Determination of 6D Workspaces of Gough-Type Parallel Manipulator and Comparison between Different Geometries

Abstract

We consider in this paper a Gough-type parallel robot whose leg length values are constrained to lie within some fixed ranges and for which there may be mechanical limits for the motion of the passive joints.

The purpose of this paper is to present algorithms to determine:

• the constant orientation workspace: all the possible locations of the center of the platform that can be reached with a fixed orientation

• thetotal orientation workspace: all the possible locations of the center of the platform that can be reached with any orientation in a set defined by three ranges for the orientation angles (the dextrous workspace is an example of total orientation workspace case, the three ranges being T [0,360] degree1)

• the inclusive orientationworkspace: all the possible locations of the center of the platform that can be reached with at least one orientation among a set defined by three ranges for the orientation angles (the maximal or reachableworkspace is an example of inclusive orientation workspace, the three ranges being [0,360])

Most of these algorithms are based on a basic method: approximation of the result by a set of 3D or 6D boxes obtained from an initial estimation through a bisection process. The boxes in the result will either fully or partially lie inside the workspace: the bisection stops as soon as all the boxes that do not lie fully inside the workspace have a size that is lower than a fixed threshold.

A companion algorithm enables to verification that any 6D workspace (i.e., a continuous set of poses) lies within the reachable workspace of the robot. The paper includes a comparison between the workspace volumes of four different robot geometries, which shows that for robots of similar dimensions the joints layout has a large influence on the workspace volume.

Get full access to this article

View all access options for this article.

References

Gosselin, C. 1990. Determination of the workspace of 6-d of parallel manipulators . ASME J. of Mechanical Design 112(3): 331–336 .

Gosselin, C., Lavoie, E., and Toutant, P. 1992. An efficient algorithm for the graphical representation of the threedimensional workspace of parallel manipulators . Paper presented at 22nd Biennial Mechanisms Conf., September 13-16, Scottsdale, AZ.

Haugh, E. J., Adkins, F. A., and Luh, C. M. 1995. Domain of operation and interference for bodies in mechanisms and manipulators. In Computational Kinematics, ed. J-P. Merlet and B. Ravani, 193–202. Dordrecht, the Netherlands: Kluwer .

Haugh, E. J., Adkins, F. A., and Luh, C. M. 1998. Operational envelopes for working bodies of mechanisms and manipulators . ASME J. of Mechanical Design 120(1): 84–91 .

Husty, M. L. 1996. On the workspace of planar three-legged platforms . Paper presented at World Automation Congress, vol. 3, 339–344, May 28-30, Montpellier, France.

Jo, D. Y., and Haug, E. J. 1989. Workspace analysis of closed loop mechanisms with unilateral constraints . Paper presented at ASME Design Automation Conf. September 17-20, Montréal.

Kim, D. I., Ching, W. K., and Youm, Y. 1997. Geometrical approach for the workspace of 6-dof parallel manipulators . Paper presented at IEEE Int. Conf. on Robotics and Automation, April 21-28, Albuquerque, NM.

Kumar, V. 1992. Characterization of workspaces of parallel manipulators . ASME J. of Mechanical Design 114: 368–375 .

Kurtz, R. L., and Hayward, V. 1992. Multiple-goal kinematic optimization of a parallel spherical mechanism with actuator redundancy . IEEE Trans. on Robotics and Automation 8(5): 644–651 .

10.

Luh, C. M., Adkins, F. A., Haugh, E. J., and Qiu, C. C. 1996. Working capability analysis of Stewart platforms . J. of Mechanical Design 118(2): 221–227 .

11.

Masory, O., Wang, J., and Zhuang, H. 1993. On the accuracy of a Stewart platform-part II: Kinematic calibration and compensation . Paper presented at IEEE Int. Conf. on Robotics and Automation, May 2-6, Atlanta, GA.

12.

Merlet, J-P. 1997a. Estimation efficace des caractéristiques de robots paralèlles: Extremums des raideurs et des coordonnées, vitesses, forces articulaires et singularités dans un espace de travail en translation. Research Report 3243, September, INRIA.

13.

Merlet, J-P. 1997b. Les Robots parallèles. Paris: Hermès.

14.

Merlet, J-P., Gosselin, C., and Mouly, N. 1998. Workspaces of planar parallel manipulators . Mechanism and Machine Theory 33(1/2): 7–20 .

15.

Moore, R. E. 1979. Methods and Applications of Interval Analysis. Philadelphia, PA: SIAM Studies in Applied Mathematics .

16.

Pooran, F. J. 1989. Dynamics and control of robot manipulators with closed-kinematic chain mechanism. Ph.D. thesis, The Catholic University of America, Washington DC.

17.

Stoughton, R., and Arai, T. 1993. A modified Stewart platform manipulator with improved dexterity . IEEE Trans. on Robotics and Automation 9(2): 166–173 .