Cement Composites Reinforced with Surface Modified Coir Fibers

Abstract

An experimental investigation of coir mesh reinforced mortar (CMRM) is conducted using nonwoven coir mesh matting. The main parameters in this study are the fiber volume fraction (number of mesh layers) and fiber surface treatment with a wetting agent. The composites are subjected to the four-point bending test. The short-term mechanical properties of CMRM are discussed. Scanning electron micrograph analysis is used to observe the fiber—matrix interfacial characteristics. The results indicate that the addition of coir mesh to mortar significantly improves the composite post-cracking flexural stress, toughness, ductility, and toughness index, compared to plain mortar materials. The Albatex^© FFC wetting agent (2-ethylhexanol) can effectively improve water absorption of coir fiber and enhance the fiber—matrix bonding strength. These coir mesh reinforced composites may be useful in civil engineering applications.

Keywords

mechanical properties fiber reinforcement mortar cement manufacture coir fiber.

Get full access to this article

View all access options for this article.

References

Thampan, P.K. (1991). Hand Book on Coconut Palm, Vol. 15, 260—274, Oxford and IBH Publishing Co. , New Delhi.

Moir, B. (2002). Coir Globally: Status and Perspectives, In: Proceeding of International Coir Convention, Colombo, Sri Lanka, 23—29.

Abad, M. , Nouera, P. , Puchades, R. , Maquieira, A. and Noguera, V. (2002). Physico-chemical and Chemical Properties of Some Coconut Coir Dusts for Use as a Peat Substitute for Containerised Ornamental Plants, Bioresource Technology, 82: 241—245.

Aggarwal, L.K. (1992). Studies on Cement-bonded Coir Fibre Boards, Cement & Concrete Composites, 14: 63—69.

Shimizu, G. and Jorillo, P. (1992). Coir Fibre Reinforced Cement Based Composite — Part 1: Microstructure and Properties of Fibre-mortar, In: Fibre Reinforced Cement and Concrete: The 4th International Symposium held by RILEM, University of Sheffield, UK, E & FN Spon., Sheffield.

Viswanathan, R. and Gothandapani , L. (1999). Mechanical Properties of Coir Pith Particle Board, Bioresource Technology, 67: 93—95.

Dam, J.E.G.V. (2002). Coir Processing Technologies — Improvement of Drying, Softening, Bleaching and Dyeing Coir Fibre/Yarn and Printing Coir Floor Coverings, Department of Fibres and Cellulose, Agrotechnological Research Institute (ATO bv), Wageningen , The Netherlands.

Brouwer, W.D.R. (2005). Natural Fibre Composites in Structural Components: Alternative Applications for Sisal? In: Common Fund for Commodities — Alternative Applications for Sisal and Henequen, Economic and Social Department, Buizerdlaan, The Netherlands.

Parton, G.M. and Shendy-El-Barbary, M.E. (1982). Polystyrene Concrete Sandwich Beams: Stiffness and Ultimate Load Analysis, International Journal of Cement Composites and Lightweight Concrete, 4(4): 199—208.

10.

Mansur, M.A. and Aziz, M.A. (1983). Study of Bamboo-mesh Reinforced Cement Composites, The International Journal of Cement Composites and Lightweight Concrete, 5(3): 165—171.

11.

Currie, B. and Gardiner, T. (1989). Effect of Low Temperature on the Flexural Behaviour of Polypropylene Mesh Reinforced Fibre Cement Composite, Cement and Concrete Composites, 11(3): 149—152.

12.

Mu, B. and Meyer, C. (2002). Flexural Behavior of Fiber Mesh-reinforced Concrete with Glass Aggregate, ACI Materials Journal, 99(5): 425—434.

13.

Rao, G.V. (2002). Coir Geotextiles Strategic Management Initiatives , In: Proceeding of International Coir Convention , Colombo, Sri Lanka.

14.

Callister, W.D. (2000). Materials Science and Engineering: An Introduction, 5th edn, Wiley , New York, xxi, p. 871.

15.

Bismarck, A. , Mohanty, A.K. , Aranberri-Askargorta , I. , Czapla, S. , Misra, M. , Hinrichsen, G. and Springer, J. (2001). Surface Characterization of Natural Fibers; Surface Properties and the Water Up-take Behavior of Modified Sial and Coir Fibers, Green Chemistry , 3: 100—107.

16.

Slade, P.E. (1998). Handbook of Fiber Finish Technology, Marcel Dekker, Inc., New York.