Effect of Radial Clearance between Bolt and Washer on the Bearing Strength of Composite Bolted Joints

Abstract

When composite materials are bolted together, the relative diameters of the bolt hole, the constraining washer and the bolt itself have a profound effect on the ulti mate bearing strength. Previous studies have investigated the effects of clearance between the bolt and the hole diameter. In this study, the effect of the difference between the bolt diameter and the inside diameter of the washer, which provides the lateral constraint at the edge of the hole, is examined. To explain the significant variation of bearing strength with bolt-to-washer clearance, a model is proposed to explain the mechanics of load transfer and the lateral deformation at the edge of the hole. The test results, using a quasi-isotropic graphite epoxy laminate, support the proposed model and provide data for designers.

Get full access to this article

View all access options for this article.

References

Crews, J.H. 1981. "Bolt-Bearing Fatigue of a Graphite Epoxy Laminate," Joining of Composite Materials, ASTM STP 749, K T. Kedward, ed., American Society for Testing and Materials, pp. 131-144.

Stockdale, J.H. and F.L. Matthews. 1976. "The Effect of Clamping Pressure on Bolt Bearing Loads in Glass Fibre Reinforced Plastics," Composites, 7(1).34-38.

Jurf, R.A. 1986. "Behavior of Bolted Joints in Composite Laminates," Ph.D. dissertation, University of Delaware.

Eriksson, I. 1990. "On the Bearing Strength of Bolted Graphite/Epoxy Laminates," Journal of Composite Materials, 24:1246-1269.

Collings, T.A. 1982. "On the Beanng Strengths of CFRP Laminates," Composites, 13(3) :241-252.

Collings, T.A. 1977. "The Strength of Bolted Joints in Multi-Directional CFRP Laminates," Composites, 8(1):43-55

Quinn, W.J. and F.L. Matthews. 1977. "The Effect of Stacking Sequence on the Pin-Bearing Strength in Glass Fibre Reinforced Plastic," J. of Composite Materials, 11:139-145.

Roberts, J.C. 1985. "Evaluation of a Double Lap Composite Clamped Joint," J. of Composite Materials , 19:376-389.

Sung, N.H. and N.P. Suh. 1979. "Effect of Fiber Orientation on Friction and Wear of Fiber Reinforced Polymeric Composites," Wear, 53:129-141.

10.

Hyer, M.W. , E.C. Klang and D.E. Cooper. 1987. "The Effects of Pin Elasticity, Clearance, and Friction on the Stresses in a Pin-Loaded Orthotropic Plate," J. of Composite Materials, 21·190-206

11.

Smith, P.A. , M.F. Ashby and K.J. Pascoe 1987. "Modelling Clamp-Up Effects in Composite Bolted Joints," J. of Composite Materials, 21.878-897

12.

Bickley, W.G. 1928 "The Distribution of Stress Round a Circular Hole in a Plate," Phil. Trans. Royal Soc. London, Series A227 383-415

13.

Shigley, J.E. and C.R. Mischke 1989. Mechanical Engineering Design McGraw-Hill.

14.

Crews, J.H. 1990 "An Apparatus for Bearing-Bypass Testing of Bolted Joints," Experimental Techniques , 14(6):54-57

15.

Bickford, J.H. 1981. An Introduction to the Design and Behavior of Bolted Joints Marcel Dekker, Inc.

16.

Kulak, G.L. , J.W. Fisher and J.H. Struik. 1987. Guide to Design Criteria for Bolted and Riveted Joints, Second Editions New York: Wiley.