Fitting experimentally measured Raman bands with theoretical model profiles is the basic operation for numerical determination of Raman peak parameters. In order to investigate the effects of peak modeling using various algorithms on peak fitting results, the representative Raman bands of mineral crystals, glass, fluids as well as the emission lines from a fluorescent lamp, some of which were measured under ambient light whereas others under elevated pressure and temperature conditions, were fitted using Gaussian, Lorentzian, Gaussian–Lorentzian, Voigtian, Pearson type IV, and beta profiles. From the fitting results of the Raman bands investigated in this study, the fitted peak position, intensity, area and full width at half-maximum (FWHM) values of the measured Raman bands can vary significantly depending upon which peak profile function is used in the fitting, and the most appropriate fitting profile should be selected depending upon the nature of the Raman bands. Specifically, the symmetric Raman bands of mineral crystals and non-aqueous fluids are best fit using Gaussian–Lorentzian or Voigtian profiles, whereas the asymmetric Raman bands are best fit using Pearson type IV profiles. The asymmetric O–H stretching vibrations of H2O and the Raman bands of soda–lime glass are best fit using several Gaussian profiles, whereas the emission lines from a florescent light are best fit using beta profiles. Multiple peaks that are not clearly separated can be fit simultaneously, provided the residuals in the fitting of one peak will not affect the fitting of the remaining peaks to a significant degree. Once the resolution of the Raman spectrometer has been properly accounted for, our findings show that the precision in peak position and intensity can be improved significantly by fitting the measured Raman peaks with appropriate profiles. Nevertheless, significant errors in peak position and intensity were still observed in the results from fitting of weak and wide Raman bands having unnormalized intensity/FWHM ratios lower than 200 counts/cm−1.
FrezzottiM.L.TecceF.CasagliA.“Raman Spectroscopy for Fluid Inclusion Analysis”. J. Geochem. Explor2012; 112: 1–20.
5.
KiefertL.KarampelasS.“Use of the Raman Spectrometer in Gemological Laboratories: Review”. Spectrochim. Acta, Part A2011; 80(1): 119–124.
6.
LiY.S.ChurchJ.S.“Raman Spectroscopy in the Analysis of Food and Pharmaceutical Nanomaterials”. J. Food Drug Anal2014; 22(1): 29–48.
7.
PiscanecaS.FerrariA.C.CantoroM.HofmannS., et al.“Raman Spectrum of Silicon Nanowires”. Mater. Sci. Eng., C2003; 23: 931–934.
8.
YangD.YingY.“Applications of Raman Spectroscopy in Agricultural Products and Food Analysis: A Review”. Appl. Spectrosc. Rev2011; 46(7): 536–560.
9.
ZhangX.KirkwoodW.J.WalzP.M.PeltzerE.T., et al.“A Review of Advances in Deep-Ocean Raman Spectroscopy”. Appl. Spectrosc2012; 66(3): 237–249.
10.
FabreD.OksengornB.“Pressure and Density Dependence of the CH4 and N2 Raman Lines in an Equimolar CH4/N2 Gas Mixture”. Appl. Spectrosc1992; 46(3): 468–471.
11.
KawakamiY.YamamotoJ.KagiH.“Micro-Raman Densimeter for CO2 Inclusions in Mantle-Derived Minerals”. Appl. Spectrosc2003; 57(11): 1333–1339.
12.
LinF.BodnarR.J.BeckerS.P.“Experimental Determination of the Raman CH4 Symmetric Stretching (ν1) Band Position from 1–650 bar and 0.3–22 ℃: Application to Fluid Inclusion Studies”. Geochim. Cosmochim. Acta2007; 71(15): 3746–3756.
13.
LuW.ChouI.M.BurrussR.C.SongY.“A Unified Equation for Calculating Methane Vapor Pressures in the CH4–H2O System with Measured Raman Shifts”. Geochim. Cosmochim. Acta2007; 71(16): 3969–3978.
14.
RossoK.M.BodnarR.J.“Microthermometric and Raman Spectroscopic Detection Limits of CO2 in Fluid Inclusions and the Raman Spectroscopic Characterization of CO2”. Geochim. Cosmochim. Acta1995; 59(19): 3961–3975.
15.
SeitzJ.C.PasterisJ.D.ChouI.M.“Raman Spectroscopic Characterization of Gas Mixtures. II. Quantitative Composition and Pressure Determination of the CO2–CH4 System”. Am. J. Sci1996; 296(6): 577–600.
