Downhole drilling motor is one of the equipment used for drilling and they perform the task of directional drilling. The rotor of these motors is made of 17-4 PH steel, which is generally coated with hard chromium. In this study, the feasibility of replacing hard chromium with WC–20Co–1Ni using a high velocity oxygen fuel system was examined. The result of the metallurgical and mechanical examination showed that changing of the coating to WC–20Co–1Ni improved the wear performance and increased the lifespan of the rotor. In addition, the chemical resistance to corrosion due to the influence of the corrosive gases in the hole on the rotor improved significantly. Finally, substitution of the hard chromium coating with the WC–20Co–1Ni caused an increase in the lifespan and performance of the downhole motor in extreme environmental conditions of the drilling formations, which led to economic savings in amendment and maintenance costs.
MillsRAR, GaymardR. New application for wellbore progressing cavity pumps. Mexico
: Society of Petroleum Engineers; 1996.
2.
ParkRM, BenaJF, StaynerLT, Hexavalent chromium and lung cancer in the chromate industry: a quantitative risk assessment. Risk Anal. 2004;24(5):1099–1108. doi: 10.1111/j.0272-4332.2004.00512.x
3.
Occupational exposure to hexavalent chromium. Atlanta
: DHHS (NIOSH) Publication; 2006.
4.
Off J Eur Union. 2000;269:34.
5.
YinKM, WangCM. A study on the deposit uniformity of hard chromium plating on the interior of small-diameter tubes. Surf Coat Technol. 1999;114:213–223. doi: 10.1016/S0257-8972(99)00046-8
BrondelD, EdwardsR, HaymanA, Corrosion in the oil industry. Oilfield Rev. 1994;6(2):4–18.
8.
PeatT, GallowayAM, ToumpisAI, Evaluation of the synergistic erosion-corrosion behaviour of HVOF thermal spray coatings. Surf Coat Technol. 2016;299:37–48. doi: 10.1016/j.surfcoat.2016.04.072
9.
RanjbarKh, SababiM. Failure assessment of the hard chrome coated rotors in the downhole drilling motors. Eng Fail Anal. 2012;20:147–155. doi: 10.1016/j.engfailanal.2011.11.007
10.
BolelliG, GiovanardiR, LusvarghiL, Corrosion resistance of HVOF-sprayed coatings for hard chrome replacement. Corros Sci. 2006;48:3375–3397. doi: 10.1016/j.corsci.2006.03.001
11.
BolelliG, CannilloV, LusvarghiL, Mechanical and tribological properties of electrolytic hard chrome and HVOF-sprayed coatings. Surf Coat Technol. 2006;200:2995–3009. doi: 10.1016/j.surfcoat.2005.04.057
12.
PicasJA, RupérezE, PunsetM, Influence of HVOF spraying parameters on the corrosion resistance of WC–CoCr coatings in strong acidic environment. Surf Coat Technol. 2013;225:47–57. doi: 10.1016/j.surfcoat.2013.03.015
13.
HouGL, ZhouHD, AnYL, Microstructure and high-temperature friction and wear behavior of WC-(W,Cr)2C-Ni coating prepared by high velocity oxy-fuel spraying. Surf Coat Technol. 2011;206:82–94. doi: 10.1016/j.surfcoat.2011.06.047
14.
WangQ, ZhangSh, ChengY, Wear and corrosion performance of WC-10Co4Cr coatings deposited by different HVOF and HVAF spraying processes. Surf Coat Technol. 2013;218:127–136. doi: 10.1016/j.surfcoat.2012.12.041
15.
SartwellB, LeggK, SauerJ. Environmental Security Technology Certification Program (ESTCP) and Joint Group on Pollution Prevention (JG-PP), 2004.
16.
MoignA, VardelleA, LegouxJG, LCA comparison of electroplating and other thermal spray processes. Proceedings of the International Thermal Spray Conference, Thermal Spray, 2009, paper 1207–1212.
17.
HsiaoCN, ChiouCS, YongJR. Aging reactions in a 17-4 PH stainless steel. Mater Chem Phys. 2002;74:134–142. doi: 10.1016/S0254-0584(01)00460-6
18.
BressanJD, DarosDP, SokolowskiA, Influence of hardness on the wear resistance of 17-4 PH stainless steel evaluated by the pin-on-disc testing. J Mater Process Technol. 2008;205:353–359. doi: 10.1016/j.jmatprotec.2007.11.251
19.
LeggKO, GrahamM, ChangP, The replacement of electroplating, surface and coating technology. 1996;81(1):99–105.
20.
LeggKO. Overview of chromium and cadmium alternative technologies. Surface Modification Technologies XV, Proceedings of the International Conference on Surface Modification Technologies, 15th, Ohio, USA. Ohio and IOM Communications Ltd.; 2002. Paper 235–244.
21.
FischerF, DvorakM, SiegmannSt. Development of ultra thin carbide coatings for wear and corrosion resistance. New Surfaces for a New Millenium, Proceedings of the International Thermal Spray Conference, Ohio, USA. Ohio and IOM Communications Ltd.; 2002. Paper 1131–1135.
22.
HuangCA, LiuYW, YuC, Role of carbon in the chromium deposit electroplated from a trivalent chromium-based bath. Surf Coat Technol. 2011;205:3461–3466. doi: 10.1016/j.surfcoat.2010.12.010
23.
KsiazekM, BoronL, RadeckaM, The structure and bond strength of composite carbide coatings (WC-Co + Ni) deposited on ductile cast iron by Thermal Spraying. JMEPEG. 2016;25:502–509. doi: 10.1007/s11665-015-1871-9
24.
GuilemanyJM, de PacoJM, NuttingJ, Characterization of W2C phase formed during the high velocity oxygen fuel spraying of a WC + 12 Pct Co powder. Metal Mater Trans. 1913;1999:30A–1921.
25.
QiY, LuoH, ZhengSh, Effect of temperature on the corrosion behavior of carbon steel in hydrogen sulphide environments. Int J Electrochem Sci. 2014;9:2101–2112.
