The presence of air bubbles impacts the quality of the produced composite part, by reducing its mechanical properties, and also it might degrade its surface finish. The modelling of air bubbles entrapment requires the consideration of three phenomena: air bubble’s creation, compression and transport. Very few studies have been conducted on this latter phenomenon. The model developed in this work is proposed for a unidirectional reinforcement. It is integrated into a simulation code of resin transfer moulding process, via the control volume finite element method. That model takes into account the dual scale pores in fibrous media, and simulates the three said phenomena highlighting the migration phenomenon and the coexistence of micro and macro air bubbles. As a result, the spatial distribution of created, compressed and transported air bubbles as well as its macro and micro remaining quantities, in the end of the injection are estimated.
PatelNLeeLJ. Effects of fiber mat architecture on void formation and removal in liquid composite molding. Polym Compos1995; 16: 104–114.
5.
PatelNLeeLJ. Model development and implementation. Polym Compos1996; 17: 104–114.
6.
Kang MK. A numerical and experimental study on the mold filling and void formation during resin transfer molding. PhD Thesis, Seoul National University, 1997.
7.
KangMKLeeWIHahnHT. Formation of microvoids during resin-transfer molding process. Compos Sci Technol2000; 60: 2427–2434.
8.
LabatLGriselMBreardJet al.Original use of electrical conductivity for void detection due to injection conditions of composite materials. CR Acad Sci – Ser IIB Mech2001; 329(serie II b): 529–534.
9.
LeeDHLeeWIKangMK. Analysis and minimization of void formation during resin transfer molding process. Compos Sci Technol2006; 66: 3281–3289.
10.
RuizEAchimVSoukaneSet al.Optimization of injection flow rate to minimize micro/macro-voids formation in resin transfer molded composites. Compos Sci Technol2006; 66: 475–486.
11.
FrishfeldsVLundstromSTJakovicsA. Bubble motion through non-crimp fabrics during composites manufacturing. Compos A2008; 39: 243–251.
12.
LundstromSTFrishfeldsVJakovicsA. Bubble formation and motion in non-crimp fabrics with perturbed bundle geometry. Compos A2010; 41: 83–92.
13.
ParkCHLebelASaouabAet al.Modeling and simulation of voids and saturation in liquid composite molding processes. Compos A2011; 42: 658–668.
14.
GueroultSLebelAParkCHet al.Analytical modeling and in situ measurement of void formation in liquid composite moulding processes. Adv Compos Mater2014; 23: 31–42.
15.
BowlesKJFrimpongS. Void effects on the interlaminar shear strength of unidirectional graphite-fiber-reinforced composites. J Compos Mater1992; 26: 1487–1509.
16.
AverousLGauvinR. Surface analysis of phenolic composites obtained by RTM process. J Reinf Plast Compos1998; 17: 1167–1184.
17.
HaiderMHubertPLessardL. An experimental investigation of class A surface finish of composites made by the resin transfer molding process. Compos Sci Technol2007; 67: 3176–3186.
18.
PalardyGHubertPHaiderMet al.Optimization of RTM processing parameters for Class A surface finish. Compos B2008; 39: 1280–1286.
19.
Eun SW and Lee WI. Experimental study of the microvoids formation and transport in the vacuum assisted resin transfer molding process. Master Thesis, Seoul National University, 2002.
20.
LeeDHLeeWIKangMK. Analysis and minimization of void formation during resin transfer molding process. Compos Sci Technol2006; 66: 3281–3289.
21.
ParkCHLeeWI. Modeling void formation and unsaturated flow in liquid composite molding processes: a survey and review. J Reinf Plast Compos2011; 11: 957–977.
22.
Ben AbdelwahedMAWielhorskiYBizetLet al.Characterisation of bubbles formed in a cylindrical T-shaped junction device. Chem Eng Sci2012; 76: 206–215.
23.
ChenYTDavisHTMacoskoCW. Wetting of fiber mats for composite manufacturing I: Visualization experiments. AIChE J1995; 41: 2261–2273.
24.
PatelNRohatgiVLeeJL. Micro scale flow behavior and void formation mechanism during impregnation through a unidirectional stitched fiberglass mat. Polym Compos1995; 35: 837–851.
25.
FairbrotherFStubbsAE. Studies in electro-endosmosis - VI. The "bubble tube" method of measurement. J Chem Soc1935; 18: 237–261.
26.
BrethertonFP. The motion of long bubbles in tubes. J Fluid Mech1961; 10: 166–188.
27.
AussillousPQuéréD. Quick deposition of a fluid on the wall of a tube. Phys Fluids2000; 12: 2367–2371.
28.
Gueroult S. Analyse expérimentale de la saturation des milieux fibreux à double échelle de pores : Application à la mise en œuvre des matériaux composites par le procédé RTM. PhD Thesis, Université du Havre, Le Havre, 2012.
