On-Line Characterization of Bulk Permeability and Race-Tracking During the Filling Stage in Resin Transfer Molding Process

Abstract

Resin Transfer Molding (RTM) is widely used to manufacture polymer composite materials. In this process, the fiber preform is placed in a closed mold and thermoset resin is injected to saturate the preform. After the resin cures the mold is opened and the net shape composite part is obtained. With RTM, one is capable of making complex and high quality composite parts with short cycle times. However, by introducing more complexity into the part, one also introduces higher probability of disturbances, such as race-tracking of resin during impregnation along preform edges. This can lead to incomplete saturation of fiber preform forming flaws such as dry spots in the composite part. The strength and existence of race-tracking is a function of the fabric type, perform manufacturing method, and their placement in the mold. It can vary from one part to the next in the same production run and usually it is not repeatable. The characterization of race-tracking and preform permeability is a key input for simulation tools that optimize the gates and vents locations and for designing advanced sensing and flow control strategies. This paper describes a method to estimate the strength and location of race-tracking and characterize the preform bulk permeability during the resin impregnation stage of RTM. The approach can be described in two steps. The first step generates simulations off line that map the overall range of potential disturbances likely to occur during the injection. The second step uses sensors placed in the mold, which allow one to identify the simulation within the database that resembles the experiment in terms of the filling behavior during the filling stage on the manufacturing platform. In the final step, this information is used to estimate race-tracking strength and location as well as the bulk permeability. Both experimental and numerical case studies show the reliability and accuracy of this method. It could be utilized for a broad range of applications such as active flow control, vent location optimization, and process monitoring of mold filling processes.

Get full access to this article

View all access options for this article.

References

1. Advani, S.G., Bruschke, M.V. and Parnas, R. (1994). Chapter 12: Resin Transfer Molding, In: S.G. Advani (ed.), Flow and Rheology in Polymeric Composites Manufacturing, pp. 465-516, Elsevier Publishers, Amsterdam .

2. Busch, J. (1998). Composites Molding Processes , Advanced Materials & Processes, 153(3): 25-26 .

3. Bickerton, S. and Advani, S.G. (1999). Characterization and Modeling of Race-tracking in Liquid Composite Molding Processes , Composites Science and Technology, 59(15): 2215-2229 .

4. Han, K., Wu, C.H. and Lee, J. (1993). Characterization and Simulation for RTM Race-tracking and Dry Spot Formation , In: Proceedings of Ninth Annual ASM-ESD.

5. Lawrence, J., Hsiao, K.-T., Simacek, P. and Advani S.G. (2002). An Approach to Couple Mold Design and On-line Control to Manufacture Complex Composites Parts by Resin Transfer Molding , Composites, Part A: Applied Science and Manufacturing, 33: 981-990 .

6. Luo, J., Zhang, Z.L. and Wang, B. (2001). Optimum Tooling Design for Resin Transfer Molding with Virtual Manufacturing and Artificial Intelligence , Composites Part A: Applied Science and Manufacturing, 32(6): 877-888 .

7. Nielsen, D. and Pitchumani, R. (2001). Intelligent Model-based Control of Preform Permeation in Liquid Composite Molding Processes, with Online Optimization , Composites Part A: Applied Science and Manufacturing, 32(12): 1789-1803 .

8. Demirci, H., Hamdi, H. and John P. Coulter (1994). Neural Network Based Control of Molding Processes , Journal of Materials Proceedings and Manufacturing Science, 6: 335-354 .

9. Demirci, H., Hamdi, H. and John P. Coulter (1995). Control of Flow Progression During Molding Processes , Journal of Materials Processing and Manufacturing Science, 7: 409-425 .

10.

10. Mogavero, J., Sun, J.Q. and Advani, S.G. (1997). A Nonlinear Control Method for Resin Transfer Molding , Polymer Composites, 18(41): 2-7 .

11.

11. Lunstorm, S. and Gebart, R. (1994). Influence from Process Parameters on Void Formation in RTM , Polymer Composites, 20(4): 25-33 .

12.

12. Beker, B., Barooah, P., Yoon, M.K. and Sun, J.Q. (1994). Sensor Based Modeling and Control of Fluid Flow in RTM , Journal of material Processing and Manufacturing Science, 7(2): 161-170 .

13.

13. Wang, T.J., Wu, C.H. and Lee, L.J. (1994). In-plane Permeability Measurement and Analysis in Liquid Composite Molding , Polymer Composites, 15(4): 134-142 .

14.

14. Weitzenbock, J.R., Shenoi, R.A. and Wilson, P.A. (1999). Radial Flow Permeability Measurement , Composites: Part A, 33: 781-796 .

15.

