Rapid curing vacuum-assisted resin infusion molding using silicone rubber sheet heater and the effect of cooling process on the properties of carbon fiber/epoxy composites
Restricted accessResearch articleFirst published online June, 2016
Rapid curing vacuum-assisted resin infusion molding using silicone rubber sheet heater and the effect of cooling process on the properties of carbon fiber/epoxy composites
Silicone rubber sheet heater-aided vacuum-assisted resin infusion molding was developed in order to shorten curing cycle time. Three kinds of cooling methods, including air cooling, air water cooling, and water cooling, were employed; the effects of cooling process on processing time, residual strains, and mechanical properties were experimentally studied. The residual strains generated in cooling stage were monitored by embedded strain gauges. The results showed that in order to avoid serious residual strains and lower mechanical properties, the cooling rate of the silicone rubber sheet heater-aided vacuum-assisted resin infusion molding process should be designed carefully. Slow cooling rate before glass transition temperature of the composites and rapid cooling rate after it might be a practical method to maintain both high processing efficiency and acceptable mechanical properties.
ZhangJinChaisombatKhunlavitHeShuai. Hybrid composite laminates reinforced with glass/carbon woven fabrics for lightweight load bearing structures. Mater Des2012; 36: 75–80.
2.
KlausFAlmajidAA. Manufacturing aspects of advanced polymer composites for automotive applications. Appl Compos Mater2013; 20: 107–128.
3.
ZhangKGuYLiM. Effect of rapid curing process on the properties of carbon fiber/epoxy composite fabricated using vacuum assisted resin infusion molding. Mater Des2014; 54: 624–631.
4.
YenilmezBMurat SozerE. Compaction of e-glass fabric preforms in the vacuum infusion process: (a) use of characterization database in a model and (b) experiments. J Compos Mater2013; 47: 1959–1975.
5.
AurrekoetxeaJAgirregomezkortaAAretxagaG. Impact behavior of carbon fiber/epoxy composite manufactured by vacuum-assisted compression resin transfer molding. J Compos Mater2012; 46: 43–49.
6.
BrouwerWDVan HerptELabordusM. Vacuum injection moulding for large structural applications. Compos Part A2003; 34: 551–558.
7.
GriffithsBNobleN. Process and tooling for low cost, rapid curing of composite structures. SAMPE J2004; 40: 41–46.
8.
Hodgkin JH and Rabu N. A new development in high-speed composite fabrication. In: Proceedings of the 45th international SAMPE symposium, Longbeach, CA, 2000, pp.2274–2282. Covina: SAMPE.
9.
Coenen V, Hatrick M, Law H, et al. A feasibility study of Quickstep processing of an aerospace composite material. In: SAMPE Europe 26th international conference, Paris, 2005, pp.470–475. Oerlingen: SAMPE.
10.
DaviesLWDayRJBondD. Effect of cure cycle heat transfer rates on the physical and mechanical properties of an epoxy matrix composite. Compos Sci Technol2007; 67: 1892–1899.
11.
HerringMLFoxBL. The effect of a rapid curing process on the surface finish of a carbon fiber epoxy composite. Compos Part B2011; 42: 1035–1043.
12.
ZhuLPitchumaniR. Analysis of a process for curing composites by the use of embedded resistive heating elements. Compos Sci Technol2000; 60: 2699–2712.
13.
StephenASDonaldJL. Consolidation of U-Nyte epoxy-coated carbon-fiber composites via temperature controlled resistive heating. J Compos Mater2008; 42: 2551–2566.
14.
AthanasopoulosNKostopoulosV. Resistive heating of multidirectional and unidirectional dry carbon fibre preforms. Compos Sci Technol2012; 72: 1273–1282.
15.
ZhangJFengSY. Temperature effects of electrical resistivity of conductive silicone rubber filled with carbon blacks. J Appl Polym Sci2003; 90: 3889–3895.
16.
YizhuoGuXingQMinL. The study of temperature distribution and curing property of VARIM process utilizing rapid heating methods. Polym Polym Compos2015; 23: 11–19.
17.
NawabYJaqueminFCasariP. Evolution of chemical and thermal curvatures in thermoset-laminated composite plates during the fabrication process. J Compos Mater2013; 47: 327–339.
18.
ZhuQGeubellePHLiM. Dimensional accuracy of thermoset composites: simulation of process-induced residual stresses. J Compos Mater2001; 35: 2171–2205.
