To investigate the effects of incorporating gas and the associated influencing factors on polymer melt, a method of evaluating the gas-laden ability using modified rheometric measurements was proposed. In this study, common and widely used thermoplastic materials—polypropylene (PP) and high-density polyethylene (HDPE), and their blends with different weight ratios—were selected, and the rheological properties of neat melt and gas-laden melts were tested using a modified torque rheometer. The foamed samples were also produced using a regular injection-molding machine, and the foamed morphology was examined by scanning electron microscope (SEM). The comparison of rheological curves of neat melt and gas-laden melt indicated that the incorporation of gas influenced the rheological properties of the gas-laden polymer melts as evidenced by a decrease of zero-rotational torque and an increase in the melt flow index. The results also suggested that the gas-laden ability of polymer melt could be evaluated quantitatively by the decay (due to desorption) of gas using the modified rheological measurement method. This study also demonstrated that the gas-laden ability can be used to predict the foaming behavior of polymer melts.
SauceauMFagesJCommonA, et al. New challenges in polymer foaming: a review of extrusion processes assisted by supercritical carbon dioxide. Prog Polym Sci2011; 36: 749–766.
LeungSNWongAWangLC, et al. Mechanism of extensional stress-induced cell formation in polymeric foaming processes with the presence of nucleating agents. J Supercrit Fluid2012; 63: 187–198.
5.
RizviATabatabaeiABarzegariMR, et al. In situ fibrillation of CO2-philic polymers sustainable route to polymer foams in a continuous process. Polymer2013; 54: 4645–4652.
6.
HouJZhaoGWangG, et al. A novel gas-assisted microcellular injection molding method for preparing lightweight foams with superior surface appearance and enhanced mechanical performance. Mater Des2017; 127: 115–125.
7.
ZhouYGSuBTurngLS.Influence of processing conditions on morphological structure and ductility of water-foamed injection molded PP/LDPE blended parts. Cell Polym2017; 36: 51–74.
8.
VolpeVDe FilittoMKlofacovaV, et al. Effect of mold opening on the properties of PLA samples obtained by foam injection molding. Polym Eng Sci2018; 58: 475–484.
9.
ZhouYGSuBTurngLS.Mechanical properties, fiber orientation, and length distribution of glass fiber-reinforced polypropylene parts: influence of water-foaming technology. Polym Compos2018; 39: 4386–4399.
10.
EllinghamTKharbasHManitiuM, et al. Microcellular injection molding process for producing lightweight thermoplastic polyurethane with customizable properties. Front Mech Eng2018; 13: 96–106.
11.
TanXTZhouYGZhouJJ, et al. Effect of acrylonitrile-butadiene-styrene terpolymer on the foaming behavior of polypropylene. Cell Polym2019; 38: 47–67.
12.
TrommMShaayeganVWangC, et al. Investigation of the mold-filling phenomenon in high-pressure foam injection molding and its effects on the cellular structure in expanded foams. Polymer2019; 160: 43–52.
13.
HuangPWuFPangY, et al. Enhanced dispersion, flame retardancy and mechanical properties of polypropylene/intumescent flame retardant composites via supercritical CO2 foaming followed by defoaming. Compos Sci Technol2019; 171: 282–290.
14.
MohamadiMPapilaMGarmabiH, et al. Morphological evaluation and phase behavior of PVDF/PEO blends in the presence of graphene nanoplatelets through rheological measurements. J Appl Polym Sci2019; 136: 48017.
15.
XuMChenYLiuT, et al. Determination of modified polyamide 6's foaming windows by bubble growth simulations based on rheological measurements. J Appl Polym Sci2019; 136: 48138.
16.
SinhaVAhmedRAkhtarT, et al. Rheology and hydraulics of polymer-based foams at elevated temperatures. J Petrol Sci Eng2019; 180: 330–346.
17.
WeiTJinKTorkelsonJM.Isolating the effect of polymer-grafted nanoparticle interactions with matrix polymer from dispersion on composite property enhancement: the example of polypropylene/halloysite nanocomposites. Polymer2019; 176: 38–50.
18.
YuYSoukupZASarajiS.An experimental study of in-situ foam rheology: effect of stabilizing and destabilizing agents. Colloids Surf A2019; 578: 123548.
19.
ShiJFangXMaffeAP, et al. An effective method of processing immiscible polymer blends into strong fiber 2019; 59(10): 2052–2061.
20.
GahleitnerM.Melt rheology of polyolefins. Prog Polym Sci2001; 26: 895–944.
21.
SchrammG.A practical approach to rheology and rheometry. Karlsruhe, Germany: Gebrueder HAAKE GmbH, 2000.
