Effect of geometric parameters on the behavior of bolted GFRP pultruded plates

Abstract

This paper presents the effect of geometric parameters on the behavior of bolted glass fibre reinforced polymer (GFRP) pultruded plates for civil engineering applications. After a literature review, results of an experimental analysis investigating the behavior of GFRP-to-steel single-lap bolted connections are presented. Then, a finite element analysis validated by experimental data is used to evaluate the effects of the end-distance, side-distance, pitch, and plate properties on the strength and failure mode of the connection. A critical examination of geometric recommendations proposed in design references is presented. Bearing failure caused by contact of the bolt on the GFRP plate is usually defined as the preferred failure mode. With highly orthotropic plate, this type of failure was found to be less likely to occur when loading is applied in the pultruded direction. The investigation showed that the minimum end-distance and pitch-distance recommended by design references usually produce a connection with the maximum capacity. However, it was found that the minimum side-distance recommended by these references does not necessarily lead to the maximum capacity for one bolt and for two bolt in a column connections.

Keywords

Connection bolt pultruded GFRP single-lap FE analysis failure mode geometric parameters

Get full access to this article

View all access options for this article.

References

ASCE Pre-standard. Pre-standard for load and resistance factor design (LRFD) of pultruded reinforced polymer structure (final). American Society of Civil Engineers, 2010, pp.67–84.

Clarke

. EUROCOMP design code and handbook, 1st ed. London: E & FN Spon, 1996.

CNR-DT 205/2007. Guide for the design and construction of structures made of FRP pultruded elements. Advisory committee on technical recommendation for construction, http://www.cnr.it/documenti/norme/IstruzioniCNR_DT205_2007_eng.pdf (accessed 16 December 2015).

Strongwell. Strongwell Design Manual. Strongwell Corporation, Bristol, VA, 2002. http://www.strongwell.com/ (accessed 24 December 2015).

Fiberline Composites. The fibreline design manual. Fiberline Composites A/S, Denmark. http://fiberline.com/sites/default/files/media/online-tools/190107_dm_uk.pdf (2003, accessed 24 December 2015).

Creative Pultrusion. The Pultrex Pultrusion Design Manual. Creative Pultrusions Inc., Alum Bank, PA. http://www.creativepultrusions.com/products-solutions/fabrication-capabilities/pultexc2ae-pultrusion-design-manual1/ (2004, accessed 24 December 2015).

Bank

. Composite for construction structural design with FRP materials, Hoboken, New Jersey: John Wiley & Sons, Inc, 2006.

Thoppul

Finegan

Gibson

. Mechanics of mechanically fastened joints in polymer-matrix composite structures – A review. Comp Sci Technol 2008; 69: 301–329.

Mottram

Turvey

. Physical test data for the appraisal of design prcedures for bolted joints in pultruded FRP structural shapes and systems. Prog Struct Eng Mater 2003; 5: 195–222.

10.

Girao Coelho

Mottram

. A review of the behaviour and analysis of bolted connections and joints in pultruded fibre reinforced polymers. Mater Des 2015; 74: 86–107.

11.

Mottram JT. Reference and bibliography database on research and development with pultruded fibre reinforced polymer shapes and systems, http://www2.warwick.ac.uk/fac/sci/eng/staff/jtm/prfp_latest.pdf (2014, accessed 16 December 2015).

12.

Abd-El-Naby

SFM

Hollaway

. The experimental behaviour of bolted joints in pultruded glass/polyester material. Part 1: single-bolt joints. Composites 1993a; 24: 531–538.

13.

Rosner

Rizkalla

. Bolted connections for fibre-reinforced composite structural members: experimental program. J Mater Civil Eng ASCE 1995; 7: 223–231.

14.

Erki

. Bolted glass-fibre-reinforced plastic joints. Can J Civil Eng 1995; 22: 736–744.

15.

Cooper

Turvey

. Effects of joint geometry and bolt torque on the structural performance of single bolt tension joints in pultruded GRP sheet material. Compos Struct 1995; 32: 217–226.

16.

Yuan RL, Liu CJ and Daley T. Study of mechanical connection for GFRP laminated structures. In: Proceedings of 2nd international conference on advanced composite materials in bridges and structures ACMBS-2, 1996, pp.951–958. Whistler: The Canadian Society for Civil Engineers.

17.

Ramaskrishna

Hamada

Nishiwaki

. Bolted joints of pultruded sandwich composite laminates. Compos Struct 1995; 32: 227–235.

18.

Yuan RL and Weyant SE. The effect of environmental exposure of the behavior of pultruded mechanical connections. In: Proceedings of annual conference composite institute, SPI, 1997, Session 14-F.

19.

Turvey

. Single-bolt tension joint tests on pultruded GRP plate: effects of tension direction relative to pultrusion direction. Compos Struct 1998; 42: 341–351.

20.

Yuan RL and Liu CJ. Experimental characterization of FRP mechanical connections. In: Proceedings of 3rd international conference on advanced composite materials in bridges and structures ACMBS-3, Ottawa, 2000, pp.103–110. The Canadian Society for Civil Engineers Montreal.

21.