15. Nedanov, P. and Advani, S.G. (2002). A Method to Determine 3D Permeability of Fibrous Reinforcements , Journal of Composite Materials, 36: 241-254 .

16.

16. Luo, Y., Verpooest, I., Hoes, K., Vanheule, M. and Cardon, A. (2001). Permeability Measurement of Textile Reinforcements with Several Test Fluids , Composites Part A: 23: 1497-1504 .

17.

17. Chan, A.W. and Morgan, R.J. (1997). Modeling Race Tracking Effects in Liquid Composite Molding, CAE and Intelligent Processing of Polymeric Materials , AMSE, Materials Division, 79: 361-367 .

18.

18. Robitaille, F., Long, A.C., Rudd, C.D. and Souter, B.J. (1998). Measurement of In-plane Permeability for Sheared Preforms , In: Proceedings of the International Conference on Computer Methods in Composite Materials, pp. 495-504 .

19.

19. Laval, N., Sozer, E. and Advani, S.G. (2000). Characterization of Permeability Around a 90 Corner , Advanced Composite Letters, 17-24 .

20.

20. Bickerton, S., Sozer, E., Simacek, P. and Advani, S.G. (2000). Fabric Structure and Mold Curvature Effects on Preform Permeability and Mold Filling in the RTM Process , Composites Part A: Applied Science and Manufacturing, 93(10): 439-458 .

21.

21. Ramakrishnan, B. and Pitchumani, R. (2000). Fractal Permeation Characteristics of Preforms Used in Liquid Composite Molding , Polymer Composites, 21: 281-296 .

22.

22. Woerdeman, D.L., Phelan, F.R. and Parnas, R.S. (1999). Interpretation of 3D Permeability Measurements for RTM Modeling , Polymer Composites, 470-480 .

23.

23. Gokce, A. and Advani, S.G. (2001). Combinatorial Search to Optimize Vent Locations in the Presence of Disturbances in Liquid Composite Molding Processes, Submitted to Materials and Manufacturing Processes.

24.

24. Gokce, A. and Advani, S.G. (2003). Race Tracking Forecast in Liquid Composite Molding Processes Case Study: Vent Optimization to Minimize Dry Spot Formation , SAMPE Symposium and Exhibition, 19(4).

25.

25. Simacek, P. and Advani, S.G. (2002). LIMS 5.0 and LIMS UI User Manual, Tech. Report, CCM, University of Delaware.

26.

26. Maier, R.S., Rohaly, T.F., Advani, S.G. and Fickie, K.D. (1996). A Fast Numerical Method for Isothermal Resin Transfer Mold Filling , International Journal of Numerical Methods in Engineering, 39: 1405-1422 .

27.

27. Hsiao, K.-T., Devillard, M. and Advani, S.G. (2002). Streamlined Intelligent RTM Processing: From Design to Automation , In: Proceedings of 47th International SAMPE Symposium and Exhibition, 47: 454-465 .

28.

28. Gokce, A., Hsiao, K.-T. and Advani, S. G. (2001). A Method to Find Auxiliary Injection Gate Locations for Successful Mold Filling in Resin Transfer Molding Process , In: Proceedings of 46th International SAMPE Symposium and Exhibition, 46: 310-325 .

29.

29. Lin, M. and Hahn, H.T. (2000). Resin Transfer Molding Process Optimization , Composites, Part A: Applied Science and Manufacturing, 31: 361-371 .

30.

30. Mathur, R., Advani, S.G. and Fink, B.K. (1999). Use of Genetic Algorithms to Optimize Gate and Vent Locations for the RTM Process , Polymer Composites, 20(2).

31.

31. Advani, S.G. and Bruschke, M.V. (1994). A Numerical Approach to Model Non-isothermal, Viscous Flow with Free Surfaces Through Fibrous Media , Methods Fluids, 19: 575-603 .

32.

32. Fracchia, C.A., Castro, J. and Tucker III C.L. (1995). A Finite Element/Control Volume Simulation of RTM Filling , In: Proceedings of the American Society for Composites Fourth Annual Technical Conference.

33.

33. Advani, S.G. and Bruschke, M.V. (1990). A Finite Element/Control Volume Approach to Mold Filling in Anisotropic Porous Media , Polymer Composites, 11(6): 398-405 .

34.

34. Dominauskas, A., Heider, D. and Gillespie, J.W. (2003). Electric Time Domain Reflectometry Sensor for On-line Flow Sensing in Liquid Composite Molding Processing , Composites Part A: Applied Science and Manufacturing, 34(1): 67-74 .

35.

35. Estrada, G., Celine Vieux-Pernon and Advani, S.G. (2002). Experimental Characterization of the Influence of Tackifier Material on Preform Permeability , Composites Materials, 36(19): 2297-2310 .