The paper presents a comparison of the test results for the fiber volume fraction, static bending and Charpy impact strength of glass fiber reinforced polymer laminates reinforced by 0/90 fabric and chopped strand mat, produced by the hand lay-up and the vacuum-assisted resin infusion (VARI) method. The laminates were produced under equivalent conditions, with polyester matrix and lay-up areal mass 2100 g/m2. In the comparison of the obtained measurement results, similar mechanical performance was stated in the case of the hand lay-up and the VARI production. However, significantly smaller scatter of results and better uniformity of the reinforcement in the matrix with smaller amount of local structure defects was observed for the samples obtained by VARI method. The laminates obtained by VARI method show a much more advantageous coefficient of variation than that of the hand lay-up method, especially in the case of the mat reinforcement.
BrouwerWDVan HerptECFCLabordusM. Vacuum injection moulding for large structural applications. Compos Part A: Appl Sci Manuf2003; 34: 551–558.
4.
LightfootJSWisnomMRPotterK. Defects in woven preforms: Formation mechanisms and the effects of laminate design and layup protocol. Compos Part A: Appl Sci Manuf2013; 51: 99–107.
SeyhanAT. A statistical study of fatigue life prediction of fibre reinforced polymer composites. Polym Polym Compos2011; 9: 717–724.
7.
KoziolMSlezionaJ. Failure progress of stitched reinforced polyester-glass laminate at static bending. Polimery2008; 11-12: 502–508.
8.
KoziolM. Experimental study on the effect of stitch arrangement on mechanical performance of GFRP laminates manufactured on a basis of stitched preforms. J Compos Mater2012; 9: 1067–1078.
9.
KoziolM. Effect of thread tension on mechanical performance of stitched glass fibre-reinforced polymer laminates – experimental study. J Compos Mater2013; 16: 1919–1930.
Bogdan-WlodekAKoziolMMyalskiJ. Influence of surface treatment on the wetting process of jute fibres with thermosetting polyester resin. Polish J Chem Technol2012; 1: 21–27.
12.
KoziolMBogdan-WlodekAMyalskiJ. Influence of wet chemistry treatment on the mechanical performance of natural fibres. Polish J Chem Technol2011; 4: 21–27.
13.
KoziolMWieczorekJBogdan-WlodekA. Evaluation of jute fiber preforms absorbability using optical profilographometer. J Compos Mater2013; 47: 2309–2319.
14.
HufenbachWAGudeMAdamF. Experimental investigation of composite-based compliant structures. Kompozyty2011; 3: 187–191.
15.
Press article: Scottsdale library is first building designed with PPG’s new VARI Cool coatings. Focus on Powder Coatings, Issue 6, 2010.
16.
HufenbachWBohmRBlazejewskiW. Manufacture, design and testing of piping elements from braided composites. Chem Eng Technol2005; 7: 808–813.
17.
FerreiraAJMRoqueCMCNevesAMA. Buckling and vibration analysis of isotropic and laminated plates by radial basis functions. Compos Part B: Eng2011; 3: 592–606.
18.
WenPHAliabadiMH. Damage mechanics analysis of plain woven fabric composite micromechanical model for mesh-free simulations. J Compos Mater2012; 18: 2239–2253.
19.
StellerR. Free volume effect on behavior of polymer liquids in shear flows. Polimery2012; 7-8: 562–570.
20.
RieberGJiangJDeterC. Influence of textile parameters on the in-plane permeability. Compos Part A: Appl Sci Manuf2013; 52: 89–98.
21.
DeValveCPitchumaniR. Simulation of void formation in liquid composite molding processes. Compos Part A: Appl Sci Manuf2013; 51: 22–32.
22.
TrochuFRuizEAchimV. Advanced numerical simulation of liquid composite molding for process analysis and optimization. Compos Part A: Appl Sci Manuf2006; 37: 890–902.
23.
NurzynskaKKuboMMuramotoK. Texture operator for snow particle classification into snowflake and graupel. Atmos Res2012; 118: 121–132.
24.
SorrentinoLBelliniCGereviniE. New methodology to determine the compressibility curve in a RIFT process. J Compos Mater2014; 48(10): 1233–1240.
25.
MakaHSpychajT. Epoxy resin crosslinked with conventional and deep eutectic ionic liquids. Polimery2012; 6: 456–462.
GojnyFHSchulteK. Functionalisation effect on the thermo mechanical behaviour of multi-wall carbon nanotube/epoxy-composites. Compos Sci Technol2004; 64: 2303–2308.
28.
NowakT. Experimental and numerical analysis of viscoelastic behavior of epoxy resin with silica filler based on master curve concept. Kompozyty2012; 1: 3–8.
29.
FaghihianHNourmoradiHShokouhiM. Performance of silica aerogels modified with amino functional groups in Pb(II) and Cd(II) removal from aqueous solutions. Polish J Chem Technol2012; 1: 50–56.
30.
LegockaIWierzbickaEAl-ZahariTJM. Modified halloysite as a filler for epoxy resins. Polish J Chem Technol2011; 3: 47–52.
31.
ZhuH-GLeungCKYKimJ-K. Tensile properties degradation of GFRP composites containing nanoclay in three different environments. J Compos Mater2012; 18: 2179–2192.
32.
GrabowskaBBulwanMZapotocznyS. Biodegradation of new polymer foundry binders composition of poly(acrylic acid)/dextrin. Polimery2012; 7–8: 529–534.
33.
Dolata-GroszASlezionaJFormanekB. Structure and properties of aluminium cast composites strengthened by dispersion phases. J Mater Process Technol2006; 175(1–3): 192–197.
34.
Dolata-GroszAFormanekBSlezionaJ. Al-FeAl-TiAl-Al2O3 composite with hybrid reinforcement. J Mater Process Technol2005; 162: 33–38.
35.
FormanekBJozwiakSSzczucka-LasotaB. Intermetallic alloys with ceramic particles and technological concept for high loaded materials. J Mater Process Technol2005; 162: 46–51.
36.
Dolata AJ and Dyzia M. Aspects of fabrication aluminium matrix heterophase composites by suspension method. IOP Conference Series-Materials Science and Engineering, Article Number: 012020.
DyziaMDolataASlezionaJ. Preliminary analysis of aluminum matrix compositions for composites reinforcement with carbon fibers. Steel Res Int2012; 83(10): 981–987.
39.
SlezionaJDyziaMMyalskiJ. The structure and properties of sinters produced from composite powders Al-Al2O3-Al3Fe-Al3Ti. J Mater Process Technol2005; 162: 127–130.
40.
Press article: Simulation software developed for VARI processing. Reinforced Plastics, September 2004.
41.
KoziolMRydarowskiHMyalskiJ. Evaluation of vacuum resin infusion process on selected glass fibre preforms. Kompozyty2012; 4: 285–290.
42.
BraunerCBlockTBPurolH. Microlevel manufacturing process simulation of carbon fiber/epoxy composites to analyze the effect of chemical and thermal induced residual stresses. J Compos Mater2012; 17: 2123–2143.
43.
Feichtinger K, Ma W and Elkin R. Properties of structural sandwich core materials: Hand lay-up vs. vacuum-infusion processing. In: Proceedings of “composites 2006 convention and trade show”, American Composites Manufacturers Association, St. Louis, MO, USA, 18–20 October 2006.
