A study is described in which the mode I, mode II, and mixed-mode delamination toughnesses of a woven fabric graphite/polyimide composite are determined at room temperature and at 300℃. It is shown that, with some modifications, commonly used delamination toughness test methods can be extended for use into this relatively high-temperature regime. At room temperature, the mode II toughness was found to be significantly higher than that obtained in mode I. Relative to their fracture toughnesses at room temperature, the mode I and mixed-mode toughnesses increased at elevated temperature, while the mode II toughness decreased. Thus, at 300℃, the mode I toughness was larger than that obtained for mode II. The temperature dependence in all three modes was found to be consistent with what is predicted based on micromechanical considerations for the effects of temperature on the resin. In addition, the local tow orientations influenced the fracture path and produced toughening mechanisms that were both temperature and mode mix dependent.
Thesken JC, et al. Thermomechanical fatigue of polyimide composites in reusable propulsion systems. In: International SAMPE technical conference, Long Beach, CA, 2004.
2.
Shin EE, et al. Effects of fiber reinforcement architecture on the hygrothermal-mechanical performance of polyimide matrix composites for aeropropulsion applications. In: Proceedings of ICCM-14, San Diego, CA, 2003.
3.
Bowman CL, et al. Graphite fiber/polyimide composites subjected to moisture and rapid heating. In: Rasmussen BM, Pilato L and Kliger HS (eds) Proceedings of the 47th international SAMPE symposium and exhibition, Covina, CA, 2002, pp.1–11.
4.
DavidsonBDKumarMSoffaMA. Influence of mode ratio and hygrothermal conditions on the delamination toughness of thermoplastic particulate interlayered carbon/epoxy composite. Composites Part A2009; 40: 67–79.
LeeSM. Mode II delamination failure mechanisms of polymer matrix composites. J Mater Sci1997; 32: 1287–1295.
7.
KimJKShamML. Impact and delamination failure of woven-fabric composites. Compos Sci Technol2000; 60: 745–761.
8.
GreenhalghES. Failure analysis and fractography of polymer composites, Cambridge, UK: Woodhead Publishing, 2009, pp. 303–315.
9.
AlifNCarlssonLABooghL. The effect of weave pattern and crack propagation direction on mode I delamination resistance of woven glass and carbon composites. Composites Part B1998; 29: 603–611.
10.
SuppakulPBandyopadhyayS. The effect of weave pattern on the mode-I interlaminar fracture energy of E-glass/vinyl ester composites. Compos Sci Technol2002; 62: 709–717.
11.
EbelingTHiltnerABaerE. Delamination failure of a woven glass fiber composite. J Compos Mater1997; 31: 1318–1333.
12.
ShinSJangJ. Fractographical analysis of the mode II delamination in woven carbon fiber reinforced epoxy composites. J Mater Sci1999; 34: 5299–5306.
NaikNK. Interlaminar fracture characterization for plain weave fabric composites. J Mater Sci2002; 37: 2983–2987.
15.
KimKYYeL. Interlaminar fracture toughness of CF/PEI composites at elevated temperatures: roles of matrix toughness and fibre/matrix adhesion. Composites Part A2004; 35: 477–487.
16.
KimKYYeLPhoaKM. Interlaminar fracture toughness of CF/PEI and GF/PEI composites at elevated temperatures. Appl Compos Mater2004; 11: 173–190.
17.
Alif N, Carlsson LA and Gillespie JW Jr. Mode I, mode II and mixed mode interlaminar fracture of woven fabric carbon/epoxy. In: Hooper SJ (ed.) Composite materials: testing and design. vol. 13. ASTM STP 1242, pp.82–106.
18.
FrassineRPavanA. Viscoelastic effects on the interlaminar fracture behaviour of thermoplastic matrix composites. I. Rate and temperature dependence in unidirectional PEI/carbon-fibre laminates. Compos Sci Technol1995; 54: 193–200.
