An Equivalent Medium Method for the Vacuum Assisted Resin Transfer Molding Process Simulation

Abstract

Computer simulation has been an efficient and cost-effective tool for liquid composite molding, including resin transfer molding (RTM), vacuum assisted resin transfer molding (VARTM), and resin infusion, compared to trial and error. The control volume finite element method (CVFEM) has been the predominant method for simulation. When the CVFEM simulation is used for the VARTM process, because of the existence of two distinct flow media: fiber preform and high permeable media (HPM), 3-D models are required. Since the HPM is usually much thinner than the fiber preform, a large number of nodes and elements need to be used in simulation, which significantly increases the computation load and time. In addition, the time-consuming preprocessing process makes simulation not feasible for industry applications.

This article presents an equivalent medium method (EMM) for fast and accurate VARTM process simulation. This method increases the thickness of the HPM or both the HPM and the fiber preform and applies the equivalent material properties. This is an improved method over previously presented equivalent permeability method (EPM) by correcting its two shortcomings: (1) The EPM does not account for the influence of the porosity of HPM, thus the resin flow through HPM is changed and (2) The EPM does not consider the change of through-thickness permeability after the equivalence. A new mesh generation algorithm is also discussed, which provides a faster and more convenient way for preprocessing. The approach presented in this article provides the fundamental for developing a universal computer simulation tool for both the RTM and VARTM processes. The effectiveness of this approach has been validated by comparing to the conventional CVFEM simulation and experiments.

Keywords

equivalent medium method (EMM)vacuum assisted resin transfer molding (VARTM)Seemann composite resin infusion molding process (SCRIMP)high permeable medium (HPM)control volume finite element method (CVFEM)

Get full access to this article

View all access options for this article.

References

Bruschke, M.V. and Advani, S.G. (1991). Filling Simulation of Complex Three-Dimensional Shell-Like Structures , SAMPE Quarterly, 23(1): 2–11 .

Young, W.B. , Han, K. , Fong, L.H. and Lee, L.J. (1991). Flow Simulation in Molds with Preplaced Fiber Mats , Polymer Composites, 12(6): 391–404 .

Liu, X.L. (2000). Isothermal Flow Simulation of Liquid Composite Molding , Composites Part A, 31(12): 1295–1302 .

Lin, R.J. , Lee, L.J. and Liou, M.J. (1991). Non-Isothermal Mold Filling and Curing Simulation in Thin Cavities with Preplaced Fiber Mats , International Journal of Polymer Processing, VI(4): 4356–4369 .

Young, W.B. (1994). Three-Dimensional Nonisothermal Mold Filling Simulation in Resin Transfer Molding , Polymer Composites, 15(2): 118–127 .

Lee, L.J. , Young, W.B. and Lin, R.J. (1994). Mold Filling and Curing Modeling of RTM and SCRIM Processes , Composite Structures, 27(1–2): 109–120 .

LIMS , Center for Composite Materials, University of Delaware, www.ccm.udel.edu/Research/AMIPCindex.html.

PAM-RTM , ESI Group, www.esi-group.com.

Polyworx, www.polyworx.com.

10.

Cowley, S.J. (2001). Laminar Boundary-Layer Theory: A 20th Century Paradox?, In: Aref, H. and Phillips, J.W. (eds), Mechanics for a New Millenium: Proceedings of the 20th International Congress of Theoretical and Applied Mechanics, Chicago, Illinois , 27 August–2 September 2000, Kluwer, Dordrecht, pp. 389–411.

11.

Mathur, R. , Heider, D. , Hoffmann, C. , Gillespie, Jr., J.W. , Advani, S.G. and Fink, B.K. (2001). Flow Front Measurements and Model Validation in the Vacuum Assisted Resin Transfer Molding Process , Polymer Composites, 22(4): 477–490 .

12.

Loos, A.C. , Sayre, J. , McGrane, R. and Grimsley, B. (2001). VARTM Process Model Development, In: Proceedings of the 46th International SAMPE Symposium and Exhibition, Long Beach, CA , SAMPE Publishing, Vol. 46(I), pp. 1049–1061 .

13.

Mohan, R.V. , Shires, D.R. , Tamma, K.K. and Ngo, N.D. (1998). Flow Channels/Fiber Impregnation Studies for the Process Modeling/Analysis of Complex Engineering Structures Manufactured by Resin Transfer Molding , Polymer Composites, 19(5): 527–542 .

14.

Sun, X.D. , Li, S.J. and Lee, L.J. (1998). Mold Filling Analysis in Vacuum-Assisted Resin Transfer Molding. Part I: SCRIMP Based on a High-Permeable Medium , Polymer Composites, 19(6): 807–817 .

15.

Ni, J. , Li, S.J. , Sun, X.D. and Lee, L.J. (1998). Mold Filling Analysis in Vacuum-Assisted Resin Transfer Molding. Part II: SCRIMP Based on Grooves , Polymer Composites, 19(6): 818–829 .

16.

Tari, M.J. , Imbert, J.P. , Lin, M.Y. , Lavine, A.S. and Hahn, H.T. (1998). Analysis of Resin Transfer Molding with High Permeability Layers, Transactions of the ASME , Journal of Manufacturing Science and Engineering, 120(3): 609–616 .

17.

Hsiao, K.T. , Mathur, R. and Advani, S.G. (2000). A Closed Form Solution for Flow During the Vacuum Assisted Resin Transfer Molding Process, Transactions of the ASME , Journal of Manufacturing Science and Engineering, 122(3): 463–475 .

18.

Han, K. , Jiang, S.L. , Zhang, C. and Wang, B. (2000). Flow Modeling and Simulation of SCRIMP for Composite Manufacturing , Composites Part A, 31(1): 79–86 .

19.

Chen, R.L. , Dong, C.S. , Liang, Z.Y. , Zhang, C. and Wang, B. (2004). Flow Modeling and Simulation for Vacuum Assisted Resin Transfer Molding Process with the Equivalent Permeability Method , Polymer Composites, 25(2): 146–164 .

20.

D'Arcy, H. (1856). Les Fontaines Publiques de la villa de Dijon, Dalmont, Paris.