Effect of MAPE on Mechanical and Morphological Properties of Wheat Straw/HDPE Injection Molded Composites

Abstract

The effect of MAPE as compatibilizer on mechanical and morphological properties of a wheat straw/high density polyethylene composite was investigated. Tensile strength, tensile modulus, tensile energy absorption, failure strain, and notched Izod toughness were much higher for composites with compatibilizer as compared with the composites with no compatibilizer. The use of 2% compatibilizer improved the tensile strength as high as 43%, tensile modulus to 116% and impact strength (notched) by 12%. Remarkably improvements were attained even with 1% compatibilizer. There was little difference in the properties obtained between the 1% and 2% compatibilizer. SEM micrographs of tensile fracture surfaces with 2% compatibilizer indicated a continuous failure and the particles are not released from the matrix which is the case in samples without compatibilizer.

Keywords

high density polyethylene compatibilizer wheat straw composite SEM mechanical properties MAPE.

Get full access to this article

View all access options for this article.

References

Bledzki, A.K. , Sperber, V.E. and Faruk, O. (2002). Natural and Wood Fiber Reinforcement in Polymer, Rapra Review. Rep., 13: 152.

Bigg, D.M. , Hiscock, D.F. , Peterson, J.R. and Bradbury, E.J. ( 1998). High Performance of Thermoplastic Matrix Composites , Journal of Thermoplastic Composite Materials, 1: 146-160.

Rowell, R.M. , Sandi, A.R. , Caulfield, D.F. and Jacobson, R.E. ( 1997). The Utilization of Natural Fibers in Plastic Composites: Problem and Opportunities, In: Leao, A. L. , Carvalho, F. X. and Frollini, E. (eds.), Lignocellulosic Plastic Composites, USP and a UNESP, Braz il.

Hull, D. ( 1981). An Introduction to Composite Materials, Cambridge University Press, Cambridge .

Raj, R.G. and Kokta, B.V. ( 1991). Improving the Mechanical Properties of HDPE Wood Fiber Composite with Additives/Coupling Agents, In: Proceedings of the 49th Annual Technical Conference, Montreal , Canada, Society of Plastic Engineers, pp. 1883-1885.

Maldas, D. and Kokta, B.V. ( 1989). Improving Adhesion of Wood Fiber with Polystyrene by Chemical Treatment of Wood Fiber with a Coupling Agent and the Influence on the Mechanical Properties of Composites, Journal of Adhesion Science Technology, 3: 529-539.

Sanadi, R.A. , Caulfield, D.F. and Jacobson, R.E. ( 1997). Agro-Fiber-Thermoplastic Composites, CRC Press, New York.

Klyosov, A.A. ( 2007). Wood-Plastic Composites, John Wiley and Sons, New York.

Rana, A.K. , Mandal, B.C. , Jacobson, M.R. , Rowell, R.M. and Banerjee, A.N. ( 1998). Short Jute fiber-Reinforced Polypropylene Composite: Effect of Compatibilizer, Journal of Applied Polymer Science , 69: 329-338.

10.

Rowell, R.M. , Caulfield, D.F. , Chen, G.W. , Ellis, D. , Jacobson, R.E. , Lange, S.E. and Schumann, R. ( 1998). Recent Advances in Agro-fiber/Thermo Plastic Composites , In: Proceedings of the 2nd International Symposium on Natural Polymers and Composites, Atibaia, SP, Brazil, pp. 11-98.

11.

Clemens, C. ( 1995). Exploratory Microscopic Investigation of Impacted Paper Fiber Reinforced Polypropylene Composite, In: Proceedings of Wood Fiber-Plastic Composites, Madison, Wisconsin, No. 7293, pp. 173-179.

12.

Adhikary, K.B. , Peng, S. and Staiger, M.P. (2007). Dimensional Stability and Mechanical Behavior of Wood-plastic Composites Based on Recycled and Virgin High Density Polyethylene, Journal of Composite, Part B: Engineering , pp. 1-9.

13.

Karmenker, A.C. and Youngquest , J.A. (1996). Injection Molding of Polypropylene Reinforced with Short Jute Fibers, Journal of Applied Polymer Science, 62: 1147-1151.

14.

Hedenberg, P. and Gatenholm, P. (1995). Conversion of Plastic/Cellulose Waste into Composites. I. Model of the Interphase, Journal of Applied Polymer Science, 56: 641-651.

15.

ASTM D638-90 (1991). Annual Book of ASTM Standards, Vol. 8.01 American Society of Testing and Materials, Philadelphia, PA .

16.

ASTM D256-90 (1991). Annual Book of ASTM Standards, Vol. 8.01 American Society of Testing and Materials, Philadelphia, PA .