16.
SongY.ChouI.M.HuW.RobertB., et al.“CO2 Density-Raman Shift Relation Derived from Synthetic Inclusions in Fused Silica Capillaries and Its Application”. Acta Geol. Sin. (Engl. Ed.)2009; 83(5): 932–938.
17.
WangX.ChouI.M.HuW.BurrussR.C., et al.“Raman Spectroscopic Measurements of CO2 Density: Experimental Calibration with High-Pressure Optical Cell (HPOC) and Fused Silica Capillary Capsule (FSCC) with Application to Fluid Inclusion Observations”. Geochim. Cosmochim. Acta2011; 75(14): 4080–4093.
18.
YamamotoJ.KagiH.“Extended Micro-Raman Densimeter for CO2 Applicable to Mantle-Originated Fluid Inclusions”. Chem. Lett2006; 35(6): 610–611.
19.
DatchiF.CannyB.“Raman Spectrum of Cubic Boron Nitride at High Pressure and Temperature”. Phys. Rev. B2004; 69(14): 144106.
20.
KawamotoT.MatsukageK.N.NagaiT.NishimuraK., et al.“Raman Spectroscopy of Cubic Boron Nitride under High Temperature and Pressure Conditions: A New Optical Pressure Marker”. Rev. Sci. Instrum2004; 75(7): 2451–2454.
21.
SchmidtC.SteelemacinnisM.WatenphulA.WilkeM.“Calibration of Zircon as a Raman Spectroscopic Pressure Sensor to High Temperatures and Application to Water-Silicate Melt Systems”. Am. Mineral2013; 98(4): 643–650.
22.
SchmidtC.ZiemannM.A.“In-Situ Raman Spectroscopy of Quartz: A Pressure Sensor for Hydrothermal Diamond-Anvil Cell Experiments at Elevated Temperatures”. Am. Mineral2000; 85(11–12): 1725–1734.
23.
YangY.ZhengH.“Research on Raman Spectra of Anhydrite at Pressure of 0.1–1300 MPa and Room Temperature”. Kuangwu Xuebao [Acta Mineralogica Sinica]2005; 25(3): 4.
24.
YuanX.MayanovicR.A.ZhengH.“Determination of Pressure from Measured Raman Frequency Shifts of Anhydrite and its Application in Fluid Inclusions and HDAC Experiments”. Geochim. Cosmochim. Acta2016; 194: 253–265.
25.
ZhengH.QiaoE.YangY.DuanT.“Determination of Inner Pressure for Fluid Inclusions by Raman Spectroscopy and Its Application”. Coord. Chem. Rev2011; 2(3): 403–407.
26.
CaumonM.C.RobertP.LaverretE.TarantolaA., et al.“Determination of Methane Content in NaCl–H2O Fluid Inclusions by Raman Spectroscopy. Calibration and Application to the External Part of the Central Alps (Switzerland)”. Chem. Geol2014; 378–379: 52–61.
27.
DubessyJ.LhommeT.BoironM.RullF.“Determination of Chlorinity in Aqueous Fluids Using Raman Spectroscopy of the Stretching Band of Water at Room Temperature: Application to Fluid Inclusions”. Appl. Spectrosc2002; 56(1): 99–106.
28.
FrantzJ.D.“Raman Spectra of Potassium Carbonate and Bicarbonate Aqueous Fluids at Elevated Temperatures and Pressures: Comparison with Theoretical Simulations”. Chem. Geol1998; 152(3): 211–225.
29.
GuoH.ChenY.HuQ.LuW., et al.“Quantitative Raman Spectroscopic Investigation of Geo-Fluids High-Pressure Phase Equilibria: Part I. Accurate Calibration and Determination of CO2 Solubility in Water from 273.15 to 573.15 K and from 10 to 120 MPa”. Fluid Phase Equilib2014; 382: 70–79.
30.
KatoT.UmemuraJ.TakenakaT.“Raman Spectral Studies of Ionic Motion and Ionic Interaction in Aqueous Nitrate Solutions”. Mol. Phys2006; 36(3): 621–639.
31.
MernaghT.P.WildeA.R.“The Use of the Laser Raman Microprobe for the Determination of Salinity in Fluid Inclusions”. Geochim. Cosmochim. Acta1989; 53(4): 765–771.
32.
