A cure modelling study of an unsaturated polyester resin system for the simulation of curing of fibre-reinforced composites during the vacuum infusion process
Restricted accessResearch articleFirst published online August, 2015
A cure modelling study of an unsaturated polyester resin system for the simulation of curing of fibre-reinforced composites during the vacuum infusion process
This study presents the cure kinetics and cure modelling of an ambient curing unsaturated polyester (UP) resin system for its cure simulation in the vacuum infusion (VI) process. The curing of the UP resin system was investigated using differential scanning calorimetry (DSC). The dynamic DSC test measurements were conducted to find out the ultimate heat of reaction and enable experimental conversion determination for the isothermal curing. The empirical autocatalytic cure kinetics model incorporating the Arrhenius law represented the cure behaviour. The results of the cure kinetics study, the cure model, the material properties and the boundary conditions were the inputs in PAM-RTM software for the simulation of the degree of cure and the exothermic temperature during the infusion and the room temperature curing stages. The simulation results were compared with experimentally measured data. A vacuum infusion (VI) experiment involving a non-crimp glass fibre preform was performed in order to monitor the curing using thermocouples and validate the temperature simulation result. It was shown that the degree of cure and the exothermic temperature of a room temperature curing thermoset resin system during the VI process could be predicted through the steps of this study.
Ton-ThatMTColeKCJenCK. Polyester cure monitoring by means of different techniques. Polymer Compos2000; 21: 605–618.
2.
UmMKDanielIMHwangBS. A study of cure kinetics by the use of dynamic differential scanning calorimetry. Compos Sci Technol2002; 62: 29–40.
3.
KarkanasPIPartridgeIKAttwoodD. Modelling the cure of a commercial epoxy resin for applications in resin transfer moulding. Polymer Int1996; 41: 183–191.
4.
RabearisonNJochum ChGrandidierJC. A cure kinetics, diffusion controlled and temperature dependent, identification of the Araldite LY556 epoxy. J Mater Sci2011; 46: 787–796.
5.
LeeWILoosACSpringerGS. Heat of reaction, degree of cure, and viscosity of Hercules 3501-6 Resin. J Compos Mater1982; 16: 510–520.
NGHManas-zloczowerI. A nonisothermal differential scanning calorimetry study of the curing kinetics of an unsaturated polyester system. Polymer Eng Sci1989; 29: 1097–1102.
8.
ZetterlundPBJohnsonAF. A new method for the determination of the Arrhenius constants for the cure process of unsaturated polyester resins based on a mechanistic model. Thermocimica Acta1996; 289: 209–221.
9.
CuadradoTRBorrajoJWilliamsRJJ. On the curing kinetics of unsaturated polyesters with styrene. J Appl Polymer Sci1983; 28: 485–499.
10.
RouisonDSainMCouturierM. Resin transfer moulding of natural fibre reinforced plastic. I. Kinetic study of an unsaturated polyester resin containing an inhibitor and various promoters. J Appl Polymer Sci2003; 89: 2553–2561.
11.
RamisXSallaJM. Effect of the inhibitor on the curing of an unsaturated polyester resin. Polymer1995; 36: 3511–3521.
12.
AvellaMMartuscelliEMazzolaM. Kinetic study of the cure reaction of unsaturated polyester resins. J Therm Anal1985; 30: 1359–1366.
13.
MartinJL. Kinetic analysis of two DSC peaks in the curing of an unsaturated polyester resin catalysed with methylethylketone peroxide and cobalt octoate. Polymer Eng Sci2007; 47(1): 62–70.
14.
YunYMLeeSJLeeKJ. Composite cure kinetic analysis of unsaturated polyester free radical polymerisation. J Polymer Sci: Part B: Polymer Phys1997; 35: 2447–2456.
15.
BoyardNSinturelCVayerM. Morphology and cure kinetics of unsaturated polyester resin/block copolymer blends. J Appl Polymer Sci2006; 102: 149–165.
16.
YousefiALafleurPGGauvinR. The effects of cobalt promoter and glass fibres on the curing behaviour of unsaturated polyester resin. J Vinyl Additives Technol1997; 3: 157–169.
17.
YousefiALafleurPGGauvinR. Kinetic studies of thermoset cure reactions: a review. Polymer Compos1997; 18(2): 157–168.
18.
MartinJLCadenatoASallaJM. Comparative studies on the non-isothermal DSC curing kinetics of an unsaturated polyester resin using free radicals and empirical models. Thermochimica Acta1997; 306: 115–126.
19.
GaoJDongCDuY. Nonisothermal curing kinetics and physical properties of unsaturated polyester modified with EA-POSS. Int J Polymeric Mater2010; 59: 1–14.
20.
VilasJLLazaJMGarayMT. Unsaturated polyester resins cure: Kinetic, rheologic, and mechanical-dynamical analysis. I. Cure Kinetics by DSC and TSR. J Appl Polymer Sci2001; 79: 447–457.
21.
Laurent-MounierABinetruyCKrawczakP. Multipurpose carbon fibre sensor design for analysis and monitoring of the resin transfer moulding of polymer composites. Polymer Compos2005; 26(5): 717–730.
22.
EumSHKageyamaKMurayamaH. Structural health monitoring using fibre optic distributed sensors for vacuum-assisted resin transfer moulding. Smart Mater Struct2007; 16: 2627–2635.
BangKGKwonJWLeeDG. Measurements of the degree of cure of glass fibre-epoxy composites using dielectrometry. J Mater Process Technol2001; 113: 209–214.
25.
KobayashiSMatsuzakiRTodorokiA. Multipoint cure monitoring of CFRP laminates using a flexible matrix sensor. Compos Sci Technol2009; 69: 378–384.
26.
HsiaoKTLittleRRestrepoO. A study of direct cure kinetic characterisation during liquid composite moulding. Compos: Part A: Appl Sci Manuf2006; 37: 925–933.
27.
ChiuHTYuBChenSC. Heat transfer during flow and resin reaction through fibre reinforcement. Chem Eng Sci2000; 55: 3365–3376.
28.
RouisonDSainMCouturierM. Resin transfer moulding of natural fibre reinforced composites: cure simulation. Compos Sci Technol2004; 64: 629–644.
KiunaNLawranceCJFontanaQPV. A model for resin viscosity during cure in the resin transfer moulding process. Compos Part A: Appl Sci Manuf2002; 33: 1497–1503.
31.
BlestDCDuffyBRMcKeeS. Curing simulation of thermoset composites. Compos: Part A: Appl Sci Manuf1999; 30: 1289–1309.
32.
JoshiSCLiuXLLamYC. A numerical approach to the modelling of polymer curing in fibre-reinforced composites. Compos Sci Technol1999; 59(7): 1003–1013.
HickeyCMDBickertonS. Cure kinetics and rheology characterisation and modelling of ambient temperature curing epoxy resins for resin infusion/VARTM and wet layup applications. J Mater Sci2013; 48: 690–701.
35.
SeifiRHojjatiM. Heat of reaction, cure kinetics, and viscosity of Araldite LY-556 resin. J Compos Mater2005; 39.
36.
DusiMRLeeWICiriscioliPR. Cure kinetics and viscosity of Fiberite 976 resin. J Compos Mater1987; 27: 243–261.
Aktas A, Boyd SW and Shenoi RA. Monitoring and simulation of the vacuum infusion process. In: International conference on composite materials, Montreal, Canada, 28 July to 2 August 2013.
