Al—(1, 3, 5, 7, 10 vol%) SiC nanocomposites were produced by mechanical alloying (MA) and double pressing/sintering route. The characteristics of the milled powders and the consolidate specimens were examined using high resolution scanning electron microscopy and X-ray diffraction method. Compression and hardness tests were used to study the effect of SiC volume fraction on the strength of Al—SiC nanocomposites. It was shown that with increasing the SiC volume fraction, finer particles with narrower size distribution and smaller crystallite size are obtained after MA. During sintering close to the melting point of aluminum, the presence of nanometer-scaled SiC particles was found to hinder the grain growth significantly. The Al matrix with a higher SiC content exhibited more potential for grain boundary pinning, i.e., smaller grain size was obtained at higher SiC volume fractions. Consequently, an improved mechanical strength was obtained. The processing method (MA/pressing/sintering) can be used for fabrication of near-net shape Al matrix nanocomposites.
Nayeb-Hashemi, H. and Shan, D. (1999). Evaluation of Heat Damage on B4C Particulate Reinforced Aluminum Alloy Matrix Composite Using Acoustic Emission Techniques, Mater. Sci. Eng. A, 266: 8-17.
2.
Kok, M. ( 2005). Production and Mechanical Properties of Al2O3 Particle-reinforced 2024 Aluminum Alloy Composites, J. Mater. Proc. Tech., 161: 381-387.
3.
Prabhu, B., Suryanarayana, C., An, L. and Vaidyanathan, R. ( 2006). Synthesis and Characterization of High Volume Fraction Al-Al2O3 Nanocomposite Powders by High-energy Milling, Mater. Sci. Eng. A, 425: 192-200.
4.
Zhang, D.L., Liang, J. and Wu, J. ( 2004). Processing Ti3Al-SiC Nanocomposites Using High Energy Mechanical Milling, Mater. Sci. Eng. A, 375-377: 911-916.
5.
Razavi Hesabi, Z., Hafizpour, H.R. and Simchi, A. (2007). An Investigation on the Compressibility of Aluminum/Nano-alumina Composite Powder Prepared by Blending and Mechanical Milling, Mater. Sci. Eng. A, 454-455: 89-98.
6.
Weiser, M.W. and De Jonghe, L.C. ( 1988). Inclusion Size and Sintering of Composite Powders, J. Amer. Ceram. Soc., 71: 125-127.
Yang, Y., Lan, J. and Li, X. ( 2004). Study on Bulk Aluminum Matrix Nano-composite Fabricated by Ultrasonic Dispersion of Nano-sized SiC Particles in Molten Aluminum Alloy, Mater. Sci. Eng. A, 380: 378-383.
9.
Ma, Z.Y. , Tjong, S.C. and Li, Y.L. (1999). The Performance of Aluminum-matrix Composites with Nanometric Particulate Si-N-C Reinforcement, Comp. Sci. Tech., 59: 263-270.
10.
Goujon, C. and Goeuriot, P. ( 2001). Solid State Sintering and High Temperature Compression Properties of Al-alloy5000/AlN Nanocomposites, Mater. Sci. Eng. A, 315: 180-188.
11.
Williamson, G.K. and Hall, W.H. (1953). X-Ray Line Broadening from Filed Aluminum and Wolfram, Acta Metall., 1: 22-31.
12.
Schatt, W. and Wieters, K.P.S. ( 1997). Powder Metallurgy: Processing and Materials, EPMA, Shrewsbury, UK.
13.
Kamrani, S. , Simchi, A., Riedel, R. and Seyed Reihani , S.M. (2007). Effect of Reinforcement Volume Fraction on Mechanical Alloying of Al-SiC Nanocomposite Powders, Powder Metall., 50: 276-282.
14.
Zhang, Z., Zhou, F. and Lavernia, E.J. ( 2003). On the Analysis of Grain Size in Bulk Nanocrystalline Materials via X-ray Diffraction, Metall. Mater. Trans., 34A: 1349-1355.
15.
Suryanarayana, C. (2001). Mechanical Alloying and Milling, Prog. Mater. Sci., 46: 1-184.
16.
Zhang, D.L. (2004). Processing of Advanced Materials Using High-energy Mechanical Milling, Prog. Mater. Sci., 49: 537-560.
17.
Chung, K.H. , He, J., Shin, D.H. and Schoenung , J.M. (2003). Mechanisms of Microstructure Evolution During Cryomilling in the Presence of Hard Particles, Mater. Sci. Eng. A, 356: 23-31.
18.
Tavakoli, A.H. , Simchi, A. and Seyed Reihani , S.M. (2005). Study of the Compaction Behavior of Composite Powders Under Monotonic and Cyclic Loading, Comp. Sci. Tech., 65: 2094-2104.
19.
Hafizpour, H.R. and Simchi, A. (2008). Investigation on Compressibility of Al-SiC Composite Powders, Powder Metall., 51: 217-223.
20.
Durisin, J. , Durisinova, K., Orolınova , M. and Saksl, K. (2004). Effect of the MgO Particles on the Nanocrystalline Copper Grain Stability, Mater. Lett., 58: 3796-3801.
21.
Tang, F., Hagiwara, M. and Schoenung, J.M. ( 2005). Microstructure and Tensile Properties of Bulk Nanostructured Al-5083/SiCp Composites Prepared by Cryomilling, Mater. Sci. Eng. A, 407: 306-314.
22.
Munoz-Morris, M.A., Garcia Oca, C. and Morris, D.G. (2002). An Analysis of Strengthening Mechanisms in a Mechanically Alloyed, Oxide Dispersion Strengthened Iron Aluminide Intermetallic, Acta Mater., 50: 2825-2836.
23.
Tong, X.C. and Ghosh, A.K. ( 2001). Fabrication of In Situ TiC Reinforced Aluminum Matrix Composites, J. Mater. Sci., 36: 4059-4069.
24.
Premkumar, M.K., Lawley, A. and Koczak, M.J. (1994). Mechanical Behavior of Powder Metallurgy Al-Fe-Ni Alloys, Mater. Sci. Eng. A, 174: 127-139.
25.
Lee, J.C. , Byun, J.Y., Oh, C.S., Seok, H.K. and Lee, H.I. (1997). Effect of Various Processing Methods on the Interfacial Reactions in SiCp/2024 Al Composites, Acta Mater., 45: 5303-5315.
26.
Kubota, M. ( 2007). Properties of Nano-structured Pure Al Produced by Mechanical Grinding and Spark Plasma Sintering, Mater. Sci. Eng. A, 434-435: 294-297.
27.
Kubota, M. and Wynne, B.P. ( 2007). Electron Backscattering Diffraction Analysis of Mechanically Milled and Spark Plasma Sintered Pure Aluminium, Scrip. Mater. , 57: 719-722.
28.
Witkin, D.B. and Lavernia, E.J. ( 2006). Synthesis and Mechanical Behavior of Nanostructured Materials via Cryomillin, Prog. Mater. Sci., 51: 1-60.
29.
Balog, M., Izdinsky, K., Nagy, J., Simancik, F. and Donic, T. ( 2005). Ultra-fine Grained PM Al Profiles, In: Proceedings of the International Conference Deformation and Fracture in structural PM Materials, Stara Lensa, Slovak Republic, pp. 301-307.
