In this study, the commercially pure aluminium is roll bonded at ambient temperatures. The effect of surface roughness and roll speed on the bond strength is evaluated by using the lap shear test. It is observed that the bond strength increased considerably with increasing surface roughness. The deformation caused owing to scratch brushing changed the surface roughness profile, which is the salient reason for the bond strength variation. Continuous striations with peaks and valleys of small-scale heights are observed at lower roughness values. Increasing roughness has reformed them into discrete profile asperities with sharp tips, influencing localised junction formation. On the other hand, the roll velocity has shown hardly any effect on the roll bonding of aluminium. With thorough investigation, it was conclusively explained that the effective change in the bond strength was not appreciable with varying the roll speed, provided the roll bonding takes place at optimised surface roughness conditions.
MansouriHEghbaliBAfrandM.Producing multi-layer composite of stainless steel/aluminium/copper by accumulative roll bonding (ARB) process. J Manuf Process. 2019;46:298–303. doi:10.1016/j.jmapro.2019.08.025.
5.
PanDGaoKYuJ.Cold roll bonding of bimetallic sheets and strips. Mater Sci Technol. 1989;5:934–939. doi:10.1179/mst.1989.5.9.934.
6.
SaitoYUtsunomiyaHTsujiNNovel ultra-high straining process for bulk materials development of the accumulative roll-bonding (ARB) process. Acta Mater. 1999;47:579–583.
7.
RahmatabadiDHashemiRMohammadiBExperimental evaluation of the plane stress fracture toughness for ultra-fine grained aluminium specimens prepared by accumulative roll bonding process. Mater Sci Eng A. 2017;708:301–310.
8.
TayyebiMRahmatabadiDKarimiAInvestigation of annealing treatment on the interfacial and mechanical properties of Al5052/Cu multilayered composites subjected to ARB process. J Alloys Compd. 2021;871:159513, doi:10.1016/j.jallcom.2021.159513.
9.
El MahallawyNFathyAAbdelaziemWMicrostructure evolution and mechanical properties of Al/Al-12%Si multilayer processed by accumulative roll bonding (ARB). Mater Sci Eng A [Internet]. 2015;647:127–135. doi:10.1016/j.msea.2015.08.064.
10.
KhdairAIFathyA.Enhanced strength and ductility of Al-SiC nanocomposites synthesized by accumulative roll bonding. J Mater Res Technol. 2020;9:478–489. doi:10.1016/j.jmrt.2019.10.077.
11.
MelaibariAFathyAMansouriMExperimental and numerical investigation on strengthening mechanisms of nanostructured Al-SiC composites. J Alloys Compd. 2019;774:1123–1132. doi:10.1016/j.jallcom.2018.10.007.
12.
GholamiMDHashemiRSedighiM.The effect of temperature on the mechanical properties and forming limit diagram of aluminium strips fabricated by accumulative roll bonding process. J Mater Res Technol. 2020;9:1831–1846. doi:10.1016/j.jmrt.2019.12.016.
13.
TayyebiMRahmatabadiDAdhamiMInfluence of ARB technique on the microstructural, mechanical and fracture properties of the multilayered Al1050/Al5052 composite reinforced by SiC particles. J Mater Res Technol. 2019;8:4287–4301. doi:10.1016/j.jmrt.2019.07.039.
14.
MahallawyN ElFathyAHassanMEvaluation of mechanical properties and microstructure of Al/Al–12%Si multilayer via warm accumulative roll bonding process. J Compos Mater. 2017: 0021998317692141, doi:10.1177/0021998317692141.
15.
RahmatabadiDHashemiR.Experimental evaluation of forming limit diagram and mechanical properties of nano/ultra-fine grained aluminium strips fabricated by accumulative roll bonding. Int J Mater Res. 2017;108:1036–1044. doi:10.3139/146.111566.
16.
ElwanMFathyAWagihAFabrication and investigation on the properties of ilmenite (FeTiO3)-based Al composite by accumulative roll bonding. J Compos Mater. 2020;54:1259–1271.
17.
FathyAIbrahimDElkadyOEvaluation of mechanical properties of 1050-Al reinforced with SiC particles via accumulative roll bonding process. J Compos Mater. 2019;53:209–218.
18.
EizadjouMDanesh ManeshHJanghorbanK.Mechanism of warm and cold roll bonding of aluminium alloy strips. Mater Des. 2009;30:4156–4161. doi:10.1016/j.matdes.2009.04.036.
ZhaoDSYanJCWangCWInterfacial structure and mechanical properties of hot roll bonded joints between titanium alloy and stainless steel using copper interlayer. Sci Technol Weld Join. 2008;13:765–768.
21.
HanJNiuHLiSEffect of mechanical surface treatment on the bonding mechanism and properties of cold-rolled Cu/Al clad plate. Chinese J Mech Eng (English Ed). 2020;33; doi:10.1186/s10033-020-00483-x.
22.
ComynJ.Surface treatment and analysis for adhesive bonding. Int J Adhes Adhes. 1990;10:161–165.
23.
SchödelSHerrmannJMerkleinM.Investigation of different surface treatment parameters in the context of roll bonding processes. Procedia Manuf. 2019;29:600–607. doi:10.1016/j.promfg.2019.02.098.
24.
ZhangWApsEBayN. Cold welding – Experimental investigation of the surface preparation methods. 1997.
25.
ZhanyW.A numerical model for cold welding of metals. CIRP Ann. 1996;45(1):215–220.
26.
LiLNagaiKYinF.Progress in cold roll bonding of metals. Sci Technol Adv Mater. 2008;9:023001.
27.
