Compression and Relaxation Behavior of Dry Fiber Preforms for Resin Transfer Molding

Abstract

Compression and relaxation behavior of various fiber preforms for resin transfer molding was investigated experimentally through compression, relaxation, and decompression procedures. A simple Maxwell model was used in order to predict the nonlinear compression and relaxation behavior, and numerical simulation was performed for a unit cell of the fiber preform by using the finite-element method. As the fiber volume fraction is larger than 0.4, compressive stresses acting on the woven fabric increased linearly with increasing fiber volume fraction. A typical hysteresis occurred due to relaxation behavior of the fiber preform during compression and decompression test. It was also found that numerical analysis yields slightly lower displacement field than experimental results under the same compressive force. However, experimental results were in good agreement with the analytic results obtained by considering the viscoelasticity of fiber preforms.

Keywords

resin transfer molding viscoelasticity compression behavior relaxation behavior.

Get full access to this article

View all access options for this article.

References

Harper, C.A. ( 2006). Handbook of Plastic Processes, Wiley-Interscience , Hoboken, NJ.

Somashekar, A.A. , Bickerton, S. and Bhattacharyya , D. (2006). An Experimental Investigation of Non-elastic Deformation of Fibrous Reinforcements in Composites Manufacturing, Composites Part A: Applied Science and Manufacturing, 37: 858-867.

Shin, D.D. and Hahn, H.T. ( 2004). Compaction of Thick Composites: Simulation and Experiment , Polymer Composites, 25(1): 49-59.

Kang, M.K. , Lee, W.I. and Hahn, H.T. ( 2001). Analysis of Vacuum Bag Resin Transfer Molding Process , Composites Part A: Applied Science and Manufacturing, 32: 1553-1560.

Jiang, Z. , Liu, X. , Zhang, H. , Li, G. and Lian, J. ( 2005). An Analytical Model for Elastic Stress Field Distribution in Fibre Composite with Partially Debonded Interface, Composites Science and Technology, 65(7-8): 1176-1194.

Bigaud, D. , Dreano, L. and Hamelin, P. ( 2005). Models of Interactions between Process, Microstructure, and Mechanical Properties of Composite Materials - A Study of the Interlock Layer-to-Layer Braiding Technique, Composite Structures, 67(1): 99-114.

Hsiao, K.T. , Devillard, M. and Advani, S.G. ( 2004). Simulation Based Flow Distribution Network Optimization for Vacuum Assisted Resin Transfer Moulding Process, Modelling and Simulation in Materials Science and Engineering, 12: S175-S190.

Acheson, J.A. , Simacek, P. and Advani, S.G. (2004). The Implementations of Fiber Compaction and Saturation of Fully Couple VARTM Simulation, Composites Part A: Applied Science and Manufacturing, 35(2): 159-169.

Chen, Z.R. and Ye, L. ( 2006). A Micromechanical Compaction Model for Woven Fabric Preforms . Part II: Multilayer, Composites Science and Technology, 66(16): 3263-3272.

10.

Bickerton, S. , Buntain, M.J. and Somashekar , A.A. (2003). The Viscoelastic Compression Behavior of Liquid Composite Molding Preforms , Composites Part A: Applied Science and Manufacturing, 34(5): 431-444.

11.

Somashekar, A.A. , Bickerton, S. and Bhattacharyya , D. (2007). Exploring the Non-Elastic Compression Deformation of Dry Glass Fibre Reinforcements , Composites Science and Technology, 67(2): 183-200.

12.

Buntain, M.J. and Bickerton, S. (2007). Modeling Forces Generated Within Rigid Liquid Composite Molding Tools. Part A: Experimental Study, Composites Part A: Applied Science and Manufacturing, 38: 1729-1741.

13.

Kelly, P.A. , Umerb, R. and Bickerton, S. ( 2006). Viscoelastic Response of Dry and Wet Fibrous Materials During Infusion Processes, Composites Part A: Applied Science and Manufacturing, 37(6): 868-873.

14.

Chen, B. and Chou, T. (1999). Compaction of Woven-Fabric Preforms in Liquid Composite Molding Processes: Single-layer Deformation, Composites Science and Technology, 59: 1519-1526. 15. Ouahbi, T., Saouab, A., Bréard, J., Ouagne, P. and Chatel, S. (2007). Modeling of HydroMechanical Coupling in Infusion Processes, Composites Part A: Applied Science and Manufacturing, 38: 1646-1654.

15.

Bruschke, M.V. and Advani, S.G. (2004). A Finite Element/Control Volume Approach to Mold Filling in Anisotropic Porous Media, Polymer Composites, 11(6): 398-405.

16.

Cho, Y.K., Song, Y.S., Kang, T.J., Chung, K. and Youn, J.R. (2003). Permeability Measurement of a Circular Braided Preform for Resin Transfer Molding, Fibers and Polymers, 4(3): 135-144. 18. Seong, D.G., Chung, K., Kang, T.J. and Youn, J.R. (2002). A Study on Resin Flow Through a Multi-layered Preform in Resin Transfer Molding, Polymers and Polymer Composites, 10(7): 493-509.

17.

Falzon, P.J. , Herszberg, I. and Karbhari, V.M. (1996). Effects of Compaction on the Stiffness and Strength of Plain Weave Fabric RTM Composites, Journal of Composite Materials, 30: 1210-1247.

18.

Comas-Cardona, S. , Binetruya, C. and Krawczak, P. (2007). Unidirectional Compression of Fibre Reinforcements, Composites Science and Technology , 67(3-4): 638-645.

