Crystallinity of PLA is an important factor that affects its processability, mechanical strength, biodegradability, and service temperature. In this paper crystallization of PLA in solid state foaming process was studied in two main aspects: gas sorption in saturation stage, and heating as well as stretching in foaming stage. During CO2 saturation the equilibrium crystallinity jumped from 9.7% at 2 MPa to 26.4% at 3 MPa CO2 pressure. Further increases in saturation pressure did not increase the crystallinity. In the gas sorption stage of the process, it was found that the crystallization reached equilibrium at approximately the same time as the gas sorption reached equilibrium. Within the range of 2 to 5 MPa saturation pressures and 60 to 100°C foaming temperatures, a maximum crystallinity of 26.8% was observed in the foamed PLA. Crystallinity increased with the extent of cell-wall stretching during the foaming process.
GarlottaD., A literature review of poly(lactic acid). Journal of Polymers and the Environment, 9(2) (2001) 63–84.
5.
SommerJ.U., and ReiterG., Polymer crystallization, observations, concepts, and interpretations. Lecture notes in physics, 2003, Berlin, New York, Springer. xvii, 386.
6.
GeddeU.W., Polymer physics. 1st ed. 1995, London, New York, Chapman & Hall.
7.
KolstadJ.J., Crystallization kinetics of poly(L-lactide-co-meso-lactide). Journal of Applied Polymer Science, 62(7) (1996) 1079–1091.
8.
UrbanoviciE., SchneiderH.A., and CantowH.J., Some considerations concerning the temperature dependence of the bulk crystallization rate constants of polymeric materials. Journal of Polymer Science, Part B (Polymer Physics), 35(2) (1997) 359–69.
9.
TsujiH., and IkadaY., Properties and morphologies of poly(L-lactide), 1. Annealing condition effects on properties and morphologies of poly(L-lactide). Polymer, 36(14) (1995) 2709–16.
10.
RayS.S., and OkamotoM., Biodegradable Polylactide and Its Nanocomposites, Opening a New Dimension for Plastics and Composites. Macromolecular Rapid Communications, 24(14) (2003) 815–840.
11.
HuangJ., Crystallization and microstructure of poly(L-lactide-co-meso-lactide) copolymers. Macromolecules, 31(8) (1998) 2593–2599.
12.
WangX., KumarV., and LiW., Low density sub-critical CO2-blown solid-state PLA foams. Cellular Polymers, 26(1) (2007) 11–35.
13.
HuX.Polylactic acid (PLA)-CO2 foams at sub-critical conditions. In: ANTEC 2005. Boston, MA, United States, Society of Plastics Engineers, Brookfield, CT 06804-0403, United States.
14.
TakadaM., HasegawaS., and OhshimaM., Crystallization kinetics of poly(L-lactide) in contact with pressurized CO2. Polymer Engineering and Science, 44(1) (2004) 186–196.
15.
KokturkG., Evolution of phase behavior and orientation in uniaxially deformed polylactic acid films. Polymer Engineering and Science, 42(8) (2002) 1619–28.
16.
OuX., and CakmakM.X-ray studies of structural development during sequential and simultaneous biaxial stretching of polylactic acid film.2003. Nashville, TN, United States, Society of Plastics Engineers.
17.
OuX., and CakmakM., Influence of biaxial stretching mode on the crystalline texture in polylactic acid films. Polymer, 49(24) (2008) 5344–5352.
18.
MartiniJ., WaldmanF.A., and SuhN.P., The Production and Analysis of Microcellular Foam, in ANTEC1982. 674–676.
19.
KumarV., PhD Dissertation, Process Synthesis for Making Microcellular Thermoplastic Parts, A Case Study in Axiomatic Design, in Department of Mechanical Engineering. 1988, MIT, Boston.
20.
KumarV., and SuhN.P., A Process for Making Microcellular Thermoplastic Parts. Polymer Engineering and Science, 30(20) (1990) 1323–1329.
21.
KumarV., and WellerJ., Production of microcellular polycarbonate using carbon dioxide for bubble nucleation. Journal of Engineering for Industry, Transactions of the ASME, 116(4) (1994) 413–420.
22.
HollM.R., A steady-state mass balance model of the polycarbonate-CO2 system reveals a self-regulating cell growth mechanism in the solid-state microcellular process. Journal of Polymer Science, Part B, Polymer Physics, 39(8) (2001) 868–880.
23.
MooneyD.J., Novel approach to fabricate porous sponges of poly(D,L-lactic-co- glycolic acid) without the use of organic solvents. Biomaterials, 17(14) (1996) 1417–1422.
24.
WangX., LiW., and KumarV., A method for solvent-free fabrication of porous polymer using solid-state foaming and ultrasound for tissue engineering applications. Biomaterials, 27(9) (2006) 1924–1929.
25.
WangX., LiW., and KumarV.Solvent free fabrication of biodegradable porous polymers.2004. Anaheim, CA, United States, American Society of Mechanical Engineers, New York, NY 10016-5990, United States.
26.
LiaoX., NawabyA.V., and WhitfieldP.S., Carbon dioxide induced crystallization in poly (L lactic acid) and its effect on foam morphologies. Polymer International, 59(12) (2010) 1709–1718.
27.
BaldwinD.F., ShimboM., and SuhN.P., The role of gas dissolution and induced crystallization during microcellular polymer processing, a study of poly (ethylene terephthalate) and carbon dioxide systems. Journal of Engineering Materials and Technology, 117(1) (1995) 62–74.
28.
DoroudianiS., ParkC.B., and KortschotM.T., Effect of the crystallinity and morphology on the microcellular foam structure of semicrystalline polymers. Polymer Engineering & Science, 36(21) (1996) 2645–2662.
29.
MichaelsA.S., and BixlerH.J., Flow of gases through polyethylene. Journal of Polymer Science, 1961. 50(154), 413–439.
30.
MichaelsA.S., and BixlerH.J., Solubility of gases in polyethylene. Journal of Polymer Science, 50(154) (1961) 393–412.
31.
FischerE., SterzelH.J., and WegnerG., Investigation of the structure of solution grown crystals of lactide copolymers by means of chemical reactions. Colloid & Polymer Science, 251(11) (1973) 980–990.
32.
StaufferD., and AharonyA., Introduction to Percolation Theory. 2nd ed. 1992, London, Washington, DC, Taylor & Francis.
