On the Bearing Strength of Bolted Graphite/Epoxy Laminates

Abstract

One of the basic failure modes of bolted composite laminates is bearing fail ure. This mode of failure occurs in the material immediately adjacent to the contact points of bolt and laminate, and is caused primarily by compressive stresses acting on the hole boundary. The results of an experimental program which measured the bearing strengths of two different types of graphite/epoxy specimens are presented. The influence on the bearing strength of several important parameters including lateral constraint and ply orien tation are shown. Strains were measured in the vicinity of the loaded hole to quantify the extent of bearing failure. A new approach to predicting bearing failure is outlined. The Delamination Buckling Model (DBM) assumes that ply buckling following delaminations is a major feature of bearing failure. Quantitatively good agreement was found between ex periment and model results.

Get full access to this article

View all access options for this article.

References

Hart-Smith, L.J. 1986. "Design and Analysis of Bolted and Riveted Joints in Fibrous Composite Structures," International Symposium on Joining and Repair of Fibre-Reinforced Plastics, Imperial College, London.

Collings, T.A. 1982. "On the Bearing Strength of CFRP Laminates," Composites, 13:241-252.

Stockdale, J.H. and F.L. Matthews. 1976. "The Effect of Clamping Pressure on Bolt Bearing Loads in Glass Fibre Reinforced Plastics," Composites, 7:34-38.

Quinn, W.J. and F.L. Matthews. 1977. "The Effect of Stacking Sequence on the Pin-Bearing Strength in Glass Fibre Reinforced Plastics," Journal of Composite Materials, 11:139-142.

Collings, T.A. 1977. "The Strength of Bolted Joints in Multi-Directional CFRP Laminates," Aeronautical Research Council, Current Paper 1380.

Kim, R.Y. and J.M. Whitney. 1976. "Effect of Temperature and Moisture on the Pin-Bearing Strength of Composite Laminates," Journal of Composite Materials, 10:149-151.

Waszczak, J.P. and T.A. Cruse. 1971. "Failure Mode and Strength Prediction of Anisotropic Bolt Bearing Specimens," Journal of Composite Materials, 5:421-425.

Agarwal, B.L. 1980. "Static Strength Prediction of Bolted Joint in Composite Material," AIAA Journal, 18:1345-1375.

Soni, S.R. 1981. "Failure Analysis of Composite Laminates with a Fastener Hole," Joining of Composite Materials, ASTM STP 749, K. T. Kedward, ed., American Society for Testing and Materials, pp. 145-164.

10.

Chang, F.K. , R.A. Scott and G.S. Springer. 1984. "Failure of Composite Laminates Containing Pin-Loaded Holes-Method of Solution," Journal of Composite Materials, 18:255-278.

11.

Oplinger, D.W. and D.R. Gandhi. 1974. "Analytical Studies of Structural Performance in Mechanically Fastened Fiber-Reinforced Plates ," in Proceedings of Army Symposium on Solid Mechanics, 1974: The Role of Mechanics in Design-Structural Joints, Army Materials and Mechanics Research Center, AMMRC MS 74-8, pp. 211-242.

12.

Tsujimoto, Y. and D.W. Wilson. 1986. "Elasto-Plastic Failure Analysis of Composite Bolted Joints," Journal of Composite Materials, 20:236-251.

13.

Timoshenko, S. 1936. Theory of Elastic Stability , New York: McGraw-Hill.

14.

Lekhnitskii, S.G. 1968. Anisotropic Plates, trans. S. W. Tsai and T. Cheron. New York: Gordon and Beach Science.

15.

Jones, R.M. 1975. Mechanics of Composite Materials, Washington, DC: Scripta.

16.

Drinkard, R. Drew , Jr. and Nacy K. Sulinski. 1981. MACSYMA: A Program for Computer Algebraic Manupilation, Naval Underwater Systems Center, Newport, RI.

17.

Eriksson, L.I. 1986. "Contact Stresses in Bolted Joints of Composite Laminates," Composite Structures, 6:57-75.