Modeling the Effect of Fiber Diameter and Fiber Bundle Count on Tow Impregnation during Liquid Molding Processes

Abstract

This paper explores the effect of fiber diameter and fiber bundle count on tow impregnation during liquid molding processes. Resin and fiber wetting properties play an important role on the resin infiltration behavior within a single fiber tow. Dynamic and equilibrium microflow models, based on Darcy’s Law and force equilibrium at the resin flow front, assume that the infiltration of the resin is driven through capillary pressure and hindered by the entrapped gas within the tow. The results of the dynamic model show that the fiber tow count and the fiber diameter have a significant effect on the tow infiltration time. The infiltration time is 10 times longer for a 60 K carbon fiber tow than for a 6 K one. The infiltration time is also inversely proportional to the fiber diameter. As the fiber diameter is decreased 100 times, from 3.5 mm to 35 nm, the infiltration time increases 100 times for the same diameter tow. It also shows that fiber volume fraction also has a significant effect on the tow infiltration time and any fiber volume variations along the fiber tow could lead to dry spots in the composite due to the large differences in infiltration rates. The model indicates that the entrapment of a critical amount of air within a tow will lead to higher than acceptable void contents.

Keywords

impregnation microflow nanofibers

Get full access to this article

View all access options for this article.

References

Parnas, R.S. and Phelan, F.R., Jr. (1991). The Effect of Heterogeneous Porous Media on Mold Filling in Resin Transfer Molding , SAMPE Quarterly, 22(2): 53–60 .

Binetruy, C. , Hilaire, B. and Pabiot, J. (1997). The Interactions between Flows Occurring Inside and Outside Fabric Tows during RTM , Composites Science and Technology, 57: 587–596 .

Sadiq, T.A.K. , Advani, S.G. and Parnas, R.S. (1995). Experimental Investigation of Transverse Flow through Aligned Cylinders , International Journal of Multiphase Flow, 21(5): 755–774 .

Summerscales, J. (1993). A Model for the Effect of Fibre Clustering on the Flow Rate in Resin Transfer Moulding , Composites Manufacturing, 4(1): 27–31 .

Astrom, B.T. , Pipes, R.B. and Advani, S.G. (1992). On Flow through Aligned Fiber Beds and its Application to Composite Processing , Journal of Composite Materials, 26(9): 1351–1373 .

Papathanasiou, T.D. (1996). A Structure-oriented Micromechanical Model for Viscous Flow through Square Array of Fibre Clusters , Composites Science and Technology, 56: 1055–1069 .

Young, W.B. (1996). The Effect of Surface Tension on Tow Impregnation of Unidirectional Fibrous Preform in Resin Transfer Molding , Journal of Composite Materials, 30(11): 1191–1209 .

Binetruy, C. , Hilaire, B. and Pabiot, J. (1998). Tow Impregnation Model and Void Formation Mechanisms during RTM , Journal of Composite Materials, 32(3): 223–245 .

Bayramli, E. and Powell, R.L. (1992). Impregnation Dynamics of Carbon Fiber Tows , Journal of Composite Materials, 26(10): 1427–1442 .

10.

Chwastiak, S. (1973). A Wicking Method for Measuring Wetting Properties of Carbon Yarns , Journal of Colloid and Interface Science, 42: 298–309 .

11.

Karbhari, V.M. and Palmese, G.R. (1997). Sizing Related Kinetic and Flow Considerations in the Resin Infusion of Composites , Journal of Materials Science, 32: 5761–5774 .

12.

Palmese, G.R. and Karbhari, V.M. (1995). Effects of Sizings on Microscopic Flow in Resin Transfer Molding , Polymer Composites, 16(4): 313–318 .

13.

Chang, H.W. , Smith, R.P. , Li, S.K. and Neumann, A.W. (1985). Wettability of Reinforcing Fibers, In: Ishida, H. and Kumar, G. (eds), Molecular Characterization of Composite Interfaces, pp. 413–421, Plenum Press, New York .

14.

Hsieh, Y.-L. and Yu, B. (1992). Liquid Wetting, Transport, and Retention Properties of Fibrous Assemblies Part I. Water Wetting Properties of Woven Fabrics and their Constituent Single Fibers , Textile Research Journal, 62(11): 677–685 .

15.

Bayramli, E. and Powell, R.L. (1992). Experimental Investigations of the Axial Impregnation of Oriented Fiber Bundles by Capillary Forces, U.S. Army Ballistic Research Laboratory Technical Report No BRL-CR-690.

16.

Binetruy, C. , Hilaire, B. and Pabiot, J. (2000) The Influence of Fiber Wetting in Resin Transfer Molding: Scale Effects , Polymer Composites, 21(4): 548–557 .

17.

Wu, S. (1982). Polymer Interface and Adhesion, Marcel Dekker Inc., New York .

18.

Bayramli, E. and Powell, R.L. (1990). The Normal (Transverse) Impregnation of Liquids into Axially Oriented Fiber Bundles , Journal of Colloid and Interface Science, 138(2): 346–353 .

19.

Steenkamer, D.A. , McKnight, S.H. , Wilkins, D.J. and Karbhari, V.M. (1995). Experimental Characterization of Permeability and Fibre Wetting for Liquid Moulding , Journal of Materials Science, 30: 3207–3215 .

20.

Yang, X.F. and Xi, X.M. (1995). Critical Wetting Angle for Spontaneous Liquid Infiltration into Orderly Packed Fibres or Spheres , Journal of Materials Science, 30: 5099–5102 .

21.

Foley, M.E. (2003). The Microflow Behavior and Interphase Characterization of Fiber Reinforced Polymer Composites, PhD Dissertation, University of Delaware.

22.

Bruschke, M.V. (1992). A Predictive Model for Permeability and Non-isothermal Flow of Viscous and Shear-Thinning Fluids in Anisotropic Fibrous Media, PhD Dissertation, University of Delaware.

23.

Bernet, N. , Michaud, V. , Bourban, P.-E. and Manson, J.-A.E. (1991). An Impregnation Model for the Consolidation of Thermoplastic Composites made from Commingled Yarns , Journal of Composite Materials, 33(8): 751–772 .