In this study, Al-4 wt%Cu alloy and its composites reinforced with different initial particle sizes of ZrC (8 µm and 157 µm) and TiC (13 µm and 93 µm) were fabricated by impulse atomization, and the microstructure of composite and unreinforced alloy droplets were examined by scanning electron microscopy, x-ray diffraction and cell size analyses. Scanning electron microscopic observations of composite droplets indicated that fine ZrC particles (8 µm) were mostly clustered while the other composites of the present investigation were distributed rather uniformly within the fine microstructure of droplets. The relationship between the cell size and the amount of carbide particles reveals that the presence of carbide particles in the alloy powders yields a finer structure. This could be due to the role of the carbide particles as heterogeneous sites for nucleation and to some extent due to particle restricted growth of matrix cells during solidification.
LeeKBKimHSKwonH. Reaction products of Al/TiC composites fabricated by the pressureless infiltration technique. Mater Trans2005; 36A(9): 2517–2527.
2.
KennedyARKarantzalisAE. The incorporation of ceramic particles in molten aluminum and the relationship to contact angle data. Mater Sci Eng A1999; 264(1–2): 122–129.
3.
KennedyARWyattSM. Characterizing particle–matrix interfacial bonding in particulate Al–TiC MMCs produced by different methods. Composites A2001; 32(3–4): 555–559.
4.
GaoMFengCRWeiRP. An analytical electron microscopy study of constituent particles in commercial 7075-T6 and 2024-T3 alloys. Metall Mater Trans A1998; 29A(4): 1145–1151.
5.
IbrahimIAMohamedFALaverniaEJ. Particulate reinforced metal matrix composites-a review. J Mater Sci1991; 26(5): 1137–1156.
6.
SrivastavaVCSchneiderAUhlenwinkelV. Spray processing of 2014 Al+SiCp composites and their property evaluation. Mater Sci Eng A2005; 412(1–2): 19–26.
7.
YangBWangFZhangJS. Microstructural characterization of in-situ TiC/Al and TiC/Al-20Si-5Fe-3Cu-1Mg composites prepared by spray deposition. Acta Mater2003; 51(17): 4977–4989.
8.
GuptaMLaverniaEJ. Effect of atomization on the distribution of SiC particulates in spray deposited Al-7Si/SiC metal matrix composites. J Mater Sci Lett1995; 14(21): 1543–1545.
9.
YangBWangFCuiH. TiC particulate reinforced Al-20Si-5Fe composite fabricated by melt in situ reaction spray forming. J Mater Proc Tech2003; 137(1–3): 187–190.
10.
SrivastavaVCOjhaSN. Microstructure and electrical conductivity of Al-SiC composites produced by spray forming process. Bull Mater Sci2005; 28(2): 125–130.
11.
EslamianMRakJAshgrizN. Preparation of aluminum/silicon metal matrix composites using centrifugal atomization. Powder Tech2008; 184(1): 11–20.
12.
HeneinH. Single fluid atomization through the application of impulses to a melt. Mater Sci Eng A2002; 326(1): 92–100.
13.
PrasadAHeneinH. Droplet cooling in atomization sprays. J Mater Sci2008; 43(17): 5930–5941.
14.
Yuan D, Henein H and Fallavollita JA. Method of producing droplets. US patent 5. 609. 919, 1997.
15.
BadmosAHeneinHIveyDG. Impulse atomized and ingot chip magnesium alloy: Microstructural comparison. Int J Powder Metall2003; 39(2): 39–52.
16.
KaftelenHÜnlüNGöllerG. Comparative processing-structure-property studies of Al-Cu composites reinforced with TiC particulates. Composites: Part A2011; 42(7): 812–824.
17.
MPIF standard 05. Method for determination of sieve analysis of metal powders. Metal Powder Industries Federation, Princeton, NJ, 1990.
18.
ConlonKTMaireEWilkinsonDS. Processing and microstructural characterization of Al-Cu alloys produced from rapidly solidified powders. Metall Mater Trans A2000; 31A(1): 249–260.
19.
LloydDJ. The solidification microstructures of particulate reinforced Al/SiC, composites. Comp Sci Technol1989; 35(2): 159–179.
20.
Dutta B. Studies on particle distribution and matrix microstructure evolution during processing of Al-Cu-SiC composites. PhD Thesis, Banglore, India, 1996.
21.
YuleAJDunkleyJJ. Atomization of melts for powder production and spray deposition, Oxford series on advanced manufacturing, Vol. 11. Oxford: Clarendon Press.
22.
BrookRJ. Concise encyclopedia of advanced ceramic materials, New York, Oxford: Pergamon Press, 1991, pp. 393–393.
23.
LeonCALopezVHBedollaE. Wettability of TiC by commercial aluminum alloy. J Mater Sci2002; 37(16): 3509–3514.
24.
FrouminNFrageNPolakM. Wetting phenomena in the TiC/(Cu–Al) system. Acta Mater2000; 48: 1435–1435.
25.
FrageNFrouminNDanielMP. Wetting of TiC by non-reactive liquid metals. Acta Mater2002; 50(2): 237–245.
26.
NaidichJV. Progress in surface and membrane science, Vol. 14. New York: Academic Press, 1981, pp. 353–484.
27.
ContrerasA. Wetting of TiC by Al-Cu alloys and interfacial characterization. J Colloid Inter Sci2007; 311(1): 159–170.
28.
WiskelJBHeneinHMaireE. Solidification study of aluminum alloys using impulse atomization: Part I: Heat transfer analysis of an atomized droplet. Can Metall Quar2002; 41(2): 97–110.