22.
ParkHEDealyJM.Effects of pressure and supercritical fluids on the viscosity of polyethylene. Macromolecules2006; 39: 5438–5452.
23.
FangXYueXAFuJY, et al. Experimental study on factors affecting the end effect in gas viscosity measurement using capillary-tube viscometer. Rev Sci Instrum2019; 90: 074101.
24.
VincentRLanglotzMDüngenM.Viscosity measurement of polypropylene loaded with blowing agents (propane and carbon dioxide) by a novel inline method. J Cell Plast2020; 56: 73–88.
25.
RuedaMMAuscherMCFulchironR, et al. Rheology and applications of highly filled polymers: a review of current understanding. Prog Polym Sci2017; 66: 22–53.
26.
LeeMParkCBTzoganakisC.Measurements and modeling of PS/supercritical CO2 solution viscosities. Polym Eng Sci1999; 39: 99–109.
27.
LadinDParkCBParkSS, et al. Study of shear and extensional viscosities of biodegradable PBS/CO2 solutions. J Cell Plast2001; 37: 109–148.
28.
WangJJamesDFParkCB.Planar extensional flow resistance of a foaming plastic. J Rheol2010; 54: 95–116.
29.
GoodrichJEPorterRS.A rheological interpretation of torque-rheometer data. Polym Eng Sci1967; 7: 45–51.
30.
GoodrichJE.Torque rheometer evaluation of polypropylene process stability. Polym Eng Sci1970; 10: 215–221.
31.
DealyJMBroadheadTO.Process rheometers for molten plastics: a survey of existing technology. Polym Eng Sci1993; 33: 1513–1523.
32.
MarquezAQuijanoJGaulinM.A calibration technique to evaluate the power-law parameters of polymer melts using a torque-rheometer. Polym Eng Sci1996; 36: 2556–2563.
33.
ChengBZhouCYuW, et al. Evaluation of rheological parameters of polymer melts in torque rheometers. Polym Test2001; 20: 811–818.
34.
WangXYuWNieQ, et al. A real-time study on the evolution of the degradation of polypropylene during mixing process. J Appl Polym Sci2011; 121: 1220–1243.
35.
AbdoosHKhorsandHYousefiAA.Torque rheometry and rheological analysis of powder–polymer mixture for aluminum powder injection molding. Iran Polym J2014; 23: 745–755.
36.
CerauloMBottaLScaffaroR, et al. Prediction of the flow curves of thermoplastic polymer/clay systems from torque data. Polym Test2014; 37: 12–18.
37.
KöpplmayrTLugerH-JBurzicI, et al. A novel online rheometer for elongational viscosity measurement of polymer melts. Polym Test2016; 50: 208–215.
38.
Ait-KadiAMarchalPChoplinL, et al. Quantitative analysis of mixer-type rheometers using the couette analogy. Can J Chem Eng2002; 80: 1166–1174.
39.
ParlatoRMRussoERLaugerJ, et al. On the use of the coaxial cylinders equivalence for the measurement of viscosity in complex non-viscometric, rotational geometries.Fluids2020; 5: 43.
40.
CrankJ.The mathematics of diffusion. Oxford: Clarendon Press, 1975.
41.
StangeJMünstedtH.Rheological properties and foaming behavior of polypropylenes with different molecular structures. J Rheol2006; 50: 907–923.
42.
SunXKharbasHPengJ, et al. A novel method of producing lightweight microcellular injection molded parts with improved ductility and toughness. Polymer2015; 56: 102–110.
43.
Al-MullaAShabanH.Study on compatibility of recycled polypropylene/high density polyethylene blends using rheology. Polym Bull2014; 71: 2335–2352.
44.
KalikmanovVI. Nucleation theory. In: Citro R, Hänggi P, Hjorth-Jensen M, et al. (eds) Lecture notes in physics series. Berlin, Germany: Springer, 2013, p.860.
45.
ZhengWGLeeYHParkCB.Use of nanoparticles for improving the foaming behaviors of linear PP. J Appl Polym Sci2010; 117: 2979.
46.
ZhouYGSuBTurngLS.Fabrication of super-ductile PP/LDPE blended parts with a chemical foaming agent. J Appl Polym Sci2016; 133: 44101.
47.
ZhouYGChenTY.Combining foam injection molding with batch foaming to improve cell density and control cellular orientation via multiple gas dissolution and desorption processes. Polym Adv Technol2020; 31: 2136–2151.
48.
SuBZhouYGDongBB, et al. Effect of compatibility on the foaming behavior of injection molded polypropylene and polycarbonate blend parts. Polymers2019; 11: 300.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