19.
WisnomMRGigliottiMErsoyN. Mechanisms generating residual stresses and distortion during manufacture of polymer-matrix composite structures. Compos Part A2006; 37: 522–529.
20.
WhiteSRHahnHT. Process modeling of composite materials: residual stress development during cure. Part II. Experimental validation. J Compos Mater1992; 26: 2423–2453.
21.
RadfordDWDiefendorfRJ. Shape instabilities in composites resulting from laminate anisotropy. J Reinf Plast Compos1993; 12: 58–75.
22.
WiersmaHWPeetersLJBAkkermanR. Prediction of spring forward in continuous-fiber/polymer L-shaped parts. Compos Part A1998; 29: 1333–1342.
23.
ErsoyNPotterKWisnomMR. Development of spring-in angle during cure of a thermosetting composite. Compos Part A2005; 36: 1700–1706.
24.
GigliottiMWisnomMRPotterKD. Development of curvature during the cure of AS4/8552 0/90. unsymmetric composite plates. Compos Sci Technol2003; 63: 187–197.
25.
FernlundGRahmanNCourdjiR. Experimental and numerical study of the effect of cure cycle, tool surface, geometry, and lay-up on the dimensional fidelity of autoclave-processed composite parts. Compos Part A2002; 33: 341–351.
26.
PotterKDCampbellMLangerC. The generation of geometrical deformations due to tool/part interaction in the manufacture of composite components. Compos Part A2005; 36: 301–308.
27.
de OliveiraRSLavanchyRChattonD. Experimental investigation of the effect of the mould thermal expansion on the development of internal stresses during carbon fibre composite processing. Compos Part A2008; 39: 1083–1090.
28.
RuizETrochuF. Numerical analysis of cure temperature and internal stresses in thin and thick RTM parts. Compos Part A2005; 36: 806–826.
29.
DarrowDAJrSmithLV. Isolating components of processing induced warpage in laminated composites. J Compos Mater2002; 36: 2407–2419.
30.
SvanbergJM. An experimental investigation on mechanisms for manufacturing induced shape distortions in homogeneous and balanced laminates. Compos Part A2001; 32: 827–838.
31.
van RijswijkKTeuwenJJEBerseeHEN. Textile fiber-reinforced anionic polyamide-6 composites. Part I: the vacuum infusion process. Compos Part A2009; 40: 1–10.
32.
TwiggGPoursartipAFernlundG. An experimental method for quantifying tool-part shear interaction during composites processing. Compos Sci Technol2003; 63: 1985–2002.
33.
AntonucciVCusanoAGiordanoM. Cure-induced residual strain build-up in a thermoset resin. Compos Part A2006; 37: 592–601.
34.
KimSSMurayamaHKageyamaK. Study on the curing process for carbon/epoxy composites to reduce thermal residual stress. Compos Part A2012; 43: 1197–1202.
35.
Alavi-SoltaniSSabzevariSKoushyarH. Thermal, rheological, and mechanical properties of a polymer composite cured at different isothermal cure temperatures. J Compos Mater2012; 46: 575–587.
36.
RossiniNSDassistiMBenyounisKY. Methods of measuring residual stresses in components. Mater Des2012; 35: 572–588.
37.
KantarosAKaralekasD. Fiber Bragg grating based investigation of residual strains in ABS parts fabricated by fused deposition modeling process. Mater Des2013; 50: 44–50.
38.
WhiteSRHahnHT. Cure cycle optimization for the reduction of processing induced residual stresses in composite materials. J Compos Mater1993; 27: 1352–1378.
39.
MulleMCollombetFOlivierP. Assessment of cure residual strains through the thickness of carbon-epoxy laminates using FBGs, Part I: elementary specimen. Compos Part A2009; 40: 94–104.
40.
HodgesJYatesBDarbyMI. Residual stresses and the optimum cure cycle for an epoxy resin. J Mater Sci1989; 24: 1984–1990.
41.
AspLBerglundLATalrejaR. Effects of fibre and interface on matrix initiated transverse failure in polymer composites. Compos Sci Technol1996; 56: 657–665.
42.
SjogrenAJoffeRBerglundL. Effects of fiber coating (size) on properties of glass fiber vinyl ester composites. Compos Part A1999; 30: 1009–1015.
43.
WangXZhangJWangZ. Effects of interphase properties in unidirectional fiber reinforced composite materials. Mater Des2011; 32: 3486–3492.