29.
KaftelenHÖveçoğluMLHeneinH. ZrC particle reinforced Al–4 wt.% Cu alloy composites fabricated by mechanical alloying and vacuum hot pressing: Microstructural evaluation and mechanical properties. Mater Sci Eng A2010; 527(21–22): 5930–5938.
30.
RussellKCCornieJAOhSY. Interfaces in metal matrix composites, Warrendale, PA: AIME, 1986, pp. 61–91.
31.
International Center for Diffraction Data (ICDD). Card no. 4–0787, Database Ed., Joint Committee on Powder Diffraction Standards (JCPDS), Germany, 2006.
32.
International Center for Diffraction Data (ICDD). Card no.71-5027, Database Ed., Joint Committee on Powder Diffraction Standards (JCPDS), Germany, 2006.
33.
International Center for Diffraction Data (ICDD). Card no. 32-1383, Database Ed., Joint Committee on Powder Diffraction Standards (JCPDS), Germany, 2006.
34.
International Center for Diffraction Data (ICDD). Card no. 35–0784, Database Ed., Joint Committee on Powder Diffraction Standards (JCPDS), Germany, 2006.
35.
International Center for Diffraction Data (ICDD) (2006).Card no. 48-1385, Database Ed., Joint Committee on Powder Diffraction Standards (JCPDS), Germany, 2006.
36.
Anita M. Al/C metal matrix composites and boundary surface Characterization. PhD Thesis, Anthony Kerpely Material Sciences and Technologies graduate school, 2004 (in Hungarian).
37.
KaptayGAkmedovSNBorisoglebskiVYu. Thermodynamic properties of metal-like refractory compounds and their intermetallics with aluminium (in Russian). Latv PSR Zinat Akad Vestis Kim Ser1989; 2: 174–181.
38.
Karantzalis AE. Personal communication, 26 May 2010.
39.
ZhangSZhaoYChenG. Microstructures and dry sliding wear properties of in situ (Al3Zr + ZrB2)/Al composites. J Mater Process Technol2007; 184(1–3): 201–208.
40.
AzevedoGSantosDB. Synthesis and characterization of aluminium-zirconium intermetallic composites. J Mater Synt Proc2000; 8(2): 101–108.
41.
KobashiMChohTHoribeY. Effect of alloying elements on ZrC particulate dispersion in liquid aluminium. J Jpn Inst Met1990; 54(8): 933–940.
Robson JD. A new model for prediction of dispersoid precipitation in aluminium alloys containing zirconium and scandium. Acta Mater 2004; 52(6): 1409–1421.
44.
LopezVHScolesAKennedyAR. The thermal stability of TiC particles in an Al7Si wt.%Si alloy. Mater Sci Eng A2003; 356(2003): 316–325.
45.
International Center for Diffraction Data (ICDD). Card no.04-0836, Database Ed., Joint Committee on Powder Diffraction Standards (JCPDS), Germany, 2006.
46.
International Center for Diffraction Data (ICDD). Card no. 02-0173, Database Ed., Joint Committee on Powder Diffraction Standards (JCPDS), Germany, 2006.
47.
ParkJKLucasJP. Moisture effect on SiCp/6061 Al MMC: Dissolution of interfacial Al4C3. Scripta Mater1997; 37(4): 511–516.
48.
KosolapovaTY. Carbides properties, production and applications, 1st edn. New York, NY: Plenium Press, 1971, pp. 250–254.
49.
IsekiTKamedaTMaruyamaT. Interfacial reactions between SiC and Aluminum during joining. J Mater Sci1984; 19(5): 4729–4735.
50.
Rodriguez ReyesMPech-CanulMIParga-TorresJR. Development of aluminum hydroxides in Al-Mg-Si/SiC in infiltrated composites exposed to moist air. Ceram Inter2011; 37(7): 2719–2722.
51.
Bower TF, Brody HD and Flemings MC. Measurements of solute redistribution in dendritic solidification. In: Abbaschian R, Brody H and Mortensen A (eds) Proceedings of the Merton C Flemings Symposium on Solidification and Materials Processing, Cambridge, MA, 2001, pp.23–33.
52.
WiskelJBNavelKHeneinH. Solidification study of aluminum alloys using impulse atomization: Part II. Effect of cooling rate on microstructure. Can Metall Quart2002; 41(2): 193–204.
53.
SatoKFlemingsMC. Grain refining of Al-4.5Cu alloy by adding an Al-30TiC master alloy. Metall Mater Trans A1998; 29A(6): 1707–1710.
54.
ToneXC. Fabrication of in situ TiC reinforced aluminum matrix composites Part I: Microstructural characterization. J Mater Sci1998; 33(22): 5365–5374.
55.
JonesH. Rapid solidification of metals and alloys, London, England: Institute of Metals, 1984, pp. 145–156.
56.
StoneICTsakiropoulosP. Cooling rates in gas atomised Al-4wt%Cu alloy. Int J Rapid Solid1992; 7(3): 177–190.
57.
RohatgiPKPasciakKNarendranathCS. Evolution of microstructure and local thermal conditions during directional solidification of A356-SiC particle composites. J Mater Sci1994; 29(20): 5357–5366.
58.
Mannikar S. Solidification and microstructure studies in SiCp dispersed aluminum alloy composites. Dissertation, Department of Metallurgical Engineering, I.I.Sc., India, 1994.
59.
Dolata-GroszADyziaMSlezionaJ. Solidification analysis of AMMCs with ceramic particles. Arc Mater Sci Eng2007; 28(7): 401–404.