Turvey GJ and Wang P. Single-bolt tension joints in pultruded GRP material effect of temperature on failure loads and strengths and joint efficiency. In: Proceedings of conference on strain measurement in the 21st century, 2001, pp.20–23. Lancaster, UK: British Society for Strain Measurement.

22.

Turvey GJ and Wang P. Effect of temperature on the structural integrity of bolted joints in pultrusions. In: Proceedings of international conference on composites in construction – CCC2001, 2001, pp.171–176. Lisse: A.A. Balkema Publishers, (Swets & Zeitlinger).

23.

Wang

. Bearing behavior of joints in pultruded composites. J Compos Mater 2002; 36: 2199–2216.

24.

Turvey GJ and Wang P. Single-bolt tension joints in pultruded GRP plate – effects of elevated temperature on failure loads, failure modes, load orientation and joint efficiency. In: Proceedings of joining plastics 2006, Rapra conference., paper no. 9, London, UK, 25–26 April 2006.

25.

Turvey

Wang

. Thermal preconditioning study for bolted tension joints in pultruded GRP plate. Compos Struct 2007; 77: 509–513.

26.

Turvey

Wang

. Failure of pultruded GRP single-bolt tension joints under hot–wet conditions. Compos Struct 2007; 77: 514–520.

27.

Turvey GJ and Wang P. Effect of hole clearance on bolt loads in pultruded GRP tension joints. In: Proceedings of 16th international conference on composite materials (ICCM-16), 8–13 July 2007, Kyoyto, Japan [paper Ref. FrHM1–03, pp.7 in CD-ROM of proceedings].

28.

Turvey

Wang

. Failure of pultruded GRP bolted joints: a Taguchi analysis. Eng Comput Mech 2009; 162: 155–166.

29.

Turvey GJ. Failure of single-lap single-bolt tension joints in pultruded glass fibre reinforced plate. In: Proceedings of 6th international conference on composites in construction engineering (CICE), Rome, 13–15 June 2012, paper number 08–089. http://www.iifc-hq.org/proceedings/CICE_2012/CICE.html (accessed 24 December 2015).

30.

Turvey GJ and Godé J. An experimental investigation of the tensile behaviour of single-lap bolted joints in pultruded GFRP plate. In: Proceedings of FRP bridge conference, London, 2012, pp.77–91. CD-ROM. Chesterfield: Net Composites.

31.

Zafari

Mottram

. Effect of hot-wet aging on the pin-bearing strength of a pultruded material with polyester matrix. J Compos Constr 2012; 16: 340–352.

32.

Turvey GJ. Ultimate loads, strength, extensions and strains of pultruded GFRP single-lap, single-bolt tension joints. In Proceedings of 6th international conference on advanced composites in construction, 2013, pp.373–382. Chesterfield: Net Composites Ltd.

33.

Lee

Y-G

Choi

Yoon

S-J

. Effect of geometric parameters on the mechanical behavior of PFRP single bolted connection. Comp Part B Eng 2015; 75: 1–10.

34.

Abd-El-Naby

SFM

Hollaway

. The experimental behaviour of bolted joints in pultruded glass/polyester material. Part 2: two-bolt joints. Composites 1993b; 24: 539–546.

35.

Prabhakaran R, Devara S and Razzaq Z. The effect of fiber orientation angle on the unnotched, open hole, and pin-loaded strength of a pultruded composite. In: 51st annual conference and expo for Composite Institute, Cincinnati, OH (United States), 5–7 February 1996. New York, NY: SPI Composites Institute.

36.

Prabhakaran

Razzaq

Devara

. Load and resistance factor design (LRFD) approach for bolted joints in pultruded composites. Compos Part B: Eng 1996; 27: 351–360.

37.

Hassan

Mohamedien

Rizkalla

. Multibolted joints for GFRP structural members. J Compos Constr, ASCE 1997; 1: 3–6.

38.

Prabhakaran R and Robertson J. An experimental investigation of load-sharing in a multi-bolt pultruded composite joint. In: Proceedings of 2nd international conference on composites in infrastructure (ICCI’98), Vol. II, University of Arizona, Tucson, 5–7 January 1998, pp.355–368.

39.

Turvey

Wang

. Environmental effects on the failure of GRP multi-bolt joints. Struct Build 2009; 162: 275–287.

40.

Girão Coelho

Mottram

Harries

. Bolted connections of pultruded GFRP: implications of geometric characteristics on net section failure. Compos Struct 2015; 131: 878–884.

41.

ASTM D3039/D3039M-00:2006. Standard test method for tensile properties of polymer–matrix composite materials. Vol. 15.03. ASTM International West Conshohocken, PA: Composite Materials.

42.

ASTM D3518/D3518M-94:2007. Standard test method for in-plane shear response of polymer matrix composite materials by tensile test of a ±45° laminate–matrix. Vol. 15.03. ASTM International. West Conshohocken, PA: Composite Materials.

43.

ASTM A370-12:2005. Standard test methods and definitions for mechanical testing of steel products. Vol. 01.03. West Conshohocken, PA: ASTM International.

44.

Kulak GL, Adams PF and Gilmor MI. Limit states design in structural steel. 5th ed. Canadian Institute of Steel Construction, Toronto, Ontario, 1995.