Tribological properties of carbon nanotube as co-reinforcing additive in carbon black/acrylonitrile butadiene rubber composites for hydraulic seal applications

Abstract

This work investigated the cure characteristic, physical mechanical properties, and tribology behavior of carbon black filled acrylonitrile butadiene rubber composites using multi-walled carbon nanotubes as co-reinforcing additive in various contents from 0, 3, 6, 9, and 15 parts per hundred rubbers. The physical and tribological behavior was also observed in large-scale piston driven hydraulic apparatus which was specially designed for seal applications. The results suggested that the modulus and hardness were found to increase after adding multi-walled carbon nanotube whereas the tensile and tear strength were not significantly affected. Adding multi-walled carbon nanotube was found to increase the bound rubber and crosslink density. For ball-on-disc tribo-testing, it was found that the coefficient of friction of the rubber composites decreased with multi-walled carbon nanotube content and the applied loads whereas the specific wear rate was more influenced by the applied loads used. Finally, under the large-scale piston driven hydraulic test apparatus in comparison with commercial grade rubber seals, it was found that the weight loss for the acrylonitrile butadiene rubber composites with multi-walled carbon nanotube was much lower than that without multi-walled carbon nanotube. The carbon black/acrylonitrile butadiene rubber composites with 9–12 parts per hundred rubbers multi-walled carbon nanotube were recommended as the most suitable for hydraulic seal applications.

Keywords

Multi-walled carbon nanotubes composites tribology nitrile rubber reinforcement

Get full access to this article

View all access options for this article.

References

Shen

M-X

Peng

X-D

Meng

X-K

et al . Fretting wear behavior of acrylonitrile–butadiene rubber (NBR) for mechanical seal applications. Tribol Int 2016; 93: 419–428.

Bhaumik

Kumaraswamy

Guruprasad

et al . Investigation of friction in rectangular Nitrile-Butadiene Rubber (NBR) hydraulic rod seals for defence applications. J Mech Sci Technol 2015; 29: 4793–4799.

Chandrasekaran

Rubber seals for fluid and hydraulic systems. Elsevier Science, Oxford: William Andrew, 2009, pp.1–22.

Raadnui

Seal wear debris characterization for predictive maintenance. Wear 2015; 330–331: 490–497.

Dong

Yuan

Bai

et al . Tribological properties of aged nitrile butadiene rubber under dry sliding conditions. Wear 2015; 322–323: 226–237.

Ismail

Ramly

Othman

The effect of carbon black/multiwall carbon nanotube hybrid fillers on the properties of natural rubber nanocomposites. Polym Plast Technol Eng 2011; 50: 660–666.

Yang

et al . Friction properties of carbon nanotubes reinforced nitrile composites under water lubricated condition. Adv Mater Res 2011; 284-286: 611–614. [Trans Tech Publ].

Wang

Zhang

Tian

Mechanical and tribological properties of acrylonitrile–butadiene rubber filled with graphite and carbon black. Mater Des 2012; 39: 450–457.

Gao

Gong

et al . The role of carbon nanotubes in promoting the properties of carbon black-filled natural rubber/butadiene rubber composites. Results Phys 2017; 7: 4352–4358.

10.

Kato

Ikeda

Kohjiya

Reinforcement mechanism of carbon black (CB) in natural rubber vulcanizates: relationship between CB aggregate and network structure and viscoelastic properties. Polym Plast Technol Eng 2017; 1–12.

11.

Sahakaro

Mechanism of reinforcement using nanofillers in rubber nanocomposites. In: Prog Rub Nanocomp. Cambridge: Woodhead Publishing, 2017, pp.81–113.

12.

Kongvasana

Kositchaiyong

Wimolmala

et al . Fly ash particles and precipitated silica as fillers in NR/CR vulcanizates under thermal and thermal-oil ageing. Polym Adv Technol 2011; 22: 1014–1023.

13.

Sombatsompop

Wimolmala

Sirisinha

Fly ash particles and precipitated silica as fillers in rubbers. III. Cure characteristics and mechanical and oil-resistance properties of acrylonitrile-butadiene rubber. J Appl Polym Sci 2008; 110: 2877–2883.

14.

Subramaniam

Heinrich

Carbon nanotubes rubber composites. In: Kobayashi

Müllen

(eds) Encyclopedia of polymeric nanomaterials. Berlin, Heidelberg: Springer Berlin Heidelberg, 2015, pp.1–6.

15.

Jose

Moni

Salini

et al . Multifunctional multi-walled carbon nanotube reinforced natural rubber nanocomposites. Ind Crops Prod 2017; 105: 63–73.

16.

Bokobza

Multiwall carbon nanotube elastomeric composites: a review. Polymer 2007; 48: 4907–4920.

17.

Mostafa

Abouel-Kasem

Bayoumi

et al . Effect of carbon black loading on the swelling and compression set behavior of SBR and NBR rubber compounds. Mater Des 2009; 30: 1561–1568.

18.

Warasitthinon

Nanocomposites of nitrile (NBR) rubber with multi-walled carbon nanotubes. Ann Arbor: University of Massachusetts Lowell, 2013.

19.

Boonbumrung

Sae-Oui

Sirisinha

Reinforcement of multiwalled carbon nanotube in nitrile rubber: in comparison with carbon black, conductive carbon black, and precipitated silica. J Nanomater 2016; 2016: 1–8.

20.

Mitryaeva

Akimenko

SS.

Influence of multi-walled carbon nanotubes in carbon black mixture on rubber properties. Procedia Eng 2016; 152: 689–693.

21.

Pittayavinai

Thanawan

Amornsakchai

Manipulation of mechanical properties of short pineapple leaf fiber reinforced natural rubber composites through variations in cross-link density and carbon black loading. Polym Test 2016; 54: 84–89.

22.

Song

Zhang

Carbon nanotube/reduced graphene oxide hybrid for simultaneously enhancing the thermal conductivity and mechanical properties of styrene -butadiene rubber. Carbon 2017; 123: 158–167.

23.

Harris

PJF.

Carbon nanotube science: synthesis, properties and applications. New York: Cambridge University Press, 2009.

24.

Campo

Jiménez-Suárez

Ureña

Effect of type, percentage and dispersion method of multi-walled carbon nanotubes on tribological properties of epoxy composites. Wear 2015; 324–325: 100–108.

25.

Zhou

et al . A comparative study on wear behavior and mechanism of styrene butadiene rubber under dry and wet conditions. Wear 2016; 356–357: 1–8.

26.

Tharajak

Palathai

Sombatsompop

Recommendations for h-BN loading and service temperature to achieve low friction coefficient and wear rate for thermal-sprayed PEEK coatings. Surf Coat Technol 2017; 321: 477–483.