The carbon fiber-reinforced composites were prepared in a vacuum oven using pre-preg composites, and the edge surfaces of the composite coupons were treated using high performing adhesives to eliminate the free-edge effects. The primary objective of the study was to usefully address the free-edge effects of composites used in aircraft and other manufacturing industries. The mechanical test results conducted on the untreated and edge-treated test coupons showed that the edge treatment and fiber orientations significantly affected the tensile strength and quality of the composites. It is determined that applying adhesives on the edges of the coupons could improve the mechanical properties of the composites, about 11%. Successful testing and evaluation of materials can lead to the precise analysis of a structure, and predictable behavior of the end design. This study may open up new possibilities to enhance the overall mechanical properties of fiber-reinforced composites for various manufacturing industries.
AsmatuluRBollavaramPKPatlollaVR, et al.Investigating the effects of metallic submicron and nanofilms on fiber-reinforced composites for lightning strike protection and EMI shielding. Adv Compos Hybrid Mater2020;
3: 1–18.
2.
SwarnaVSAlarifiIMKhanWA, et al.Enhancing fire and mechanical strengths of epoxy nanocomposites for metal/metal bonding of aircraft aluminum alloys. Polym Compos2019;
40: 3691–3702.
3.
Jones RM. Mechanics of composite materials. CRC Press, 2014.
4.
ASTM Committee D-30 on Composite Materials. Standard test method for tensile properties of polymer matrix composite materials.
West Conshohocken:
ASTM International, 2008.
5.
Kar KK (ed). Composite materials: processing, applications, characterizations.
New York:
Springer, 2016.
6.
ASTM International ASTM D6415. Standard test method for measuring the curved beam strength of a fiber-reinforced polymer-matrix composite. West Conshohocken: ASTM International, 2006.
7.
DandekarCRShinYC.Modeling of machining of composite materials: a review. Int J Mach Tools Manuf2012;
57: 102–121.
8.
ZitouneRCollombetFLachaudF, et al.Experiment–calculation comparison of the cutting conditions representative of the long fiber composite drilling phase. Compos Sci Technol2005;
65: 455–466.
9.
ArolaDRamuluMWangDH.Chip formation in orthogonal trimming of graphite/epoxy composite. Compos Part A Appl Sci Manuf1996;
27: 121–133.
10.
AgarwalHAmaranathAJamtheY, et al.An investigation of cutting mechanisms and strain fields during orthogonal cutting in CFRPs. Mach Sci Technol2015;
19: 416–439.
11.
DharanCKHWonMS.Machining parameters for an intelligent machining system for composite laminates. Int J Mach Tools Manuf2000;
40: 415–426.
12.
AlarifiIMAlharbiAKhanWS, et al.Mechanical and thermal properties of carbonized PAN nanofibers cohesively attached to surface of carbon fiber reinforced composites.Macromol Symp2016;
365: 140–150.
13.
ZhangDWangHBurksAR, et al.Delamination in rotary ultrasonic machining of CFRP composites: finite element analysis and experimental implementation. Int J Adv Manuf Technol2020;
107: 1–12.
14.
PaulDRamachandranVGuptaNK.Improvements in the crushing behaviour of glass fibre-epoxy composite tubes by the addition of hollow glass particles. Thin Walled Struct2019;
141: 111–118.
15.
Nguyen-DinhNBouvetCZitouneR.Influence of machining damage generated during trimming of CFRP composite on the compressive strength. J Compos Mater2020;
54: 1413–1430.
16.
WernCWRamuluMShuklaA.Investigation of stresses in he orthogonal cutting of fiber-reinforced plastics. Exp Mech1996;
36: 33–41.
17.
Nguyen-DinhNHejjajiAZitouneR, et al.New tool for reduction of harmful particulate dispersion and to improve machining quality when trimming carbon/epoxy composites. Compos Part A Appl Sci Manuf2020;
131: 105806.
18.
NayakDBhatnagarNMahajanP.Machining studies of uni-directional glass fiber reinforced plastic (UD-GFRP) composites part 1: effect of geometrical and process parameters.Mach Sci Technol2005;
9: 481–501.
19.
CadorinNZitouneR.Wear signature on hole defects as a function of cutting tool material for drilling 3D interlock composite. Wear2015;
332: 742–751.
20.
CadorinNZitouneRSeitierP, et al.Analysis of damage mechanism and tool wear while drilling of 3D woven composite materials using internal and external cutting fluid. J Compos Mater2015;
49: 2687–2703.
