The Adiabatic Thermoelastic Effect in Laminated Fiber Composites

Abstract

The influence of material inhomogeneity and anisotropy on the reversible, adiabatic thermoelastic effect in laminated, continuous-fiber composites is investigated analytically and experimentally. The plane-stress solution for strains in a uniform laminate is combined with a simple micromechanics description of a fiber-reinforced lamina to approximate the nonhomogeneous strains in the fibers and matrix. The equations of anisotropic, linear thermoelasticity are then used to evaluate the temperature change in each of the microconstituents during an adiabatic deformation. The average temperature change of the surface plies of several carbon/epoxy laminates are computed and compared with experimental data obtained via differential infrared thermography. Results indicate that material parameters such as the volume fraction and thermoelastic properties of the microconstituent materials, the orientations of the laminae within the laminate, and the orientation of the lamina on the surface of observation affect the measurable thermoelastic response of a particular laminate. The experimental results suggested that the deformations of the polymeric composite test specimens were not perfectly adiabatic, yet the major trends in the measured thermoelastic emission patterns were nonetheless represented reasonably well by the proposed analysis. Based on the results, suggestions for further refinements to the analysis are proposed.

Keywords

thermoelasticity differential thermography micromechanics composite laminates SPATE

Get full access to this article

View all access options for this article.

References

1. Bakis, C. E. , and K. L. Reifsnider . 1988. “Nondestructive Evaluation of Fiber Composite Laminates by Thermoelastic Emission,” Review of Progress in Quantitative Nondestructive Evaluation, 7:1109–1116.

2. Lohr, D. T. , and B. I. Sandor . 1987. “Impact Damage Analysis by Differential Infrared Thermography,” Proc. SEM Fall Conference, Savannah, GA, pp. 39–44.

3. Lohr, D. T. , N. F. Enke and B. I. Sandor . 1987. “Analysis of Fatigue Damage Evolution by Differential Infrared Thermography,” Proc. SEM Fall Conference, Savannah, GA, pp. 169–174.

4. Cox, B. N. , and D. E. Pettit . “Nondestructive Evaluation of Composite Materials Using the Stress Pattern Analysis by Thermal Emissions Technique,” Proc. SEM Spring Conf., Houston, TX, June 14–19, 1987.

5. Biot, M. A. 1956, “Thermoelasticity and Irreversible Thermodynamics,” J. Appl. Phys., 27: 240–253.

6. Potter, R. T.

“Stress Analysis in Laminated Fiber Composites by Thermoelastic Emission.”

Proc. 2nd Int. Conf. Stress Anal, by Thermoelastic Tech., London, Feb. 17–18, 1987.

7. Thomson, W. 1853. “On the Dynamical Theory of Heat,” Trans. R. Soc. Edinb., 20:261–288.

8. Joule, J. P. 1859. “On Some Thermo-Dynamic Properties of Solids,” Philos. Trans. R. Soc., 149: 91–131.

9. Compton, K. T. , and D. B. Webster . 1915. “Temperature Changes Accompanying the Adiabatic Compression of Steel,” Phys. Rev., 5(Series 2):159–168.

10.

10. Dillon, O. W. , and T. R. Tauchert . 1966. “The Experimental Technique for Observing the Temperature Due to the Coupled Thermoelastic Effect,” Int. J. Solids Str., 2:385–390.

11.

11. Belgen, M. H. 1967. “Structural Stress Measurements with an Infrared Radiometer,” ISA Trans., 6:49–53.

12.

12. Stanley, P. and W. K. Chan . 1985. “Quantitative Stress Analysis by Means of the Thermoelastic Effect,” J. Strain Anal., 20:129–137.

13.

13. Gilmour, I. W. , A. Trainor and R. N. Haward . 1978. “The Thermoelastic Effect in Glassy Polymers,” J. Polym. Sci.: Polym. Phys. Ed., 16:1277–1290.

14.

14. Haward, R. N. , and A. Trainor . 1974. “The Thermoelastic Effect in PMMA,” J. Mater. Sci., 9:1243–1254.

15.

15. Jordan, E. H. , and B. I. Sandor . 1978. “Stress Analysis from Temperature Data,” J. Testing and Eval., JTEVA, 6:325–331.

16.

16. Stanley, P. and W. K. Chan . 1986. “SPATE Stress Studies of Plates and Rings under In-Plane Loading.” Exper. Mech., 26:360–370.

17.

17. Higuchi, M. and Y. Imai . 1970. “Rheological Interpretation of Heat Generation Associated with Fatigue of Polycarbonate,” J. Appl. Polym. Sci., 14:2377–2383.

18.

18. Nowacki, W. 1975. Dynamic Problems of Thermoelasticity. Noordhoff.

19.

19. Thomson, W. 1857. “On the Thermo-Elastic and Thermo-Magnetic Properties of Matter,” Q. J. Math., 1:57–77.

20.

20. Jones, R. M. 1975. Mechanics of Composite Materials. Washington, DC: Scripta.

21.

21. Timoshenko, S. P. , and J. N. Goodier . 1970. Theory of Elasticity, 3rd Ed. New York: McGraw-Hill.

22.

22. Oliver, D. E. 1987. “Stress Pattern Analysis by Thermal Emission,” Chapter 14 in SEM Handbook on Experimental Mechanics, A. S. Kobayashi , ed., Prentice-Hall.

23.

23. Bakis, C. E. and K. L. Reifsnider. 1989. “Adiabatic Thermoelastic Measurements,” Section VII-B in SEM Manual on Experimental Methods for Mechanical Testing of Composites, R. L. Pendleton and M. E. Tuttle, eds., Soc. Exp. Mech., pp. 139–146.

24.

24. Chamis, C. C. 1984. “Simplified Composite Micromechanics Equations for Hygral, Thermal, and Mechanical Properties,” SAMPE Q., 15:14–23.

25.

25. Kriz, R. D. , and W. W. Stinchcomb . 1982. “Effects of Moisture, Residual Thermal Curing Stresses, and Mechanical Load on the Damage Development in Quasi-Isotropic Laminates,” in Damage in Composite Materials, STP 775, K. L. Reifsnider , ed., Philadelphia: ASTM, pp. 63–80.