Direct torque controlled space vector modulated method for line start permanent magnet synchronous and induction motors

Abstract

This paper presents a thorough comparison of Direct Torque Controlled Space Vector Modulated (DTC-SVM) method for a three-phase four-pole Induction Motor and its equal Line-Start Permanent Magnet Synchronous Motor (LSPMSM), which is amended from an actual induction motor. For this reason, both nominal voltage and voltage sag conditions are tested for line-fed and voltage source inverter-fed of both motors, and a comparison between induction motor and LSPMSM behavior shows that synchronization problems of LSPMSM during line-fed conditions are obviated by DTC-SVM method. In addition, a superior transient and steady-state performance of the LSPMSM drive is observed rather than an induction motor, especially for voltage sag conditions.

Keywords

Control systems design electrical machines induction machine motion control motor drives

Get full access to this article

View all access options for this article.

References

Arab Markadeh

Daryabeigi

Lucas

. (2011) Speed and flux control of induction motors using emotional intelligent controller. Industry Application IEEE Transaction 47: 1126–1135.

Chee-Mun

(1997) Dynamic Simulation of Electric Machinery. New Jersey: Prentice Hall PTR.

deAlmeida

Ferreira

FjTE

Fong

JAC

(2011) Standards for efficiency of electric motors. Industry Applications Magazine, IEEE 17: 12–19.

Debruyne

Derammelaere

Desmet

. (2012) Comparative study of the influence of harmonic voltage distortion on the efficiency of induction machines versus line start permanent magnet machines. In: Harmonics and Quality of Power (ICHQP), IEEE 15th International Conference, Hong Kong, China, pp. 342–349.

Fei

Luk

. (2009) A high-performance line-start permanent magnet synchronous motor amended from a small industrial three-phase induction motor. Magnetics IEEE Transaction 45: 4724–4727.

Ferreira

FJTE

Baoming

deAlmeida

(2012) Stator winding connection mode management in line-start permanent magnet motors to improve their efficiency and power factor. In: International Conference Electrical Machines (ICEM) on IEEE. Palais des Congres et des Expositions de Marseille, Marseille, France, 2012.

Hardan

Zhang

Shepherd

(1996) Application of an extended Kalman filter for high-performance current regulation of a vector-controlled induction machine drive. Transactions of the Institute of Measurement and Control 18: 69–76.

Isfahani

Vaez-Zadeh

(2009) Line-start permanent magnet synchronous motors: Challenges and opportunities. Energy 34: 1755–1763.

Jidin

Idris

NRBN

Yatim

AHBM

. (2012) A wide speed high torque capability utilizing over-modulation strategy in DTC of induction machines with constant switching frequency controller. Power Electronic IEEE Transaction 27: 2566–2575.

10.

Kahrisangi

Isfahani

Vaez-Zadeh

. (2012) Line-start permanent magnet synchronous motors versus induction motors: A comparative study. Frontiers of Electrical and Electronic Engineering 7: 459–466.

11.

Kurihara

Rahman

(2004) High-efficiency line-start interior permanent-magnet synchronous motors. Industry Application IEEE Transaction 40: 789–796.

12.

Marcic

Stumberger

(2012) Comparison of induction motor and line-start ipm synchronous motor performance in a variable-speed drive. Industry Application IEEE Transaction 48: 2341–2352.

13.

Melfi

Evon

McElveen

(2009) Induction versus permanent magnet motors. Industry Application Magazine IEEE 15: 28–35.

14.

Shihua

Kai

Huixian

(2011) A composite speed controller based on a second-order model of permanent magnet synchronous motor system. Transactions of the Institute of Measurement and Control 33: 522–541.

15.

Stumberger

Marcic

Hadziselimovic

(2012) Direct comparison of induction motor and line-start IPM synchronous motor characteristics for semi-hermetic compressor drives. Industry Application IEEE Transaction 48: 2310–2321.

16.

Uddin

Hafeez

(2012) FLC-based DTC Scheme to improve the dynamic performance of an IM drive. Industry Application IEEE Transaction 48: 823–831.

17.

Vas

(1998) Sensorless Vector and Direct Torque Control. Oxford: Oxford University Press.

18.

Xiaodong

Huangqiu

Zebin

(2013) Application of LSSVM inverse in a variable frequency induction motor drive system. Transactions of the Institute of Measurement and Control 35: 247–254.

19.

Yon

(2009) A study on the optimal rotor design of LSPM considering the starting torque and efficiency. Magnetics IEEE Transaction 45: 1808–1811.

20.

Yongchang

Jianguo

(2011) Direct torque control of permanent magnet synchronous motor with reduced torque ripple and commutation frequency. Power Electronic IEEE Transaction 26: 235–248.

21.

Yongchang

Jianguo

Zhengming

. (2012) An improved direct torque control for three-level inverter-fed induction motor sensorless drive. Power Electronic IEEE Transaction 27: 1502–1513.

22.

Zhongkai

Yixiong

Jianrong

. (2008) A methodology to support product platform optimization using multi-objective evolutionary algorithms. Transactions of the Institute of Measurement and Control 30: 295–312.