21.
BallardMKWhitcombJD.Effect of heterogeneity at the fiber–matrix scale on predicted free-edge stresses for a [0/90] s laminated composite subjected to uniaxial tension. J Compos Mater2019;
53: 625–639.
22.
FeyelFChabocheJL.FE2 multiscale approach for modelling the elastoviscoplastic behaviour of long fibre SiC/Ti composite materials. Comput Methods Appl Mech Eng2000;
183: 309–330.
23.
OwensBCWhitcombJDVargheseJ.Effect of finite thickness and free edges on stresses in plain weave composites. J Compos Mater2010;
44: 675–692.
24.
O'BrienT.Comparisons of various configuration of the edge delaminate test for interlaminar fracture toughness (NASA Technical Memorandum). Hampton: Langley Research Center, 1985.
25.
ChuGSunC.Reducing free edge effect on laminate strength by edge modification. J Compos Mater1991;
25: 142–161.
26.
WangASD.Free-edge delamination in layered composites – a historical review of the past 30 years.Mech Behav Adv Mater1998;
1998: 223–226.
27.
Cytec Industries, Inc. CEM launch out-of-autoclave toughened epoxy resin prepreg system for, www.cytec.com/innovation/CEMhighlights.htm (2009, accessed 9 October 2020).
28.
Saenz-CastilloDMartínMICalvoS, et al.Effect of processing parameters and void content on mechanical properties and NDI of thermoplastic composites. Compos Part A Appl Sci Manuf2019;
121: 308–320.
29.
BalakrishnanVSObrosovAKukeF, et al.Influence of metal surface preparation on the flexural strength and impact damage behaviour of thermoplastic FRP reinforced metal laminate made by press forming. Compos Part B Eng2019;
173: 106883.
30.
HintzeWHartmannDSchütteC.Occurrence and propagation of delamination during the machining of carbon fibre reinforced plastics (CFRPs) – an experimental study. Compos Sci Technol2011;
71: 1719–1726.
31.
TorabiARPirhadiE.On the ability of the notch fracture mechanics in predicting the last-ply-failure of blunt V-notched laminated composite specimens: a hard problem can be easily solved by conventional methods. Eng Fract Mech2019;
217: 106534.
32.
PatlollaVRKashaniMSJabbarniaA, et al. Effects of porosity on interlaminar tensile strength of curved specimen. In: SAMPE fall technical conference, Charleston, NC, 2012.
33.
BrauningKA.Mitigation of machining damage on delamination of fiber reinforced composite tensile coupons. MS Thesis, Wichita State University, USA, 2013.
34.
HejjajiAZitouneRToubalL, et al.Influence of controlled depth abrasive water jet milling on the fatigue behavior of carbon/epoxy composites. Compos Part A Appl Sci Manuf2019;
121: 397–410.
35.
HaddadMZitouneREymaF, et al.Influence of machining process and machining induced surface roughness on mechanical properties of continuous fiber composites. Exp Mech2015;
55: 519–528.
36.
GhidossiPEl MansoriMPierronF.Edge machining effects on the failure of polymer matrix composite coupons. Compos Part A Appl Sci Manuf2004;
35: 989–999.
37.
HaddadMZitouneRBougheraraH, et al.Study of trimming damages of CFRP structures in function of the machining processes and their impact on the mechanical behavior. Compos Part B Eng2014;
57: 136–143.
38.
GhidossiPEl MansoriMPierronF.Influence of specimen preparation by machining on the failure of polymer matrix off-axis tensile coupons. Compos Sci Technol2006;
66: 1857–1872.
NosierAMalekiM.Free-edge stresses in general composite laminates. Int J Mech Sci2008;
50: 1435–1447.
43.
PawadeRSJoshiSSBrahmankarPK.Effect of machining parameters and cutting edge geometry on surface integrity of high-speed turned Inconel 718. Int J Mach Tools Manuf2008;
48: 15–28.
44.
KaratasMAGokkayaHNalbantM.Optimization of machining parameters for abrasive water jet drilling of carbon fiber-reinforced polymer composite material using Taguchi method. AircrEng Aerosp Technol2019;
92: 128–138.
45.
KappelAMittelstedtC.Free-edge stress fields in cylindrically curved cross-ply laminated shells. Compos Part B Eng2020;
183: 107693.
46.
KharghaniNSoaresCG.Analytical and experimental study of the ultimate strength of delaminated composite laminates under compressive loading. Compos Struct2019;
228: 111355.
