The tensile flow behaviour of mechanically milled iron and a low-alloy steel are analysed using power law models that describe the evolution of stress–strain during a tensile test. A new analytical power law equation is presented that is shown to be superior to the Hollomon and Ludwigson equation to describe the room temperature flow properties of the low-alloy steel over a wide strain rate range. It not only provides a better fit to the homogenous flow curve of the low-alloy steel but also predicts the maximum strength without the prior knowledge of the uniform strain. The new equation also fitted the flow curves of mechanically milled iron with grain sizes in nano to micrometer range.
HallE. O.: ‘Yield point phenomena in metals and alloys', 1st edn, 3–59; 1970,
London, UK, Macmillan & Co Ltd.
2.
GuptaC. and MurtyK. L.: ‘Aging: dynamic strain, neutron irradiation effect’ in ‘Encyclopedia of iron, steel and their alloys', (eds. R. Colàs and G. E. Totten), 129–146; 2016, Boca Raton, FL, USA, CRC press.
3.
ChoudharyB. K., PalapartiD. P. R. and SamuelI.: ‘Analysis of tensile stress-strain and work hardening behaviour in 9 Cr-1Mo ferritic steel’, Metall. Mater. Trans., 2013, 44A, 212–223. doi: 10.1007/s11661-012-1385-0
4.
DieterG. E.: ‘Mechanical metallurgy’, 275–324; 1988,
London, UK, McGraw Hill Book Co.
5.
KocksU. and MeckingH.: ‘Physics and phenomenology of strain hardening: the FCC case’, Prog. Mater. Sci., 2003, 48, 171–273. doi: 10.1016/S0079-6425(02)00003-8
6.
ValievR. Z., IslamgalievR. K. and AlexandrovI. V.: ‘Bulk nanostructured materials from severe plastic deformation’, Prog. Mater. Sci., 2000, 45, 103–189. doi: 10.1016/S0079-6425(99)00007-9
7.
MishraN. S., MishraS. and RamaswamyV.: ‘Analysis of temperature dependence of strain hardening behaviour in high strength steel’, Metall. Trans., 1989, 20A, 2819–2829. doi: 10.1007/BF02670174
8.
SivaprasadP. V., VenugopalS. and VenkadesanS.: ‘Tensile flow and work hardening behaviour of Ti- modified austenitic stainless steel’, Metall. Mater. Trans., 1997, 28A, 171–178. doi: 10.1007/s11661-997-0092-8
9.
SivaprasadP. V., VenkadesanS. and VenugopalS.: ‘Applicability of Ludwigson equation for describing the tensile flow behaviour of warm rolled type 316 stainless steel’, Scr. Metall., 1996, 20, 603–604. doi: 10.1016/0036-9748(86)90474-6
10.
SamuelK. G.: ‘Limitations of Hollomon and Ludwigson stress-strain relations in assessing the strain hardening parameter’, J. Phys. D: Appl. Phys., 2006, 39, 203–212. doi: 10.1088/0022-3727/39/1/030
11.
XieB.-S., CaiQ.-W., YuW., CaoJ.-M. and YangY.-F.: ‘Effect of tempering temperature on resistance to deformation behaviour for low alloy carbon bainitic YP960 steels', Mater. Sci. Eng., 2014, A618, 586–595. doi: 10.1016/j.msea.2014.09.054
12.
XieB.-S., CaiQ.-W., YuW., XuS.-X., WangB.: ‘A flow stress model for high strength steels with Low carbon bainite Structure’, J. Iron. Steel. Int., 2016, 23, 372–379. doi: 10.1016/S1006-706X(16)30059-0
13.
ChoudharyB. K. and ChristopherJ.: ‘Tensile work hardening behavior of thin-section plate and thick-section tubeplate forging of 9Cr-1Mo steel in the framework of one-internal-variable Kocks–Mecking Approach’, Metall. Mater. Trans., 2013, 44A, 4968–4978. doi: 10.1007/s11661-013-1873-x
14.
SauzayM., KubinL. P.: ‘Scaling laws for dislocation microstructures in monotonic and cyclic deformation of fcc metals', Prog. Mater. Sci., 2011, 56, 725–784. doi: 10.1016/j.pmatsci.2011.01.006
15.
SanfieldS. and ZaiserM.: ‘Pattern formation in a minimal model of continuum dislocation plasticity’, Modell. Simul. Mater. Sci. Eng., 2015, 062005, 1–18.
16.
BrownL. M.: ‘Constant intermittent flow of dislocations: central problems in plasticity’, Mater. Sci. Technol., 2012, 28, 1209–1232. doi: 10.1179/174328412X13409726212768
17.
GuptaC., ChakravarttyJ. K. and BanerjeeS.: ‘Microstructure and dynamic strain aging phenomena in two structural steels', Mater. Sci. Technol., 2011, 27, 1007–1012. doi: 10.1179/026708310X12815992418418
18.
GuptaC., KumawatB. and ChakravarttyJ. K.: ‘Descriptors of temporal signatures of serrations in low alloy steel’, Mater. Sci. Eng., 2015, 620A, 407–410. doi: 10.1016/j.msea.2014.10.032
19.
TakakiS. and KimuraY.: ‘Ultra grain refining of iron using mechanical milling technique’, J. Jap. Soc. Pow. Met., 1999, 46, 1235–1240.
20.
SchneiderC. A., RasbandW. S. and EliceiriK. W.: ‘NIH image to ImageJ: 25 years of image analysis', Nat. Methods, 2012, 9, 671–675. doi: 10.1038/nmeth.2089
21.
MoréJ. J.: ‘The Levenberg-Marquardt algorithm: implementation and theory, numerical analysis’ in ‘Lecture notes in mathematics 630', (ed. G. A. Watson), 105-116; 1977, Berlin, Germany, Springer Berlin Heidelberg.
22.
NakashimaK., SuzukiM., FutamuraY., TsuchiyamaT. and TakaiS.: ‘Limit of dislocation density and dislocation strengthening in iron’, Mater. Sci. Forum, 2006, 503–504, 627–632. doi: 10.4028/www.scientific.net/MSF.503-504.627
23.
BaileyJ. E. and HirschP. B.: ‘The dislocation distribution, flow stress and stored energy in cold worked polycrystalline silver’, Philos. Mag., 1960, 5, 485–497. doi: 10.1080/14786436008238300
24.
GuitérrezI. and AaltunaM.: ‘Work hardening of ferrite and microstructure based modelling of its mechanical behaviour under tension’, Acta. Mater., 2008, 56, 4682–4690. doi: 10.1016/j.actamat.2008.05.023
25.
KamikawaN., SatoK., MiyamotoG., MuriyamaM., SekidoN., TsuzakiK. and FuruharaT.: ‘Stress–strain behaviour of ferrite and bainite with nanoprecipitation in low carbon steels', Acta Mater., 2015, 83, 383–396. doi: 10.1016/j.actamat.2014.10.010
26.
BhadeshiaH. K. D. H.: ‘Bainite in steels', 2nd edn, 129–187; 2001,
London, UK, Institute of Materials.
27.
GongW., TomotaY., HarjoS., SuY. H. and AizawaK.: ‘Effect of prior martensite on bainite transformation in nanobainite steel’, Acta Mater., 2015, 85, 243–249. doi: 10.1016/j.actamat.2014.11.029
28.
ZakeriniaH., KermanpurA. and NajafizadehA.: ‘The effect of bainite in producing nano/ultrafine grained steel by the martensite treatment’, Mater. Sci. Eng., 2011, 528A, 3562–3567. doi: 10.1016/j.msea.2011.01.067
