This paper presents predictions and validations of shape distortions of a curved C-spar, using a simulation tool developed in the general purpose FE-program ABAQUS. The simulation tool is based on a simplified mechanical constitutive model that accounts for the mechanisms identified in a previous experimental study concerning the influence from the cure schedule on shape distortions. The main objective of the present paper is to validate the simplified constitutive model and a simplified simulation approach. The feasibility for simulation of shape distortions of a component with relatively complex shape has also been investigated.
Aronhime, M. T. and Gillham, J. K. (1986). Time-Temperature-Transformation (TTT) Cure Diagram of Thermosetting Polymeric Systems, In: Dusek, K. (Ed.), Epoxy Resins and Composites III, pp. 83-113, Springer-Verlag, Berlin .
2.
Radford, D. W. and Rennick, T. S. (2000). Separating Source of Manufacturing Distortion in Laminated Composites , Journal of Reinforced Plastics and Composites, 19(8): 621-641 .
3.
Bogetti, T. A. and Gillespie, J. W. (1992). Process-Induced Stress and Deformation in Thick-Section Thermoset Composite Laminate , Journal of Composite Materials, 26(5): 626-660 .
4.
White, S. R. and Hahn, H. T. (1992). Process Modeling of Composite Materials: Residual Stress Development during Cure, Part I Model Formulation , Journal of Composite Materials, 26(16): 2402-2422 .
5.
White, S. R. and Hahn, H. T. (1992). Process Modeling of Composite Materials: Residual Stress Development during Cure, Part II Experimental Validation , Journal of Composite Materials, 26(16): 2423-2453 .
6.
White, S. R. and Kim, Y. K. (1998). Process-Induced Residual Stress Analysis of AS4/3501-6 Composite Material , Mechanics of Composite Material and Structures, 5: 153-186 .
7.
Prasatya, P. , McKenna, G. B. and Simon, S. L. (2001). A Viscoelastic Model for Predicting Isotropic Residual Stresses in Thermosetting Materials: Effects of Processing Parameters , Journal of Composite Materials, 35: 826-849 .
8.
Johnston, A. , Vaziri, R. and Poursartip, A. (2001). Journal of Composite Materials, 35: 1435-1469 .
9.
Fernlund, G. , Rahman, N. , Courdji, R. , Bresslauer, M. , Poursartip, A. , Willden, K. and Nelson, K. (2002). Experimental and Numerical Study of the Effect of Cure Cycle, Tool Surface, Geometry, and Lay-up on the Dimensional Fidelity of Autoclave-processed Composite Parts , Composites Part A: Applied Science and Manufacturing, 33: 341-351 .
and F. Adb El Hady, Department of Automotive Engineering, Ain Shams University, Cairo, Egypt (Eds).
12.
Huang, X. , Gillespie, J. W. and Bogetti, T. (2000). Process Induced Stress for Woven Fabric Thick Section Composite Structures , Composite Structures, 49: 303-312 .
13.
Svanberg, J. M. and Holmberg, J. A. (2002). Predictions of Shape Distortion, Part I FE-implementation of a Path Dependent Constitutive Model, Paper B, In: Svanberg, J. M. (2002). Predictions of Manufacturing Induced Shape Distortions, Doctoral Thesis, Lulea University of Technology, Department of Materials and Manufacturing Engineering, Division of Polymer Engineering, Report 2002: 40.
14.
Svanberg, J. M. and Holmberg, J. A. (2001). An Experimental Investigation on Mechanisms for Manufacturing Induced Shape Distortion in Homogenous Balanced Laminates , Composites Part A: Applied Science and Manufacturing, 32(6): 827-838 .
15.
Svanberg, J. M. and Holmberg, J. A. (2002). Predictions of Shape Distortion, Part II Experimental Validation and Analysis of Boundary Conditions, Paper C, In: Svanberg, J. M. (2002). Predictions of Manufacturing Induced Shape Distortions, Doctoral Thesis, Lulea University of Technology, Department of Materials and Manufacturing Engineering, Division of Polymer Engineering, Report 2002: 40.
16.
Svanberg, J. M. (2002). Shape Distortion of a Non-isothermally Cured Composite Angle Bracket , Plastics Rubbers and Composites, 31(9): 398-404 .
17.
Product Data Sheet: RTM 6 (1998). HEXCEL Composites,
18.
Holmberg, J. A. (1998). Influence of Chemical Shrinkage on Shape Distortion of RTM Composites , In: Proceedings of 19th International SAMPE European Conference of the Society for the Advancement of Material and Process Engineering, pp. 621-632 , Paris, France, 22-24 April.
19.
Christensen, R. M. (1982). Theory of Viscoelasticity, 2nd edn., Academic Press, New York .
20.
Nielsen, L. E. (1969). Cross-Linking-Effects on Physical Properties of Polymers , J. Macromol. Sci. Revs. Macromol. Chem., C3(1): 69-103 .
21.
Simon, S. L. , McKenna, G. B. and Sindt, O. (2000). Modeling the Evolution of the Dynamic Mechanical Properties of a Commercial Epoxy During Cure after Gelation , Journal of Applied Polymer Science, 76(4): 495-508 .
22.
Zocher, M. A. , Grooves, S. E. and Allen, D. H. (1997). A Three-Dimensional Finite Element Formulation for Thermoviscoelastic Media , International Journal for Numerical Methods in Engineering, 40: 2267-2288 .
23.
Plepys, A. R. and Farris, R. J. (1990). Evolution of Residual Stresses in Three-dimensionally Constrained Epoxy Resin , Polymer, 31: 1932-1936 .
24.
Holmberg, J. A. (1997). Resin Transfer Moulded Composite Materials, Doctoral Thesis, Lulea University of Technology, Department of Materials and Manufacturing Engineering, Division of Polymer Engineering, Report 1997: 10.
25.
Whitney, J. M. and McCullough, R. L. (1990). Micromechanical Material Modelling, Delaware Composites Design Encyclopedia, Vol. 2, pp. 65-72, Technomic Pub. Co. Inc., Lancaster, Pennsylvania, USA .
26.
Gudmundsson, P. and Zang, W. (1993). An Analytic Model for Thermoelastic Properties of Composite Laminates Containing Transverse Matrix Cracks , International Journal of Solids and Structures, 30: 3211-3231 .
27.
Hull, D. (1988). An introduction to Composite Materials, University Press, Cambridge .
