External compaction pressure over vacuum-bagged composite parts: Effect on the quality of flax fiber/epoxy laminates

Abstract

Vacuum bagging allows the removal of trapped air between fabrics layers, extraction of moisture and volatiles, and optimization of the fiber-to-resin ratio. However, during vacuum bagging the compaction pressure is limited to atmospheric pressure, preventing the composite reaching higher fiber volumetric contents and also allows surface porosity to arise, affecting the esthetical appearance of the composite and also its mechanical performance. While the autoclave process has shown to solve these problems, the cost of the equipment is too high for many applications. In the present work, a series of experiments are carried out by compressing unidirectional flax/epoxy vacuum-bagged laminates in a hydraulic press at different pressures. The quality of the laminates is analyzed in terms of surface finish, internal void content, and mechanical properties. The additional compaction from hydraulic pressure is shown to be very effective in improving considerably the overall quality of the composites.

Keywords

Polymer composites flax fiber mechanical properties porosity/voids vacuum bagging compression molding

Get full access to this article

View all access options for this article.

References

Shah

Schubel

Licence

et al.

Determining the minimum, critical and maximum fibre content for twisted yarn reinforced plant fibre composites. Compos Sci Technol 2012; 72: 1909–1917.

Siva

Winowlin Jappes

et al.

Effect of fiber volume fraction on the mechanical properties of coconut sheath/usp composite. J Manuf Eng 2013; 8: 60–63.

Varna

Joffe

Berglund

et al.

Effect of voids on failure mechanisms in RTM laminates. Compos Sci Technol 1995; 53: 241–249.

Costa

de Almeida

SFM

Cerqueira Rezende

. The influence of porosity on the interlaminar shear strength of carbon/epoxy and carbon/bismaleimide fabric laminates. Compos Sci Technol 2001; 61: 2101–2108.

. The voids formation mechanisms and their effects on the mechanical properties of flax fiber reinforced epoxy composites. Compos Part A Appl Sci 2015; 72: 40–48.

Kim

Shim

Sturtevant

et al.

Mechanical properties and production quality of hand-layup and vacuum infusion processed hybrid composite materials for GFRP marine structures. Int J Nav Archit Ocean Eng 2014; 6: 723–736.

Stringer

. Optimization of the wet lay-up/vacuum bag process for the fabrication of carbon fibre epoxy composites with high fibre fraction and low void content. Composites 1989; 20: 441–452.

Hamill

Centea

Nutt

. Surface porosity during vacuum bag-only prepreg processing: causes and mitigation strategies. Compos Part A Appl Sci 2015; 75: 1–10.

Eom

Boogh

Michaud

et al.

Stress-initiated void formation during cure of a three-dimensionally constrained thermoset resin. Polym Eng Sci 2001; 41: 492–503.

10.

Wisnom

Gigliotti

Ersoy

et al.

Mechanisms generating residual stresses and distortion during manufacture of polymer matrix composite structures. Compos Part A Appl Sci 2006; 37: 522–529.

11.

Boyard

Millischer

Sobotka

et al.

Behaviour of a moulded composite part: modelling of dilatometric curve (constant pressure) or pressure (constant volume) with temperature and conversion degree gradients. Compos Sci Technol 2007; 67: 943–954.

12.

Potter

. The early history of the resin transfer moulding process for aerospace applications. Compos Part A Appl Sci 1999; 30: 619–21.

13.

Lundström

. Measurement of void collapse during resin transfer moulding. Compos Part A Appl Sci 1997; 28: 201–14.

14.

Afendi

Banks

Kirkwood

. Bubble free resin for infusion process. Compos Part A Appl Sci 2005; 36: 739–46.

15.

Haider

Hubert

Lessard

. An experimental investigation of class a surface finish of composites made by the resin transfer molding process. Compos Sci Technol 2007; 67: 3176–3186.

16.

Kunhanandan Nambiar

Ramamurthy

. Air‐void characterisation of foam concrete. Cement Concrete Res 2007; 37: 221–230.

17.

Zhang

Wang

. The pore characteristics of geopolymer foam concrete and their impact on the compressive strength and modulus. Front Mater 2016; 3: 38–38.

18.

Summerscales

Guild

Pearce

NRL

et al.

Voronoi cells, fractal dimensions and fibre composites. J Microsc 2001; 201: 153–162.

19.

The MathWorks Inc. Matlab Version 8.6.0.267246 (R2015b), Natick, MA: The MathWorks Inc, 2015.

20.

Kane

Karthik

Butt

et al.

Microstructural characterization and pore structure analysis of nuclear graphite. J Nucl Mater 2011; 415: 189–197.

21.

ASTM D790-15e2. Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials, ASTM International, West Conshohocken, PA, 2015. www.astm.org. DOI: 10.1520/D0790-15E02.

22.

ASTM D3039 / D3039M-14. Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, ASTM International, West Conshohocken, PA, 2014, www.astm.org. DOI: 10.1520/D3039_D3039M-14.

23.

Kelly

Umer

Bickerton

. Viscoelastic response of dry and wet fibrous materials during infusion processes. Compos Part A Appl Sci 2006; 37: 868–873.

24.

Chen

Lang

Chou

. Experimental and theoretical studies of fabric compaction behavior in resin transfer molding. Mater Sci Eng A 2001; 317: 188–196.

25.

Chen

Chou

. Compaction of woven-fabric preforms in liquid composite molding processes: single-layer deformation. Compos Sci Technol 1999; 59: 1519–1526.

26.

Somashekar

Bickerton

Bhattacharyya

. An experimental investigation of non-elastic deformation of fibrous reinforcements in composites manufacturing. Compos Part A Appl Sci 2006; 37: 858–867.

27.

Robitaille

Gauvin

. Compaction of textile reinforcements for composites manufacturing. III: reorganization of the fiber network. Polym Compos 1999; 20: 48–61.

28.

Francucci

Rodriguez

Vazquez

. Experimental study of the compaction response of jute fabrics in liquid composite molding processes. J Compos Mater 2012; 46: 155–167.

29.

Anders

Centea

et al.

Eliminating volatile-induced surface porosity during resin transfer molding of a benzoxazine/epoxy blend. Compos Part A Appl Sci 2016; 84: 442–454.

30.

Charlet

Baley

Morvan

et al.

Characteristics of Hermès flax fibres as a function of their location in the stem and properties of the derived unidirectional composites. Compos Part A Appl Sci 2007; 38: 1912–1921.

31.

Gning

Liang

Guillaumat

et al.

Influence of process and test parameters on the mechanical properties of flax/epoxy composites using response surface methodology. Mater Sci 2011; 46: 6801–6801.

32.

Oksman

. High quality flax fibre composites manufactured by the resin transfer moulding process. J Reinf Plast Compos 2001; 20: 621–627.

33.

Heijenrath

Peijs

. Natural-fibre-mat-reinforced thermoplastic composites based on flax fibres and polypropylene. Adv Compos Lett 1996; 5: 81–85.