Micromechanical behavior of β-Al 3 Mg 2 -dispersed aluminum composite prepared by high-energy ball milling and hot pressing

Abstract

The present investigation deals with the ball milling of Al–Mg, which results in the formation of metastable fcc solid solutions after 100 h that transform into more stable β-Al₃Mg₂ phase during subsequent annealing treatment. Powder metallurgy route was successfully employed to synthesize different weight fractions of low density β-Al₃Mg₂ dispersed Al matrix composites. Maximum hardness was achieved for 15 wt% β-Al₃Mg₂-dispersed Al composites. Compacted composites display lower hardness for higher percentage (20 wt%) of dispersing phase due to possible agglomeration. Nanomechanical properties as obtained from nanoindentation and nanoscratch measurements substantiate the results obtained from the microhardness measurements. Moreover, the significant hardening of the Al matrix was successfully achieved by incorporation of low density β-Al₃Mg₂ phase.

Keywords

Mechanical alloying metal matrix composite powder metallurgy nanoindentation nanoscratch

Get full access to this article

View all access options for this article.

References

Scudino

Sakaliyska

Surreddi

. Mechanical alloying and milling of Al-Mg alloys. J Alloys Compd 2009; 483(1–2): 2–7.

Mukherjee

Ande

Manna

. Formation of nanostructured and amorphous β-Al₃Mg₂ based alloys by rapid solidification and mechanical milling. Mater Sci Eng A 2010; 527(20): 5078–5083.

Kelkar

Roth

Clark

. Automobile bodies: can aluminum be an economical alternative to steel. JOM 2001; 53(8): 28–32.

Miracle

. Metal matrix composites—from science to technological significance. Compos Sci Technol 2005; 65(15–16): 2526–2540.

Scudino

Liu

Sakaliyska

. Powder metallurgy of Al-based metal matrix composites reinforced with β-Al₃Mg₂ intermetallic particles: analysis and modeling of mechanical properties. Acta Mater 2009; 57(15): 4529–4538.

Suryanarayana

. Synthesis of nanocomposites by mechanical alloying. J Alloys Compd 2011; 509(Supplement 1): S229–S234.

Khadem

Nategh

Yoozbashizadeh

. Structural and morphological evaluation of Al-5vol.% SiC nanocomposite powder produced by mechanical milling. J Alloys Compd 2011; 509(5): 2221–2226.

Shokuhfar

Dashtbayazi

Alinejad

. Characterization of Al/SiC nanocomposite prepared by mechanical alloying method. Mater Sci Forum 2007; 553: 257–265.

Hosseini Monazzah

Pouraliakbar

Bagheri

. Toughness behavior in roll-bonded laminates based on AA6061/SiC_p composites. Mater Sci Eng A 2014; 598: 162–173.

10.

Pouraliakbar

Hosseini Monazzah

Bagheri

. Toughness prediction in functionally graded Al6061/SiCp composites produced by roll-bonding. Ceram Int 2014; 40(6): 8809–8825.

11.

Pouraliakbar

Nazari

Fataei

. Predicting charpy impact energy of Al6061/SiCp laminated nanocomposites in crack divider and crack arrester form. Ceram Int 2013; 39(6): 6099–6106.

12.

Khakbiz

Akhlaghi

. Synthesis and structural characterization of Al-B₄C nano-composite powders by mechanical alloying. J Alloys Compd 2009; 479(1–2): 334–341.

13.

Nemati

Khosroshahi

Emamy

. Investigation of microstructure, hardness and wear properties of Al-4.5 wt.% Cu-TiC nanocomposites produced by mechanical milling. Mater Des 2011; 32(7): 3718–3729.

14.

Poirier

Drew

RAL

Trudeau

. Fabrication and properties of mechanically milled alumina/aluminum nanocomposites. Mater Sci Eng A 2010; 527(29–30): 7605–7614.

15.

Scudino

Liu

Prashanth

. Mechanical properties of Al-based metal matrix composites reinforced with Zr-based glassy particles produced by powder metallurgy. Acta Mater 2009; 57(6): 2029–2039.

16.

Sameezadeh

Emamy

Farhangi

. Effects of particulate reinforcement and heat treatment on the hardness and wear properties of AA 2024-MoSi₂ nanocomposites. Mater Des 2011; 32(4): 2157–2164.

17.

Schoenitz

Dreizin

. Structure and properties of Al-Mg mechanical alloys. J Mater Res 2003; 18(8): 1827–1836.

18.

Aqeeli

NAl

Mendoza-Suarez

Labrie

. Phase evolution of Mg-Al- Zr nanophase alloys prepared by mechanical alloying. J Alloys Compd 2005; 400(1–2): 96–99.

19.

Singh

Suryanarayana

Mertus

. Extended homogeneity range of intermetallic phases in mechanically alloyed Mg-Al alloys. Intermetallics 2003; 11(4): 373–376.

20.

