On the Bearing Strength of Fibre Metal Laminates

Abstract

Published work on mechanically fastened joints in composites has demon strated that the influence of lateral restraint on bearing strength is of paramount impor tance. Delamination in conjunction with buckling is frequently observed if there is a lack of lateral restraint (pin-type loading). An investigation is performed on the bearing strength behaviour of fibre metal laminates (ARALL and GLARE) for which similar fail ure modes are found. The theoretical analysis is based on an existing delamination buck ling model for composites. However, an alternative out-of-plane deformation function in corporating a variation with respect to the angle is used. The energy method is extended to include the strain energy of both the aluminium and the prepreg layers. The analytical procedure is supported by finite element calculations, and the theoretical predictions are compared with available experimental data. Very good correlation is obtained. If there is sufficient lateral restraint (bolt-type loading) the bearing ultimate strength can, on the other hand, be predicted by a simple rule of mixtures based on the aluminium volume fraction.

Keywords

fibre metal laminates bearing strength delamination buckling effect of lateral restraint.

Get full access to this article

View all access options for this article.

References

Vogelesang, L.B. and G.H.J.J. Roebroeks . 1990. Fatigue of Fibre Metal Laminates , 4th International Spring Meeting, Fatigue of Metal Matrix Composites and Multimaterials, Paris, June 12-13, 1990.

Stockdale, J.H. and F.L. Matthews. 1976. "The Effect of Clamping Pressure on Bolt Bearing Loads in Glass Fibre Reinforced Plastics," Composites, 7:34-38.

Collings, T.A. 1977. "The Strength of Bolted Joints in Multi-Directional CFRP Laminates," Composites, 8:43-55.

Eriksson, I. 1990. "On the Bearing Strength of Bolted Graphite/Epoxy Laminates," Journal of Composite Materials, 24:1246-1269.

"Standard Method for Pin Type Bearing Test of Metallic Materials," Annual Book of ASTM Standards, Item E238-68.

"Standard Method of Test for Bearing Strength of Plastics," Annual Book of ASTM Standards, Item D953-54.

Marshall, I.H. , W. S. Arnold, J. Wood and R.F. Mousley. 1989. "Observations on Bolted Connections in Composite Structures," Composite Structures , 13:133-151.

van Wimersma Greidanus, B. 1990. "Design and Testing of a Circumferential and Longitudinal Joint of the A320 Fuselage Section 13/14 in GLARE," Report LR-645. Faculty of Aerospace Engineering, Delft University of Technology.

Ericson, K. , M. Persson, L. Carlsson and A. Gustavsson . 1984. "On the Prediction of the Initiation of Delamination in a [0/90], Laminate with a Circular Hole," Journal of Composite Materials, 18:495-505.

10.

Lucking, W.M. , S.V. Hoo and T.S. Sankar. 1984. "The Effect of Geometry on Interlaminar Stresses of [0/90], Composite Laminates with Circular Holes," Journal of Composite Materials, 17:188-198.

11.

Timoshenko, S. and S. Woinowsky-Krieger . 1959. Theory of Plates and Shells . New York: McGraw-Hill Book Company .

12.

Hibbitt, Karlsson and Sorenson. 1989. "ABAQUS, A Finite Element System," User's Manual, Version 4.8.

13.

Tsai, S.W. and H.T. Hahn. 1980. Introduction to Composite Materials . Lancaster, PA: Technomic Publishing Co., Inc.