Experimental Investigation of the Controlled Atmospheric Pressure Resin Infusion (CAPRI) Process

Abstract

Controlled atmospheric pressure resin infusion (CAPRI) is a variation of the vacuum-assisted resin transfer molding (VARTM) process. The CAPRI process increases the fiber volume fraction of the preform prior to infusion via debulking and applies a reduced pressure gradient during infusion to minimize thickness gradients during processing. This study experimentally investigates the effect of debulking and reduced pressure gradient on the incoming material parameters, process behavior and final dimensional tolerances. The effect of debulking on fabric permeability and compaction behavior has been investigated and shows a significant impact on the infusion time and final fiber volume fraction. Several E-glass plain weave preforms have been infused and flow, pressure and thickness data has been recorded and compared to traditional VARTM processing. A previously developed model uses the experimentally obtained permeability data and good agreement of the flow behavior is observed, the CAPRI process decreases thickness gradients to less than 1% while increasing fiber volume fraction by 5% in the composite part.

Keywords

liquid composite molding vacuum assisted resin transfer molding permeability.

Get full access to this article

View all access options for this article.

References

Lewit, S.M. and Jakubowski, J.C. (1997). Low cost VARTM Process for Commercial and Military Applications, In: 42nd International SAMPE Symposium, 4-8 May, 42(2): 1173-1187.

Beckwith, S.W. and Hyland, C.R. (1998). Resin Transfer Molding: A Decade of Technology Advances, SAMPE Journal, 34(6).

Juska, T.D. , Dexter, H.B. and Seemann, W.H. (1998). Pushing the Limits of VARTM, In: 43rd International SAMPE Symposium, Vol. 43, Book 1, May, pp. 33-43.

Seemann, W. Plastic Transfer Molding Techniques For The Production Of Fiber Reinforced Plastic Structures, US Patent 4,902,215 (US), 02/20/90.

Seemann, W. Plastic Transfer Molding Techniques For The Production Of Fiber Reinforced Plastic Structures, US Patent 5,052,906 (US), 10/01/91.

Heider, D. and Gillespie Jr, J.W. (2004). Automated VARTM Processing of Large-Scale Composite Structures, Journal of Advanced Materials , 36(4).

Acheson, J.A. , Simacek, P. and Advani, S.G. (2004). The Implications of Fiber Compaction and Saturation on fully Coupled VARTM Simulation, Compos . Part A, 35: 159-169.

Lopatnikov, S. , Simacek, P. , Gillespie Jr, J.W. and Advani, S.G. (2004). A Closed form Solution to Describe Infusion of Resin under Vacuum in Deformable Fibrous Porous Media, Modeling Simul. Mater. Sci. Eng., 12: 191-204.

Woods, J. , Modin, A.E. , Hawkins, R.D. and Hanks, D.J. Controlled Atmospheric Pressure Infusion Process, International Patent WO 03/101708 A1.

10.

Zhang, Y. , Scholz, S. , Amouroux, S. , Gillespie Jr, J.W. and Heider, D. (2005). Measurement of Transverse Permeability Using Gaseous and Liquid Flow, In: Proceedings of the American Society for Composites. 20th Technical Conference, Philadelphia .

11.

Heider, D. , Epple, S. and Gillespie Jr, J.W. (2001). Flow Rate Control During Vacuum-Assisted Resin Transfer Molding (VARTM) Processing, In: International SAMPE Symposium and Exhibition (Proceedings), 461: 1061-1071.

12.

Bender, D. , Schuster, J. and Heider, D. (2006). Flow Rate Control during Vacuum-Assisted Resin Transfer Molding (VARTM) Processing, Composites Science and Technology, 66(13): 2265.

13.

Chen, B. and Chou, T.W. (1999). Compaction of Woven-Fabric Preforms in Liquid Composite Molding Processes: Single-layer Deformation, Compos. Sci. Technol., 59: 1519-1526.

14.

Robitaille, F. and Gauvin, R. (1998). Compaction of Textile Reinforcements for Composites Manufacturing. II: Compaction and Relaxation of Dry and H2O-Saturated Woven Reinforcements, Polym. Compos. , 19: 543-557.

15.

Hsiao, K.T. , Mathur, R. , Gillespie Jr, J.W. , Fink, B.K. and Advani, S.G. (2000). A Closed Form Solution for the Vacuum-Assisted Resin Transfer Molding Process , Journal of Manufacturing Science, 122: 463-472.

16.

Mathur, R. , Heider, D. , Hoffmann, C. , Gillespie Jr, J.W. , Advani, S.G. and Fink, B.K. (2001). Flow Front Measurements and Model Validation in the Vacuum-Assisted Resin Transfer Molding Process, Polymer Composites, 22(4): 477-490.