An Experimental Study of the Water-Assisted Injection Molding of PA-6 Composites

Abstract

This report was carried out to study experimentally the water-assisted injection molding process of glass fiber-reinforced polyamide-6 (Nylon-6) composites. Experiments were carried out on an 80 ton injection molding machine equipped with a lab scale water injection system, which included a water pump, a water injection pin, a pressure accumulator, a water tank equipped with a temperature regulator, and a control circuit. The materials used were Nylon and 30% glass fiber-filled Nylon composites. A spiral mold cavity was used to mold the composites. After molding, the lengths of water penetration in molded parts were measured. The effects of different processing parameters on the lengths of water penetration were determined: melt temperature, mold temperature, melt-filling speed, short-shot size, water pressure, water temperature, water hold, and water injection delay time. Mechanical property tests were performed on the water-assisted injection molded parts. X-ray diffraction was also employed to identify the structural parameters of the materials. In addition, the in-mold temperature distribution of the polymeric materials during the cooling process was measured. Irregular water penetration in molded parts was observed, and water temperature was found to affect the crystallinity distribution of molded parts. Nevertheless, its effects on the tensile properties of molded materials were relatively limited.

Keywords

water-assisted injection molding glass fiber-reinforced Nylon-6 composites processing parameters mechanical property structural parameters temperature distribution.

Get full access to this article

View all access options for this article.

References

Knights, M. (2002). Water Injection Molding Makes Hollow Parts Faster, Lighter, Plast. Technol., April, 42-48.

Michaeli, W. , Juntgen, T. and Brunswick, A. (2001). WIT - En Route to Series Production: First Industrial Application of the Water Injection Technique , Kunststoff Plast Europe, 91: 37-39.

Liu, S.J. and Chen, Y.S. (2004). The Manufacturing of Thermoplastic Composite Parts by Water-Assisted Injection-Molding Technology, Comp. Part A: Appl. Sci. Manufacture, 35: 171-180.

Wu, Y.C. , Chen, K.M. and Liu, S.J. (2006). Core Out Geometries in Water Channels of Water Assisted Injection Moulded Parts, Plast. Rubber Comp., 35: 425-431.

Turng, L.S. (1995). Development and Application of CAE Technology for the Gas-Assisted Injection Molding Process, Adv. Polym. Tech., 14: 1-13.

Johnson, L. , Olley, P. and Coates, P.D. (2000). Gas Assisted Injection Moulding. Finite Element Modelling and Experimental Validation, Plast. Rubber Comp. , 29: 31-37.

Potente, H. , Moritzer, E. and Oberman, C.H. (1996). Foam Formation in Gas-Assisted Injection Molded Parts: Theoretical and Experimental Considerations, Polym. Eng. Sci., 36: 2163-2171.

Product Catalog, Mapex, Ginar Chem. Co., Taiwan.

Chandra, A. , Gong, S. , Yuan, M. , Turng, L.S. , Grumman, P. and Cordes, H. (2005). Microstructure and Crystallography in Microcellular Injection-Molded Polyamide-6 Nanocomposite and Neat Resin, Polym. Eng. Sci., 45: 52-61.

10.

Xenopoulos, A. and Clark, E.S. (1995). Nylon Plastic Handbook, Hanser , New York.

11.

Aharoni, S.A. (1997). n-Nylons: Their Synthesis, Structure, and Properties , John Wiley & Sons, New York .

12.

Sanjeeva Murthy, N. , Kagan, V.A. and Bray, R.G. (2002). Effect of Melt Temperature and Skin-Core Morphology on the Mechanical Performance of Nylon 6, Polym. Eng. Sci., 42: 940-950.

13.

Liu, S.J. and Chen, W.K. (2004). Experimental Investigation and Numerical Simulation of the Cooling Process in Water Assisted Injection Molded Parts, Plast. Rubber Comp., 33: 260-266.