In this study, experimental studies on hole quality and machinability in drilling of unreinforced polyamide (PA6) and reinforced polyamide with 30% of glass fibers (PA66-GF30) using cemented carbide (K20) tool have been carried out. The experiments have been planned as per full factorial design of experiments. The effects of spindle speed, feed rate, and point angle on hole quality such as hole diameter and circularity error; the machinability characteristics such as thrust force and specific cutting coefficient have been analyzed by developing response surface methodology based second-order mathematical models. The parametric analysis shows that the quality of holes can be improved by proper selection of cutting parameters. The analysis also indicates the influence of reinforced fiber on proposed machinability characteristics during drilling of polyamides.
EndoHMaruiE. Small-hole drilling in engineering plastics sheet and its accuracy estimation. Int J Mach Tools Manuf2006; 46: 575–579.
2.
McCrumNGBuckleyCP. Principles of polymer engineering, New York: Oxford University Press, 1997.
3.
LiJXiaYC. The friction and wear properties of thermoplastic PA6 composites filled with carbon fiber. J Thermoplast Compos Mater2010; 23: 337–349.
4.
GaitondeVNKarnikSRMataFDavimJP. Study on some aspects of machinability in unreinforced and reinforced polyamides. J Compos Mater2009; 43(7): 725–739.
5.
MataFReisPDavimJP. Physical cutting model of polyamide composites (PA66 GF30). Mater Sci Forum2006; 514–516: 643–647.
6.
DavimJPMataF. Comparative evaluation of the turning of reinforced and unreinforced polyamide. Int J Adv Manuf Technol2007; 33: 911–914.
7.
GaitondeVNKarnikSRMataFDavimJP. Taguchi approach for achieving better machinability in unreinforced and reinforced polyamides. J Reinf Plast Compos2008; 27: 909–924.
8.
GaitondeVNKarnikSRMataFDavimJP. Modeling and analysis of machinability characteristics in PA6 and PA66 GF30 polyamides through artificial neural network. J Thermoplast Compos Mater2010; 23: 313–336.
9.
MohanNSRamachandraAKulkarniSM. Influence of process parameters on cutting force and torque during drilling of glass–fiber polyester reinforced composites. Compos Struct2005; 71: 407–413.
10.
ClarkRLCravenMDKanderRG. Nylon 66/poly (vinyl pyrrolidone) reinforced composites: 2-bulk mechanical properties and moisture effects. Composites Part A1999; 30(1): 37–48.
11.
Campos RubioJPanzeraTHAbrãoAMFariaPEDavimJP. Effects of high speed in the drilling of glass whisker-reinforced polyamide composites (PA66 GF30): statistical analysis of the roughness parameters. J Compos Mater2011; 45: 1395–1402.
12.
BhattacharyaDHorriganDPW. A study of hole drilling in Kelvar composites. Compos Sci Technol1998; 58: 267–283.
13.
KhashabaUA. Delamination in drilling GFR thermoset composites. Compos Struct2004; 63: 313–327.
14.
TsaoCCHochengH. Effects of special drill bits on drilling-induced delamination of composite materials. Int J Mach Tools Manuf2006; 46(12–13): 1403–1416.
15.
DavimJPRubioJCAbrãoAM. A novel approach based on digital image analysis to evaluate the delamination factor after drilling composite laminates. Compos Sci Technol2007; 67: 1939–1945.
16.
DavimJPReisPLapaVAntonioCC. Machinability study on polyetheretherketone (PEEK) unreinforced and reinforced (GF30) for application in structural components. Compos Struct2003; 62: 67–73.
17.
AoyamaENobeHHirogakiT. Drilled hole damage of small diameter in printed wiring board. J Mater Process Technol2001; 118: 436–441.
18.
PalanikumarKKarunamoorthyLManoharanN. Mathematical model to predict the surface roughness on the machining of glass fiber reinforced polymer composites. J Reinf Plast Compos2006; 25: 407–417.
19.
GuuHHochengHTaiNHLiuSY. Effect of electrical discharge machining on the characteristics of carbon fiber reinforced carbon composites. J Mater Sci2001; 36: 2037–2043.
20.
PerssonEErikssonIZackrissonL. Effect of hole machining defects on strength and fatigue life of composite laminates. Composites Part A1997; 28(2): 141–151.
21.
LinSCChenIK. Drilling of carbon fiber-reinforced composite material at high speed. Wear1996; 194: 156–162.
22.
GaitondeVNKarnikSRRubioJCCorreiaAEAbrãoAMDavimJP. Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites. J Mater Process Technol2008; 203: 431–438.
23.
KarnikSRGaitondeVNRubioJCCorreiaAEAbrãoAMDavimJP. Delamination analysis in high-speed drilling of carbon fiber reinforced plastics (CFRP) using artificial neural network model. Mater Des2008; 29: 1768–1776.
24.
KrishnarajVPrabhukarthiARamanathanA. Optimisation of machining parameters at high speed drilling of carbon fiber reinforced plastic (CFRP) laminates. Composites Part B2012; 43: 1791–1799.
25.
TsaoCCHochengH. Evaluation of thrust force and surface roughness in drilling composite material using Taguchi analysis and neural network. J Mater Process Technol2008; 203: 342–348.
26.
ZitouneRKrishnarajVCollombetF. Study of drilling of composite material and aluminium stack. Compos Struct2010; 92(5): 1246–1255.
27.
MontgomeryDC. Design and analysis of experiments, New York: John Wiley and Sons, 2003.
28.
AbrãoAMFariaPECampos RubioJCReisPDavimJP. Drilling of fiber reinforced plastics: a review. J Mater Process Technol2007; 186: 1–7.
29.
TondonSJainVKKumarPRajurkarP. Investigations into machining of composites. Precis Eng1990; 12(4): 227–238.
30.
RahmanMRamakrishnanSPrakashJRSTenDCG. Machinability study of carbon fiber reinforced composite. J Mater Process Technol1999; 89–90: 292–297.
31.
BasavarajappaSVenkateshAGaitondeVNKarnikSR. Experimental investigations on some aspects of machinability in drilling of glass epoxy polymer composites. J Thermoplast Compos Mater2012; 25(3): 63–387.
32.
VelayudhamAKrishnamurthyRSoundarapandianT. Evaluation of drilling characteristics of high volume fraction fiber glass reinforced polymeric composite. Int J Mach Tools Manuf2005; 45: 399–406.
33.
LangellaANeleLMaioA. A torque and thrust prediction model for drilling of composite materials. Composites Part A2005; 36: 83–93.
34.
VelayudhamAKrishnamurthyR. Effect of point geometry and their influence on thrust and delamination in drilling of polymeric composites. J Mater Process Technol2007; 185: 204–209.
35.
Campos RubioJAbraoAMFariaPEEsteves CorreiaADavimJP. Effects of high speed in the drilling of GFRP: evaluation of the delamination factor. Int J Mach Tools Manuf2008; 48: 715–720.
