Effects of Handle Angle and Work Orientation on Hammering: I. Wrist Motion and Hammering Performance

Abstract

This research investigated the range of wrist motion characteristics associated with the ergonomic principle of “bending the tool and not the wrist” as applied to the hammer. It is thought that bending the tool reduces angular wrist motion, which has been shown in the literature to be a risk factor in hand/wrist disorders such as carpal tunnel syndrome and tenosynovitis. Hammer handles angled at 0 (straight), 20, and 40 deg were investigated in this study. For novices, hammer handles bent at 20 and 40 deg resulted in less total ulnar deviation than straight hammers. However, there was a trade-off in beginning and ending positions of the wrist in that the angled hammers reduced ulnar deviation at the impact position but increased radial deviation at the starting position of a hammer stroke. Handle angle did not significantly affect hammering performance. Wrist motion was affected minimally by hammering orientation, but hammering performance was significantly worse in the wall orientation compared with the bench orientation. This research suggests that for novice users, hammers with handles bent in the range of 20 to 40 deg could possibly decrease the incidence of hand/wrist disorders caused by hammering.

Get full access to this article

View all access options for this article.

References

An, K. N. , Askew, L. J. , and Chao, E. Y. (1986). Biomechanics and functional assessment of upper extremities. In Trends in ergonomics/human factors III (pp. 573–580). Amsterdam: Elsevier.

Armstrong, T. J. (1983). An ergonomics guide to carpal tunnel syndrome. In Ergonomics guides. Akron, OH: American Industrial Hygiene Association.

Armstrong, T. J. , Foulke, J. A. , Joseph, B. S. , and Goldstein, S. A. (1982). Investigation of cumulative trauma disorders in a poultry processing plant. American Industrial Hygiene Association Journal, 43(2), 103–116.

Caillet, R. (1984). Hand pain and impairment. Philadelphia: F. A. Davis Co.

Capenar, N. (1956). The hand in surgery. Journal of Bone and Joint Surgery, 3B(1), 128–151.

Chaffin, D. B. , and Andersson, G. B. J. (1984). Occupational biomechanics. New York: Wiley.

Damon, F. (1965). The use of biomechanics in manufacturing operations. The Western Electric Engineer, 9(4), 11–19.

Greenberg, L. , and Chaffin, D. B. (1977). Workers and their tools. Midland, MI: Pendell Publishing.

Hagberg, M. (1981). Electromyographic signs of shoulder muscular fatigue in two elevated arm postures. American Journal of Physical Medicine, 60(3), 111–121.

10.

Knowlton, R. G. , and Gilbert, J. C. (1983). Ulnar deviation and short-term strength reductions as affected by a curve-handled ripping hammer and a conventional claw hammer. Ergonomics, 26(2), 173–179.

11.

Konz, S. (1986). Bent hammer handles. Human Factors, 28, 317–323.

12.

Konz, S. , and Streets, B. (1984). Bent hammer handles: Performance and preference. In Proceedings of the Human Factors Society 28th Annual Meeting (pp. 438–440). Santa Monica, CA: Human Factors Society.

13.

Marras, W. S. , and Lavender, S. A. (1988). Analysis of hand tool injuries in the underground mine industry (Final Report, Contract No. J0348043). Pittsburgh, PA: U.S. Bureau of Mines.

14.

Marras, W. S. , and Rockwell, T. H. (1986). An experimental evaluation of method and tool effects in spike maul use. Human Factors, 28, 267–281.

15.

Meagher, S. W. (1986). Handtools: Cumulative trauma disorders caused by improper use of design elements. In Trends in ergonomics/human factors III (pp. 581–587). Amsterdam: Elsevier.

16.

Ohio Industrial Commission. (1984-1986). Injuries to carpenters/woodworkers caused by hammer. (Available from the Research and Statistics Section, Division of Safety and Hygiene, Ohio Industrial Commission, Columbus, OH.)

17.

Ohio Industrial Commission. (1985). Carpenter (census occupational code 567) 1985 injury/illness statistics. (Available from the Research and Statistics Section, Division of Safety and Hygiene, Ohio Industrial Commission, Columbus, OH.)

18.

Ohio Industrial Commission. (1986). Carpenters (census occupation code 567) 1986 injury/illness statistics. (Available from the Research and Statistics Section, Division of Safety and Hygiene, Ohio Industrial Commission, Columbus, OH.)

19.

Palmer, A. K. , Werner, F. W. , Murphy, D. M. , and Glisson, R. G. (1985). Functional wrist motion: A biomechanical study. Journal of Hand Surgery, 10A(1), 39–46.

20.

Schoenmarklin, R. W. , and Marras, W. S. (1987). Measurement of hand and wrist position by a wrist monitor. In Proceedings of the IX International Conference on Production Research (pp. 410–416). Amsterdam: Elsevier.

21.

Schoenmarklin, R. W. , and Marras, W. S. (1989). Effects of handle angle and work orientation in hammering: II. Muscle fatigue and subjective ratings of body discomfort. Human Factors, 31, 413–420.

22.

Tichauer, E. R. (1978). The biomechanical basis of ergonomics: Anatomy applied to the design of work stations. New York: Wiley.