Characterization of Composites Based on Natural and Glass Fibers Obtained by Vacuum Infusion

Abstract

The mechanical properties of composites based on different natural fibers and glass fibers using unsaturated polyester and modified acrylic as matrix are evaluated. In spite of the several works done in natural fiber composites, there are very few results on acrylic as matrix. Fabrication of the composites is done by means of vacuum infusion. Flexural, tension, and impact test are conducted on the composites. Ignition, thermal degradation, and water absorption are determined. Jute composite with unsaturated polyester resin as matrix showed the best results on flexural and tensile strengths and the lowest in impact energy, because of the strong interphase developed. Flax composites show higher impact energy than the other natural fiber composites, due to the existence of the effective energy dissipation mechanisms, like pull-out and axial splitting of the fibers. Scanning electron micrograph confirmed this fact. None of the samples resisted the five-second exposition to the flame on the ignition test. All of them were completely consumed, and flax composites burned the longest.

Keywords

RTM vacuum infusion natural fibers glass fibers mechanical properties ignition test water absorption

Get full access to this article

View all access options for this article.

References

Dash, B.N. , Rana, A.K. , Mishra, H.K. , Nayak, S.K. , Mishra, S.C. and Tripathy, S.S. (2000). Novel Low-cost jute-polyester Composites: III - Weathering and Thermal Behavior , J. Appl. Polym. Sci. 78(9): 1671-1679 .

Hughes, M. , Hill, C.A.S. and Hague, J.R.B. (2002). The Fracture Toughness of Bast Fibre Reinforced Polyester Composites: Part 1 - Evaluation and Analysis , J. Mat. Sci. 37(21): 4669-4676 .

Mwaikambo, L.Y. and Ansell, M.P. (2002). Chemical Modification of Hemp, Sisal, Jute, and Kapok Fibers by Alkalization , J. Appl. Polym. Sci. 84(12): 2222-2234 .

O’Dell, J.L. (1997). Natural Fibers in Resin Transfer Molded Composites . In: Proceedings of the 4th International Conference on Woodfiber-Plastic Composites, May 12-14, Madison, WI, USA, Forest Products Society, Madison, WI, USA, pp. 280-285 .

Rong, M.Z. , Zhang, M.Q. , Liu, Y. , Zhang, Z.W. , Yang, G.C. and Zeng, H.M. (2002). Interfacial Interaction in Sisal/Epoxy Composites and its Influence on Impact Performance , Polym. Compos. 23(2): 182-192 .

Mohanty, A.K. and Misra, M. (1995). Studies of Jute Composites - A Literature Review , Polym. Plast. Technol. 34(5): 729-792 .

Singh, B. , Gupta, M. and Verma, A. (1994). Studies of Polymer Composites Based on Sisal Polyester and Glass Modified Sisal Fibers, Filler and Unsaturated Polyester Resin , Res. Ind. 39(1): 38-42 .

Oksman, K. , Wallstróm, L. , Berglund, L. and Días Toledo Filho, R. (2001). Mechanical Properties and Morphology of Sisal Fibre-Epoxy Composites , Natural Polymers and Composites, 355-361 .

Munikenche Gowda, T. , Naidu, A.C.B. and Chhaya Rajput , (1999). Some Mechanical Properties of Untreated Jute-fabric-Reinforced Polyester Composites , Composite Part A 30: 277-284 .

10.

Ishikawa, T and Chou, T.W. (1982). Stiffness and Strength Behaviour of Woven Fabric Composites , J. Mater. Sci., 17: 3211-3220 .

11.

Matemilola, S.A. and Stronge, W.J. (1995). Impact Micro-damage in Resin Transfer (RTM) Carbon Fibre Composite Plates, In: Williams, J.G. and Pavan, A. (eds), Impact and Dynamic Fracture of Polymers and Composites, ESIS 19 pp. 371-381, Mechanical Engineering Publications, London .

12.

Karbhari, V.M. (1997). Impact Characterization of RTM Composites , J. Mater. Sci., 32: 4159-4166 .

13.

Bledzki, A.K. and Gassan, J. (1999). Composites Reinforced with Cellulose Based Fibers , Prog. Polym. Sci., 24: 221-224 .

14.

Browder, W.D. (2000). Natural Fibre Composites: Where can Flax Compete with Glass? , Sampe Journal, 36(6): 18-23 .

15.

Nabi Saheb, D. and Jog, J.P. (1999). Natural Fibre Polymer Composites: A Review , Advance in Polymer Technology, 18(4): 351-363 .

16.

Bledzki, A.K. , Reihmane, S. and Gassan, S. (1996). Properties and Modification Methods for Vegetable Fibers for Natural Fibre Composites , J. Appl. Polym. Sci., 59: 1329-1336 .

17.

Kandachar, Prabhu , (2001). Agricultural Fibers for Product Design and Development , In: Proceeding of Workshop Development by Design, MIT, Cambridge, July 22.

18.

Romhaný, G. , Karger-Kocsis, J. and Czigány, T. (2003). Tensile Fracture and Failure Behaviour of Thermoplastic Starch with Unidirectional and Cross-Ply Flax Fibre Reinforcements , Macromol. Mater. Eng., 288: 699-707 .

19.

Beaumont, P.W.R. , Riewald, P.G. and Zweden, C. (1975). Foreign Object Impact Damage to Composites , ASTM STP, 568: 134-138 .

20.

Dash, B.N. , Rana, A.K. , Mishra, H.K. , Nayak, S.K. , Mishra, S.C. , Tripathy, S.S. (2000). Novel Low-cost Jute-Polyester Composites: III-Weathering and Thermal Behavior , J. Appl. Polym. Sci. 78(9): 1671-1679 .

21.

Riccieri, E. , Hecker de Carvalho, L. and Vázquez, A. (1999). Interfacial Properties and Initial Step of Water Sorption in Unidirectional Unsaturated Polyester/Vegetable Fibers Composites , Polymer Composites, 20(1): 29-37 .

22.

Fraga, A.N. , Alvarez, V.A. , Vázquez, A. and de la Osa, O. (2003). Relationship between Dynamical-Mechanical Properties and Water Absorption of Unsaturated Polyester and Vinyl Ester Glass Fibre Composites , J. Comp. Materials, 37(17): 1553-1574 .