SunQ.ZhaoL.LiN.LiuJ.“Raman Spectroscopic Study for the Determination of Cl− Concentration (Molarity Scale) in Aqueous Solutions: Application to Fluid Inclusions”. Chem. Geol2010; 272(1): 55–61.
33.
WangX.HuW.ChouI.M.“Raman Spectroscopic Characterization on the OH Stretching Bands in NaCl-Na2CO3-Na2SO4-CO2-H2O Systems: Implications for the Measurement of Chloride Concentrations in Fluid Inclusions”. J. Geochem. Explor2013; 132: 111–119.
34.
WhiteS.N.“Qualitative and Quantitative Analysis of CO2 and CH4 Dissolved in Water and Seawater Using Laser Raman Spectroscopy”. Appl. Spectrosc2010; 64(7): 819–827.
35.
WuJ.ZhengH.“Quantitative Measurement of the Concentration of Sodium Carbonate in the System of Na2CO3–H2O by Raman Spectroscopy”. Chem. Geol2010; 273: 267–271.
36.
HesseR.ChasseT.SzarganR.“Peak Shape Analysis of Core Level Photoelectron Spectra Using Unifit for Windows”. Fresenius J. Anal. Chem1999; 365: 48–54.
37.
MysenB.O.FingerL.W.VirgoD.SeifertF.“Curve-Fitting of Raman Spectra of Silicate Glasses”. Am. Mineral1982; 67: 686–695.
38.
PeachG.“Theory of the Pressure Broadening and Shift of Spectral Lines”. Adv. Phys1981; 30(3): 367–474.
39.
RoccoH.O.D.CruzadoA.“The Voigt Profile as a Sum of a Gaussian and a Lorentzian Functions, When the Weight Coefficient Depends Only on the Widths Ratio”. Acta Phys. Pol., A2012; 122(4): 666–669.
40.
Van RegemorterH.“Spectral Line Broadening”. Annu. Rev. Astron. Astrophys2003; 3(1): 71–92.
41.
WertheimG.K.ButlerM.A.WestK.W.BuchananD.N.E.“Determination of the Gaussian and Lorentzian Content of Experimental Line Shapes”. Rev. Sci. Instrum1974; 45(11): 1369–1371.
42.
SundiusT.“Computer Fitting of Voigt Profiles to Raman Lines”. J. Raman Spectrosc1973; 1(5): 471–488.
43.
R.C.H. Cheng. “Using Pearson Type IV and Other Cinderella Distributions in Simulation”. In: Proceedings of the 2011 Winter Simulation Conference. Phoenix, AZ: 11–14 December 2011. doi: 10.1109/WSC.2011.6147775.
44.
BassettW.A.ShenA.H.BucknumM.ChouI.M.“A New Diamond Anvil Cell for Hydrothermal Studies to 2.5 GPa and from −190 to 1200 ℃”. Rev. Sci. Instrum1993; 64(8): 2340–2345.
45.
YuanX.MayanovicR.A.ZhengH.SunQ.“Determination of Pressure in Aqueo-Carbonic Fluid Inclusions at High Temperatures from Measured Raman Frequency Shifts of CO2”. Am. Mineral2017; 102: 404–411.
46.
GautamR.VangaS.ArieseF.UmapathyS.“Review of Multidimensional Data Processing Approaches for Raman and Infrared Spectroscopy”. EPJ Techniques and Instrumentation2015; 2: 8.
47.
CareyD.M.KorenowskiG.M.“Measurement of the Raman Spectrum of Liquid water”. J. Chem. Phys1998; 108: 2669–2675.
48.
GraenerH.“Anharmonicity and Overtone Spectra of OH Stretching Vibrations”. J. Phys. Chem1991; 95(9): 3450–3453.
49.
KawamotoT.OchiaiS.KagiH.“Changes in the Structure of Water Deduced from the Pressure Dependence of the Raman OH Frequency”. J. Chem. Phys2004; 120(13): 5867–5870.
SunQ.QinC.“Raman OH Stretching Band of Water as an Internal Standard to Determine Carbonate Concentrations”. Chem. Geol2011; 283(3): 274–278.
52.
WalrafenG.E.“Raman Spectral Studies of Water Structure”. J. Chem. Phys1964; 40(11): 3249–3256.
53.
FukuraS.MizukamiT.OdakeS.KagiH.“Factors Determining the Stability, Resolution, and Precision of a Conventional Raman Spectrometer”. Appl. Spectrosc2006; 60(8): 946–950.
