Introduction of intra-tow release/storage mechanisms in reactive dual-scale flow numerical simulations

Abstract

Classical dual-scale reactive simulations of the RTM process assume permanent intra-tow resin storage in the saturated domain. However, recent experimental investigations revealed that permanent storage is occurring only in a limited volume of the tows. In the remaining volume, fluid is released in the channels with a rate that depends on the architecture of the textile and on the fiber volume fraction. Based on experimental observations, a new model is proposed to refine the simulation of the high speed reactive RTM process: a simplified microstructural model is used to enable permanent and partial transient storage within the tows. Additionally, a new sink term is proposed to reproduce the kinetics of the convective tow-channel fluid exchanges in the saturated domain. After a state of the art on dual-scale and reactive flow, the experimental inputs of the study are presented. The new model is then introduced, validated and characterized using the experimental inputs. Additionally, the influence of the release mechanisms on a reactive dual-scale injection is estimated by conducting comparative single-scale, and dual-scale simulations with transient or permanent storage. The new model has been demonstrated to be appropriate to reproduce accurately the release mechanisms, and simulations reveal the interest of taking these release mechanisms into account to simulate reactive dual-scale injections with an increased accuracy.

Keywords

RTM dual-scale flow reactive flow sink term numerical simulation

Get full access to this article

View all access options for this article.

References

Parseval

Pillai

Advani

. A simple model for the variation of permeability due to partial saturation in dual scale porous media. Transport Porous Media 1997; 27: 243–264.

Tan

Roy

Pillai

. Variations in unsaturated flow with flow direction in resin transfer molding: an experimental investigation. Compos Part A 2007; 38: 1872–1892.

Lawrence

Neacsu

Advani

. Modeling the impact of capillary pressure and air entrapment on fiber tow saturation during resin infusion in Lcm. Compos Part A 2009; 40: 1053–1064.

Shih

Lee

. Effect of fiber architecture on permeability in liquid composite molding. Polym Compos 1998; 19: 626–639.

Roy T, Dulmes C and Pillai KM. Experimental investigations of the unsaturated flow in liquid composite molding. In: Proceedings of the 5th Canadian international composites conference, Vancouver, Canada, 16 August 2005.

Imbert M. High speed reactive RTM with on-line mixing in dual-scale fibrous reinforcements: experimental and numerical developments and investigations. PhD Thesis, École Centrale de Nantes, France, 2017.

Imbert

Abisset-Chavanne

Comas-Cardona

et al.

Efficient dual-scale flow and thermo-chemo-rheological coupling simulation during on-line mixing resin transfer molding process. J Compos Mater 2018; 52: 313–330. .

Imbert

Comas-Cardona

Abisset-Chavanne

et al.

Experimental investigation of intra-tow fluid storage mechanisms in dual-scale fiber reinforcements. Compos Part A 2017; 107: 70–82.

Williams

Landel

Ferry

et al.

The temperature dependence of relaxation mechanisms in amorphous polymers and other glass-forming liquids. J Am Chem Soc 1955; 77: 3701–3707.

10.

Kamal

Sourour

. Kinetics and thermal characterization of thermoset cure. Polym Eng Sci 1973; 13: 59–64.

11.

Kendall

Rudd

. Flow and cure phenomena in liquid composite molding. Polym Compos 1994; 15: 334–348.

12.

Lee

Young

Lin

. Mold filling and cure modeling of RTM and SRIM processes. Compos Struct 1994; 27: 109–120.

13.

Pillai

Jadhav

. A numerical study of nonisothermal reactive flow in a dual-scale porous medium under partial saturation. Numer Heat Transf 2004; 47: 109–136.

14.

Tan

Pillai

. Multiscale modeling of unsaturated flow of dual-scale fiber preform in liquid composite molding ii: non-isothermal flows. Compos Part A 2012; 43: 14–28.

15.

Abisset-Chavanne

Chinesta

. Toward an optimisation of the reactive resin transfer molding process: thermo-chemico-mechanical coupled simulations. Int J Mater Form 2014; 7: 249–258.

16.

García

Gascón

Chinesta

et al.

An efficient solver of the saturation equation in liquid composite molding processes. Int J Mater Form 2010; 3: 1295–1302.

17.

Tan

Pillai

. Multiscale modeling of unsaturated flow in dual-scale fiber preforms of liquid composite molding iii: reactive flows. Compos Part A 2012; 43: 29–44.

18.

Ivankovic

Incarnato

Kenny

et al.

Curing kinetics and chemorheology of epoxy/anhydride system. J Appl Polym Sci 2003; 90: 3012–3019.