19.

Deleglise, M. , Binetruy, C. and Krawczak, P. (2006). Simulation of LCM Processes Involving Induced or Forced Deformations, Composites, Part A: Applied Science and Manufacturing, 37(6): 874-880.

20.

Lin, H. , Sherburn, M. , Crookston, J. , Long, A.C. , Clifford, M.J. and Jones, I.A. (2008). Finite Element Modelling of Fabric Compression, Modelling and Simulation in Materials Science and Engineering, 16: 035010 (1-16).

21.

Lee, S.H. , Yang, M. , Song, Y.S. , Kim, S.Y. and Youn, J.R. (2009). Three-Dimensional Flow Simulation of Resin Transfer Molding Utilizing Multilayered Fiber Preform , Journal of Applied Polymer Science, 114: 1803-1812.

22.

Li, M. , Gu, Y. , Zhang, Z. and Sun, Z. ( 2007). A Simple Method for the Measurement of Compaction and Corresponding Transverse Permeability of Composite Prepregs, Polymer Composites, 27(1): 61-70.

23.

Servais, C. , Michaud, V. and Manson, J.-A.E. (2001). The Packing Stress of Impregnated Fiber Mats, Polymer Composites, 22(2): 298-311.

24.

Gutowski, T.G. , Cai, Z. and Morigaki, T. (1987). The Consolidation of Laminate Composites, Journal of Composite Materials, 21: 172-188.

25.

Lekakou, C. , Johari, M. and Bader, M.G. (1996). Compressibility and Flow Permeability of Two-dimensional Woven Reinforcements in the Processing of Composites, Polymer Composites, 17(5): 666-672.

26.

Chae, H.S. , Song, Y.S. and Youn, J.R. ( 2007). Transverse Permeability Measurement of a Circular Braided Preform in Liquid Composite Molding, Korea-Australia Rheology Journal, 19(1): 17-25.

27.

Breard, J. , Henzel, Y. , Trochu, F. and Gauvin, R. ( 2003). Analysis of Dynamic Flows Through Porous Media. Part II: Deformation of a Double-scale Fibrous Reinforcement, Polymer Composites, 24(3): 409-421.

28.

Lin, Y.H. ( 2003). Polymer Viscoelasticity: Basics, Molecular Theories and Experiment, World Scientific Publishing Co., Ltd, New York.

29.

Gutowski, T.G. , Cai, Z. , Bauer, S. , Boucher, D. , Kingery, J. and Wineman, S. (1987). Consolidation Experiments for Laminate Composites, Journal of Composite Materials, 21: 650-669.

30.

Saunders, R.A. , Lekakou, C. and Bader, M.G. (1999). Compression in the Processing of Polymer Composites 2. Modeling of the Viscoelastic Compression of Resin-impregnated Fibre Networks, Composites Science and Technology, 59: 1483-1494.

31.

Hankuk Fiber Glass Data Sheet. Available at: http://hfg.fiber-x.com (accessed April 20, 2010).

32.

Breiling, K.B. and Adams, D.O. (1996). Effects of Layer Nesting on Compression-loaded 2-D Woven Textile Composites, Journal of Composite Materials, 30(15): 1710-1728.

33.

Correia, N.C. , Robitaille, F. , Long, A.C. , Rudd, C.D. , Simacek, P. and Advani, S.G. (2005). Analysis of the Vacuum Infusion Moulding Process: I. Analytical Formulation, Composites Part A: Applied Science and Manufacturing, 36: 1645-1656.

34.

Eng, K.M. , Mariatti, M. , Wagiman, N.R. and Beh, K.S. (2006). Effect of Different Woven Linear Densities on the Properties of Polymer Composites, Journal of Reinforced Plastics and Composites, 25(13): 1375-1383.

35.

Kelly, P.A. , Umer, R. and Bickerton, S. (2006). Viscoelastic Response of Dry and Wet Fibrous Materials during Infusion Processes, Composites Part A: Applied Science and Manufacturing, 37(6): 868-873.

36.

Ouagne, P. , Bréard, J. , Ouahbi, T. , Park, C.H. , Saouab, A. and Chatel, S. ( 2008). Hydromechanical Loading and Compressibility of Fibrous Reinforcements, International Journal of Material Forming , 1: 933-936.

37.

Endruweit, A. , Gehrig, S. and Ermanni, P. (2003). Mechanisms of Hydrodynamically Induced In-plane Deformation of Reinforcement Textiles in Resin Injection Processes, Journal of Composite Materials, 37(18): 1675-1692.

38.

Lomov, S.V. , Verpoest, I. , Peeters, T. , Roose, D. and Zako, M. (2003). Nesting in Textile Laminates: Geometrical Modelling of the Laminate, Composites Science and Technology, 63(7): 993-1007.

39.

Bickerton, S. , Sozer, E.M. , Graham, P.J. and Advani, S.G. (2000). Fabric Structure and Mold Curvature Effects on Preform Permeability and Mold Filling in the RTM Process, Composites Part A: Applied Science and Manufacturing , 31(5): 423-438.

40.

Song, Y.S. and Youn, J.R. ( 2006). Asymptotic Expansion Homogenization of Permeability Tensor for Plain Woven Fabrics, Composites Part A: Applied Science and Manufacturing, 37(11): 2080-2087.

41.

Song, Y.S. and Youn, J.R. ( 2007). Flow Advancement through Multi-layered Preform with Sandwich Structure, Composites Part A: Applied Science and Manufacturing , 38: 1082-1088.