Formability and flow front observation of carbon/polyamide 6 randomly oriented strand composites during compression molding

Abstract

Chopped carbon fiber tape-reinforced thermoplastics are randomly oriented strand materials that are easy to process and have good mechanical properties. Studying the formability and flow evolution during compression molding is essential; in particular, clarifying the relationship between the forming parameters and mold-filling characteristics of highly concentrated fiber suspensions. Here, we investigated the key parameters of strand size and effective pressure and demonstrated filling a complex mold cavity under practical processing conditions. In addition, a simplified method for observing the progression of the flow front using a video camera was proposed, where the dependence of the applied load on the mold-filling time could be observed. Filling complex-shaped mold cavity using chopped carbon fiber tape-reinforced thermoplastics is achievable using shorter strands and higher pressures. Also, the degradation of mechanical performance should be carefully considered when the material undergoes large deformation to form complex-shaped products.

Keywords

Carbon fibers discontinuous fiber composites randomly oriented strands compression molding observable mold

Get full access to this article

View all access options for this article.

References

Campbell

. Structural composite materials, 1st ed. Ohio: ASM International, 2010, pp. 1–18.

O'Brádaigh

Sheet forming of composite materials. In: Advani

(ed). Flow and rheology in polymer composites manufacturing, 1st ed. Amsterdam: Elsevier Science, 1994, pp. 517–569.

Pipes

Coffin

Simacek

et al.

Rheological behavior of collimated fiber thermoplastic composite materials. In: Advani

(ed). Flow and Rheology in Polymer Composites Manufacturing, 1st ed. Amsterdam: Elsevier Science, 1994, pp. 86–125.

Wan

Takahashi

. Tensile and compressive properties of chopped carbon fiber tapes reinforced thermoplastics with different fiber lengths and molding pressures. Comp Part A: Appl Sci Manuf 2016; 87: 271–281.

Yamashita

Hashimoto

Suganuma

et al.

Experimental characterization of the tensile failure mode of ultra-thin chopped carbon fiber tape-reinforced thermoplastics. J Reinf Plast Comp 2016; 35: 1342–1352.

Wan

Takahashi

. Tensile properties and aspect ratio simulation of transversely isotropic discontinuous carbon fiber reinforced thermoplastics. Comp Sci Technol 2016; 137: 167–176.

Ionita

Weitsman

. Randomly reinforced composites: properties, failure and aspects of material design. Probabilistic Eng Mech 2006; 21: 64–72.

Pan

Pelegri

. Progressive damage analysis of random chopped fiber composite using finite elements. J Eng Mater Technol 2011; 133: 011018–011018–7.

Selezneva

Lessard

. Characterization of mechanical properties of randomly oriented strand thermoplastic composites. J Comp Mater 2016; 50: 2833–2851.

10.

Selezneva

Roy

Meldrum

et al.

Modelling of mechanical properties of randomly oriented strand thermoplastic composites. J Comp Mater 2017; 51: 831–845.

11.

Stadtfeld

Erninger

Bickerton

et al.

An experimental method to continuously measure permeability of fiber preforms as a function of fiber volume fraction. J Reinf Plast Comp 2002; 21: 879–899.

12.

Chang

Hourng

. Analysis of flow phenomena during the filling stage of CTM. J Reinf Plast Comp 2004; 23: 1561–1570.

13.

Brookbank

Savage

Evans

. Economical carbon and cellulosic sheet moulding compounds for semi-and non-structural applications. J Reinf Plast Comp 2015; 34: 437–453.

14.

Landry

Hubert

. Experimental study of defect formation during processing of randomly-oriented strand carbon/PEEK composites. Comp Part A: Appl Sci Manuf 2015; 77: 301–309.

15.

Picher-Martel

Levy

Hubert

. Compression molding of carbon/polyether ether ketone composites: squeeze flow behavior of unidirectional and randomly oriented strands. Polym Comp 2015. DOI: 10.1002/pc.23753.

16.

Picher-Martel

Levy

Hubert

. Compression moulding of carbon/PEEK randomly-oriented strands composites: a 2D finite element model to predict the squeeze flow behaviour. Comp Part A: Appl Sci Manuf 2016; 81: 69–77.

17.

Lin

Ranganathan

Advani

Consolidation of continous fiber systems. In: Advani

(ed). Flow and rheology in polymer composites manufacturing, 1st ed. Amsterdam: Elsevier Science, 1994, pp. 326–358.

18.

Tadmor

Gogos

. Principles of polymer processing, 2nd ed. New Jersey: John Wiley & Sons, 2006, pp. 887–913.

19.

Advani

Sozer

. Process modeling in composites manufacturing, 2nd ed. Boca Raton, FL: CRC press, 2010, pp. 129–335.

20.

Schuster

Heider

Sharp

et al.

Thermal conductivities of three-dimensionally woven fabric composites. Comp Sci Technol 2008; 68: 2085–2091.

21.

Shin

Kim

Kawabe

et al.

Experimental studies of thin-ply laminated composites. Comp Sci Technol 2007; 67: 996–1008.

22.

ASTM D3039/D3039M:2002. Tensile properties of polymer matrix composite materials.

23.

Picher-Martel GP, Levy A and Hubert P. Squeeze flow of randomly oriented-oriented strands thermoplastic composites. In: Proceeding of 19th international conference on composite materials, Montréal, Canada, 28 July–2 August 2013, eProceedings part1, pp. 1872–1864.

24.

Törnqvist

Sunderland

Månson

JAE

. Non-isothermal process rheology of thermoplastic composites for compression flow mouldin. Comp Part A: Appl Sci Manuf 2000; 31: 917–927.

25.

Olivier

Cottu

Ferret

. Effects of cure cycle pressure and voids on some mechanical properties of carbon/epoxy laminates. Comp 1995; 26: 509–515.