaC. K.: ‘Influence of Ni content on microstructure of W–Ni alloy produced by selective laser melting’, Int. J. Refract. Met. H, 2014, 45, 15–22. doi: 10.1016/j.ijrmhm.2014.02.007
8.
RaviG. A., HaoX. J., WainN., WuX. and AttallahM. M.: ‘Direct laser fabrication of three dimensional components using SC420 stainless steel’, Mater. Des., 2013, 47, 731–736. doi: 10.1016/j.matdes.2012.12.062
9.
MilewskiJ. O., LewisG. K., ThomaD. J., KeelG. I., NemecR. B. and ReinertR. A.: ‘Directed light fabrication of a solid metal hemisphere using 5-axis powder deposition’, J. Mater. Process. Technol., 1998, 75, 165–172. doi: 10.1016/S0924-0136(97)00321-X
10.
ZhongM., LiuW., NingG., YangL. and ChenY. X.: ‘Laser direct manufacturing of tungsten nickel collimation component’, Mater. Process. Technol., 2004, 147, 167–173. doi: 10.1016/j.jmatprotec.2003.12.009
11.
AtwoodC., GriBthM., HarwellL., SchliengerE., EnszM., SmugereskyJ., RomeroT., GreeneD. and ReckawayD.: ‘Laser engineered net shaping (LENS (TM)): A tool for direct fabrication of metal parts’, Proc. ICALEO, 1998, 98, 16–19.
12.
WuX.: ‘A review of laser fabrication of metallic engineering components and of materials’, Mater. Sci. Technol.-Lond., 2007, 23, (6), 631–640. doi: 10.1179/174328407X179593
13.
MaM., WangZ., WangD. and ZengX.: ‘Control of shape and performance for direct laser fabrication of precision large-scale metal parts with 316L Stainless Steel’, Opt. Laser Technol., 2013, 45, 209–216. doi: 10.1016/j.optlastec.2012.07.002
14.
LiP., YangT. P., LiS., LiuD. S., HuQ. W., XiongW. H. and ZengX. Y.: ‘Direct laser fabrication of nickel alloy samples’, Int. J. Mach. Tool Manuf., 2005, 45, (11), 1288–1294. doi: 10.1016/j.ijmachtools.2005.01.014
15.
DindaG. P., DasguptaA. K. and MazumderJ.: ‘Laser aided direct metal deposition of Inconel 625 superalloy: microstructural evolution and thermal stability’, Mater. Sci. Eng. A – Struct., 2009, 509, (1), 98–104. doi: 10.1016/j.msea.2009.01.009
16.
SextonL., LavinS., ByrneG. and KennedyA.: ‘Laser cladding of aerospace materials’, J. Mater. Process. Technol., 2002, 122, (1), 63–68. doi: 10.1016/S0924-0136(01)01121-9
17.
WangF., MeiJ. and WuX.: ‘Direct laser fabrication of Ti6Al4V/TiB’, J. Mater. Process. Technol., 2008, 195, (1), 321–326. doi: 10.1016/j.jmatprotec.2007.05.024
18.
WuX. and MeiJ.: ‘Near net shape manufacturing of components using direct laser fabrication technology’, J. Mater. Process. Technol., 2003, 135, (2), 266–270. doi: 10.1016/S0924-0136(02)00906-8
19.
UhlmannE., BergmannA. and GridinW.: ‘Investigation on additive manufacturing of tungsten carbide-cobalt by selective laser melting’, Procedia CIRP, 2015, 35, 8–15. doi: 10.1016/j.procir.2015.08.060
20.
ZhangD., CaiQ., LiuJ. and LiR.: ‘Research on process and microstructure formation of W-Ni-Fe alloy fabricated by selective laser melting’, J. Mater. Eng. Perform., 2011, 20, (6), 1049–1054. doi: 10.1007/s11665-010-9720-3
21.
H. Müller-Krumbhaar, W. Kurz and E. Brener: ‘Solidification’ in ‘Phase Transformations in Materials’, Vol. 100, Chap. 2 (ed. G. Kostorz), 2001, Weinheim, Wiley-VCH.
22.
YangS., LiuZ. X., LiuW. J., HuangW. D. and ZhouY. H.: ‘Two-dimensional numerical model of temperature field during laser surface remelting’, Appl. Laser, 2005, 25, (5), 313–315.
23.
RappazM., CarruptB., ZimmermannM. and KurzW.: ‘Numerical simulation of eutectic solidification in the laser treatment of materials’, Helv. Phys. Acta, 1987, 60, 924–936.
24.
RyuH. J., HongS. H. and BaekW. H.: ‘Microstructure and mechanical properties of mechanically alloyed and solid-state sintered tungsten heavy alloys’, Mater. Sci. Eng. A – Struct., 2000, 291, (1), 91–96. doi: 10.1016/S0921-5093(00)00968-0
25.
HongM. H., NohJ. W., KimE. P., SongH. S., LeeS. and BaekW. H.: ‘A study on the improvement of the sintered density of W-Ni-Mn heavy alloy’, Metall. Mater. Trans. B, 1997, 28, (5), 835–839. doi: 10.1007/s11663-997-0011-9
26.
ZhouG. A., LaiH. Y. and WuQ. L.: ‘The influence of Co and Mn on W-Ni-Fe alloys and their wetting mechanism’, Rare Met., 1987, 11, (5), 342–345.
27.
ZhouC., YiJ. and LuoS.: ‘Sintering high tungsten content W-Ni-Fe heavy alloys by microwave radiation’, Mater. Trans. A, 2014, 45, (1), 455–463. doi: 10.1007/s11661-013-1964-8
28.
DasJ., KiranU. R., ChakrabortyA. and PrasadN. E.: ‘Hardness and tensile properties of tungsten based heavy alloys prepared by liquid phase sintering technique’, Int. J. Refract. Met. H, 2009, 27, (3), 577–583. doi: 10.1016/j.ijrmhm.2008.08.003
29.
GermanR. M., HanafeeJ. E. and DiGiallonardoS. L.: ‘Toughness variation with test temperature and Cooling Rate for Liquid Phase Sintered W-3.5Ni-1.5Fe’, Metall. Mater. Trans. A, 1984, 15, (1), 121–128. doi: 10.1007/BF02644393