19.
Chuang KC, Papadopoulos DS and Arendt CP. High Tg polyimide composites II. In: Proceedings of the 47th International SAMPE symposium and exhibition, Covina, CA, 2002, pp.1175–1186.
20.
ChuangKC. 6F-polyimides with phenylethynyl endcap for 600-700°F applications. High Performance Polym2003; 15: 459–472.
21.
MichaelsTEDavidsonBD. Ultrasonic inspection detects hidden damage in composite materials. Adv Mater Process1993; 143: 34–38.
22.
DavidsonBDTellerSS. Recommendations for an ASTM standardized test for determining GIIc of unidirectional laminated polymeric matrix composites. J ASTM Int2010; 7: 1–11.
23.
Polaha JJ and Davidson BD. Test procedures for determining the delamination toughness of ceramic matrix composites as a function of mode ratio, temperature, and layup. In: Jenkins MG, et al. (eds) Mechanical, thermal and environmental testing and performance of ceramic composites and components, ASTM STP 1392, pp.31–47.
24.
American Society for Testing and Materials. Standard test method for mode I interlaminar fracture toughness of unidirectional fiber-reinforced polymer matrix composites. ASTM Standard D5528-01, 2008.
25.
DavidsonBDSoffaMAKumarM. Temperature and moisture effects in a particulate interlayered composite: mode I data reduction and toughness. J Reinf Plast Compos2009; 28: 2049–2068.
26.
HashemiSKinlochAJWilliamsJG. Mechanics and mechanisms of delamination in a poly(ether sulphone)–fibre composites. Compos Sci Technol1990; 37: 429–462.
27.
American Society for Testing and Materials. Standard test method for mode II interlaminar fracture toughness of unidirectional fiber-reinforced polymer matrix composites, ASTM Standard D7905-14.
28.
DavidsonBDBialaszewskiRDSainathSS. A non-classical, energy release rate based approach for predicting delamination growth in graphite reinforced laminated polymeric composites. Compos Sci Technol2006; 66: 1479–1496.
DavidsonBDSunX. Geometry and data reduction recommendations for a standardized end notched flexure test for unidirectional composites. J ASTM Int2006; 3: 1–19.
31.
Davidson BD. Towards an ASTM standardized test for determining GIIc of unidirectional laminated polymeric matrix composites. In: Mallick PK (ed.) Proceedings of the 21st annual American society for composites technical conference, Deaborn, MI. Lancaster, PA: DEStech Publications.
32.
PerezCLDavidsonBD. Evaluation of precracking methods for the end-notched flexure test. AIAA J2007; 45: 2603–2611.
33.
DavidsonBDSundararamanVA. A single leg bending test for interfacial fracture toughness determination. Int J Fract1996; 78: 193–210.
34.
DavidsonBD. Geometrically nonlinear determination of energy release rate and mode ratio in single leg bending tests. J Reinf Plast Compos2008; 28: 1881–1901.
35.
KotakiMHamadaH. Effect of interfacial properties and weave structure on mode I interlaminar fracture behavior of glass satin woven fabric composites. Composites Part A1997; 28: 257–266.
36.
ShivakumarK. A total fatigue life model for mode I delaminated composite laminates. Int J Fatigue2006; 28: 33–42.
37.
Murri GB and Martin RH. Effect of initial delamination on mode I and mode II interlaminar fracture toughness and fatigue fracture threshold. In: Stinchcomb WW and Asbaugh NE (eds) Composite materials: fatigue and fracture. 4th vol. ASTM STP 1156, pp.239–256.
38.
DavidsonBDKrügerRKönigM. Three dimensional analysis and resulting design recommendations for unidirectional and multidirectional end-notched flexure tests. J Compos Mater1995; 29: 2108–2133.
39.
LeeSM. Mode II interlaminar crack growth process in polymer matrix composites. J Reinf Plast Compos1999; 18: 1254–1266.