MiyajimaYIguchiKOnakaSEffects of rolling reduction and strength of composed layers on bond strength of pure copper and aluminium alloy clad sheets fabricated by cold roll bonding. Adv Mater Sci Eng. 2014;2014:1–11.
28.
GuoXRenZMaXEffect of temperature and reduction ratio on the interface bonding properties of TC4/304 plates manufactured by EA rolling. J Manuf Process. 2021;64:664–673. doi:10.1016/j.jmapro.2021.02.006.
29.
YanHLenardJG.A study of warm and cold roll-bonding of an aluminium alloy. Mater Sci Eng A. 2004;385:419–428.
30.
MilnerDRVaidyanathLR.Significance of surface preparation in cold pressure welding. Met Constr Br Weld J. 1960;7:1–6.
31.
PerspectivesF. Roll bonding processes: state-of-the-art and future perspectives. 2021.
32.
SteinlageGABowmanKJTrumbleKP.A comparison of three mechanical models for cold roll bonding metal laminates. J Adhes Sci Technol. 1996;10:199–229.
33.
JamaatiRToroghinejadMR.Investigation of the parameters of the cold roll bonding (CRB) process. Mater Sci Eng A. 2010;527:2320–2326.
34.
McBrideBNLClarkeKDClarkeAJ.Mitigation of edge cracking during accumulative roll bonding (ARB) of aluminium strips. J Manuf Process. 2020;55:236–239. doi:10.1016/j.jmapro.2020.03.042.
35.
NaseriMReihanianMBorhaniE.Bonding behavior during cold roll-cladding of tri-layered Al / brass / Al composite. J Manuf Process. 2016;24:125–137. doi:10.1016/j.jmapro.2016.08.008.
36.
QuadirMZWolzAHoffmanMInfluence of processing parameters on the bond toughness of roll-bonded aluminium strip. Scr Mater. 2008;58:959–962.
37.
Vini MHSedighiM.Mechanical properties and bond strength of bimetallic AA1050/AA5083 laminates fabricated by warm-accumulative roll bonding. Can Metall Q. 2018;57:160–167. doi:10.1080/00084433.2017.1405539.
38.
MukaeSNishioKKatoMEffect of heat treatment on bond characteristics of aluminium clad steel: production and characteristics of vacuum roll bonded clad materials (2nd report). Weld Int. 1995;9:384–389.
39.
BuchnerMBuchnerBBuchmayrBInvestigation of different parameters on roll bonding quality of aluminium and steel sheets. Int J Mater Form. 2008;1:1279–1282.
40.
JamaatiRToroghinejadMR.The role of surface preparation parameters on cold roll bonding of aluminium strips. J Mater Eng Perform. 2011;20:191–197.
41.
HirschJ.Annealing of Aluminum and Its Alloys, Heat Treating of Nonferrous Alloys. Vol. 4E. Materials Park, Ohio: ASM International; 2016. doi:10.31399/asm.hb.v04e.a0006285.
42.
MilnerDRRoweGW.Fundamentals of solid phase welding. Mtlr. 1962;7:433–479.
43.
MohamedHAWashburnJ.Mechanism of solid state pressure welding. Weld J (Miami, Fla). 1975;54:302–310.
44.
BaranGR.The metallurgy of Ni-Cr alloys for fixed prosthodontics. J Prosthet Dent. 1983;50:639–650.
45.
WrightKPSnowADTayKC.Interfacial conditions and bond strength in cold pressure welding by rolling. Met Technol. 1978;5:24–31.
46.
GuoHHuJTsaiHL.Numerical modeling of cold weld formation and improvement in gmaw of aluminium alloys. Numer Heat Transf Part A Appl. 2010;57:392–414.
47.
GuoDZhengZLiSBonding process and mechanisms of interface evolution of stainless steel clad plates fabricated by cyclic phase transformation heat treatment. J Adhes Sci Technol. 2021;0:1–16. doi:10.1080/01694243.2021.1952013.
48.
BowdenFPTaborD.The friction and lubrication of solids. New York, 10016 USA: Oxford University Press; 2001.
49.
TangCLiuZZhouDSurface treatment with the cold roll bonding process for an aluminum alloy and mild steel. Strength Mater. 2015;47:150–155.
50.
GaoCLiLChenXThe effect of surface preparation on the bond strength of Al-St strips in CRB process. Mater Des. 2016;107:205–211. doi:10.1016/j.matdes.2016.05.112.
51.
SaranamVRMullanyBTabeiASurface topographical effects in the diffusion bonding of 316 stainless steel. J Mater Process Technol. 2021;296:117173, doi:10.1016/j.jmatprotec.2021.117173.
52.
ReviewedPBerkeleyLCancerB. Lawrence Berkeley National Laboratory Lawrence Berkeley National Laboratory. 2010;35–43.
53.
JamaatiRToroghinejadMRJamaatiRThe role of surface preparation parameters on cold roll bonding of aluminum stripsJ Mater Eng Perform. 2011;20:191–197.
54.
TorranceAA.Using profilometry for the quantitative assessment of tribological function: PC-based software for friction and wear prediction. Wear. 1995;181–183:397–404.
55.
BowdenFP.TaborD.The Friction and Lubrication of Solids. 1950;19(7):428–429.
56.
BowdenFPRoweGW.The adhesion of clean metals. Proc R Soc London Ser A Math Phys Sci. 1956;233:429–442.
57.
WangBHuWKongLXThe influence of roll speed on the rolling of metal plates. Met Mater Int. 1998;4:915–919.
58.
D K. FEM analysis of effect of rolling parameters on cold rolling process. Bonfring Int J Ind Eng Manag Sci. 2012;2:35–40.