Zolriasatein

Khosroshahi

Emamy

. Mechanical and wear properties of Al-Al₃Mg₂ nanocomposites prepared by mechanical milling and hot pressing. Int J Min Met Mater 2013; 20(3): 290–297.

21.

Nemati

Emamy

Emami

. Hardness and wear properties of Al4.5%Cu/Al₃Mg₂ nanocomposite prepared by mechanical alloying. Mater Trans 2012; 53(7): 1310–1317.

22.

Khosroshahi

Zolriasatein

Emamy

. Synthesis and mechanical properties of a novel Al/Β-Al₃Mg₂ nanocomposite prepared by mechanical alloying process. Adv Mater Res 2012; 445: 827–832.

23.

Suryanarayana

. Mechanical alloying and milling. Prog Mater Sci 2001; 46(1–2): 1–184.

24.

Murty

Ranganathan

. Novel materials synthesis by mechanical alloying/milling. Int Mater Rev 1998; 43(3): 101–141.

25.

Sinha

Samanta

Manna

. Micromechanical characterization of bulk composite prepared by sintering of mechanically alloyed aluminum-316 stainless steel (35 wt.%) powder blend. Mater Sci Eng A 2011; 528(18): 6034–6038.

26.

Roy

Sinha

Chattopadhyay

. Nanoindentation behavior of bulk metastable Al65Cu20Ti15 alloy prepared by consolidation of the ball milled powder. Mater Sci Eng A 2011; 528(28): 8047–8050.

27.

Charleux

Gravier

Verdier

. Amorphous and partially crystallized metallic glasses: an indentation study. Mater Sci Eng A 2008; 483–484: 652–655.

28.

Drozdz

Kulik

Fecht

. Nanoindentation studies of Zr-based bulk metallic glasses. J Alloys Compd 2007; 441(1–2): 62–65.

29.

Mukhopadhyay

Belger

Paufler

. Nanoindentation studies on Cu–Ti–Zr–Ni–Si–Sn bulk metallic glasses. Mater Sci Eng A 2007; 449–451: 954–957.

30.

Yang

Riester

Nieh

. Strain hardening and recovery in a bulk metallic glass under nanoindentation. Scripta Mater 2006; 54(7): 1277–1280.

31.

Kim

Kang

Greer

. Evaluating plastic flow properties by characterizing indentation size effect using a sharp indenter. Acta Mater 2008; 56(14): 3338–3343.

32.

Williamson

Hall

. X-ray line broadening from filed aluminium and wolfram. Acta Metall 1953; 1(1): 22–31.

33.

Oliver

Pharr

. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J Mater Res 1992; 7(6): 1564–1583.

34.

Sinha

Chattopadhyay

. Nanomechanical response of martensite in Ti-(∼49 at.%) Ni alloy. Mater Sci Eng A 2012; 552: 540–546.

35.

Adams

Allan

Briscoe

. An experimental study of the nano-scratch behaviour of poly (methyl methacrylate). Wear 2001; 251(1): 1579–1583.

36.

Briscoe

Pelillo

Ragazzi

. Scratch deformation of methanol plasticized poly (methylmethacrylate) surfaces. Polymer 1998; 39(11): 2161–2168.

37.

Mukhopadhyay

Paufler

. Micro- and nanoindentation techniques for mechanical characterization of materials. Int Mater Rev 2006; 51(4): 209–245.

38.

Nix

Gao

. Indentation size effects in crystalline materials: a law for strain gradient plasticity. J Mech Phys Solid 1998; 46(3): 411–425.

39.

Hutchinson

. Plasticity at the micron scale. Int J Solids Struct 2000; 37(1–2): 225–238.

40.

Tymiak

Kramer

Bahr

. Plastic strain and strain gradients at very small indentation depths. Acta Mater 2001; 49(6): 1021–1034.

41.

Chaubey

Scudino

Mukhopadhyay

. Effect of particle dispersion on the mechanical behavior of Al-based metal matrix composites reinforced with nanocrystalline Al-Ca intermetallics. J Alloys Compd 2012; 536(1): S134–S137.

42.

Alcala

Barone

Anglada

. The influence of plastic hardening on surface deformation modes around Vickers and spherical indents. Acta Mater 2000; 48(13): 3451–3464.

43.

Z-H

Agren

. An analysis of piling-up or sinking-in behaviour of elastic-plastic materials under a sharp indentation. Philos Mag 2004; 84(23): 2367–2380.

44.

Gao

Huang

. Geometrically necessary dislocation and size-dependent plasticity. Scripta Mater 2003; 48(2): 113–118.

45.

Bolshakov

Pharr

. Influences of pileup on the measurement of mechanical properties by load and depth sensing indentation techniques. J Mater Res 1998; 13(4): 1049–1058.

46.

Elmustafa

. Pile-up/sink-in of rate-sensitive nanoindentation creeping solids. Modell Simul Mater Sci Eng 2007; 15(7): 823–834.