Secondary hardening by precipitation of alloy carbides during tempering in an experimental Cr-Mo-V alloy steel was studied under continuous and isothermal conditions. Measurements of microhardness and nanohardness analysed the hardening behaviour during stage IV as a function of time, temperature, and heating rate. Scanning electron microscopy and scanning probe evidenced the carbides precipitated during stage IV. It was observed that hardening is a function of not only tempering temperature and time but also of the heating rate according to the Hollomon–Jaffe parameter. The parameter increases as the heating rate increases due to the effect on the temperature, showing a clear softening. The hardening behaviour, evaluated with the Hollomon–Jaffe parameter, was very similar regardless of the test, micro- or nanoindentation.
LiuQQianDHuaL. Transformation from non-isothermal to isothermal tempering of steel based on isoconversional method. J Mater Sci2018; 53: 2774–2784.
2.
Hesamodin TalebiSGhasemi-NanesaHJahaziM, et al.In situ study of phase transformations during non-isothermal tempering of bainitic and martensitic microstructures. Metals2017; 7: 346.
3.
KaiserDDe GraaffBJungAM, et al.A dilatometric study on the influence of compressive stresses on the tempering of martensitic AISI 4140 steel - evidence of transfor-mation induced plasticity during cementite precipitation. Mater Sci Eng A2017; 705: 114–121.
4.
ZhaoYRenXHuZ, et al.Effect of tempering on microstructure and mechanical properties of 3Mn-Si-Ni martensitic steel. Mater Sci Eng A2018; 711: 397–404.
5.
EuserVKWilliamsonDLClarkeAJ, et al.Limiting retained austenite decomposition in quenched and tempered steels: influences of rapid tempering and silicon. ISIJ Int2020; 60: 2990–3000.
6.
JuYGoodallAStrangwoodM, et al.Characterisation of precipitation and carbide coarsening in low carbon low alloy Q&T steels during the early stages of tempering. Mater Sci Eng A2018; 738: 174–189.
7.
Balan KPVenagopal ReddyA.Aero steels: Part 1-low alloy steels. In: Eswara Prasad N and Wanhill RJH (eds) Aerospace Materials and Material Technologies. 1st ed. India: Springer Singapore, 2017, pp.149–171.
8.
NingDDaiCRWuJL, et al.Carbide precipitation and coarsening kinetics in low carbon and low alloy steel during quenching and subsequently tempering. Mater Charact2021; 176: 111111.
9.
RevillaCLópezBRodriguez-IbabeJM. Carbide size refinement by controlling the heating rate during induction tempering in a low alloy steel. Mater Des2014; 62: 296–304.
10.
NykielTHryniewiczT. Transformations of carbides during tempering of D3 tool steel. J Mater Eng Perform2014; 23: 2050–2054.
11.
JiaCLiuYLiuC, et al.Precipitates evolution during tempering of 9CrMoCoB (CB2) ferritic heat-resistant steel. Mater Charact2019; 152: 12–20.
12.
ZhouTBabuRPHouZ, et al.Precipitation of multiple carbides in martensitic CrMoV steels - experimental analysis and exploration of alloying strategy through thermodynamic calculations. Materialia 2020; 9: 100630.
13.
PhamTHNguyenNV. Mechanical properties of constituent phases in structural steels and heat-affected zones investigated by statistical nanoindentation analysis. Constr Build Mater2021; 268: 121211.
14.
OhmuraTHaraTTsuzakiK. Evaluation of temper softening behavior of Fe-C binary martensitic steels by nanoindentation. Scr Mater2003; 49: 1157–1162.
15.
ChengGZhangFRuimiA, et al.Quantifying the effects of tempering on individual phase properties of DP980 steel with nanoindentation. Mater Sci Eng A2016; 667: 240–249.
16.
LiHGaoSTianY, et al.Influence of tempering on mechanical properties of ferrite and martensite dual phase steel. Mater Today Proc2015; 2: S667–S671.
17.
BroitmanE. Indentation hardness measurements at macro-, micro-, and nanoscale: a critical overview. Tribol Lett2017; 65. DOI: https://doi.org/10.1007/s11249-016-0805-5
18.
López-MartínezEVázquez-GómezOVergara-HernándezJ, et al.Mechanical characterization of the welding of two experimental HSLA steels by microhardness and nanoindentation tests. Met Mater Int2016; 22: 987–994.
19.
DaiTLippoldJC. Tempering behavior of the fusion boundary region of an F22/625 weld overlay. Weld Res2017; 96: 467–480.
20.
HollomonJHJaffeLD. Ferrous metallurgical design: design principles for fully hardened steel. New York: John Wiley & Sons, 1947.
21.
VirtanenEVan TyneCJLevyBS, et al.The tempering parameter for evaluating softening of hot and warm forging die steels. J Mater Process Technol2013; 213: 1364–1369.
22.
LeivaJAVMoralesEVVillar-CociñaE, et al.Kinetic parameters during the tempering of low-alloy steel through the non-isothermal dilatometry. J Mater Sci2010; 45: 418–428.
23.
ChengLBrakmanCMKorevaarBM, et al.The tempering of iron-carbon martensite; dilatometric and calorimetric analysis. Metall Trans A1988; 19: 2415–2426.
24.
XuLQZhangDTLiuYC, et al.Precipitation behavior and martensite lath coarsening during tempering of T/P92 ferritic heat-resistant steel. Int J Miner Metall Mater2014; 21: 438–447.
25.
KafadarGKalkanliAÖzdemirAT, et al.Effect of isothermal transformation treatment and tempering on the microstructure and hardness of a medium C and high Si steels. ISIJ Int2021; 61: 1679–1687.
26.
Baltazar HernándezVHNayakSSZhouY. Tempering of martensite in dual-phase steels and its effects on softening behavior. Metall Mater Trans A2011; 42: 3115–3129.
27.
DépinoySToffolon-MascletCUrvoyS, et al.Carbide precipitation in 2.25 Cr-1 Mo bainitic steel: effect of heating and isothermal tempering conditions. Metall Mater Trans A2017; 48: 2164–2178.
28.
PorterDAEasterlingKESherifMY. Phase transformations in metals and alloys. Boca Raton: CRC Press, 2009.
