The temperature distribution of the mold is directly linked to the manufacturing quality of the composite component. In this paper, a bionic mold based on the analysis of a manta ray in swimming is developed to improve the thermal performance of the mold during the autoclave curing process. The bionic mold has fewer frames and better air permeability, and the mold weight is decreased by 42.95% while the stiffness is proved to satisfy the requirement. The model of the autoclave curing process which is verified by experiments is established to carry out the thermal analysis of the mold. Results show that the air velocity in the mold is increased with the bionic design, which can reduce not only the maximum temperature difference of the mold plate (−30.35%) but also the percentage of low-temperature areas. Besides, the heating rate and the heat preservation time of the mold are also improved.
YeYYZhuWDJiangJX, et al.Computational modelling of postbuckling behavior of composite T-stiffened panels with different bonding methods. Compos B Eng2019; 166: 247–256.
5.
ShahDBPatelKMPatelAI, et al.Experimental investigation on spring-back deformation during autoclave curing of parabolic antenna reflectors. Compos A Appl Sci Manuf2018; 115: 134–146.
6.
WeberTAArentJ-CMünchL, et al.A fast method for the generation of boundary conditions for thermal autoclave simulation. Compos A Appl Sci Manuf2016; 88: 216–225.
7.
YuanZYWangYJPengXQ, et al.An analytical model on through-thickness stresses and warpage of composite laminates due to tool–part interaction. Compos B Eng2016; 91: 408–413.
8.
MezeixLNasirMNMAminandaY, et al.Parameter study of tool-laminate interface through simulation for composite manufacturing using autoclave process. Appl Mech Mater2014; 606: 113–117.
9.
StarkWJaunichMMcHughJ. Dynamic mechanical analysis (DMA) of epoxy carbon-fibre prepregs partially cured in a discontinued autoclave analogue process. Polym Test2015; 41: 140–148.
10.
SunJGuYZLiM, et al.Effect of forming temperature on the quality of hot diaphragm formed C-shaped thermosetting composite laminates. J Reinf Plast Compos2012; 31: 1074–1087.
11.
AbdalrahmanRGroveSKyteA, et al.Numerical simulation and design optimisation of an integrally-heated tool for composite manufacturing. Mater Des2014; 64: 477–489.
12.
WeberTARuff-StahlH-JK. Advances in composite manufacturing of helicopter parts. Int J Aviat Aeronaut Aerosp2017; 4: 5.
13.
DiosMGonzalez-RPLDiosD, et al.A mathematical modeling approach to optimize composite parts placement in autoclave. Int Trans Oper Res2017; 24: 115–141.
14.
OlivierPCottuJPFerretB. Effects of cure cycle pressure and voids on some mechanical properties of carbon/epoxy laminates. Composites1995; 26: 509–515.
15.
GopalAKAdaliSVerijenkoVE. Optimal temperature profiles for minimum residual stress in the cure process of polymer composites. Compos Struct2000; 48: 99–106.
16.
ShahPHHallsVAZhengJQ, et al.Optimal cure cycle parameters for minimizing residual stresses in fiber-reinforced polymer composite laminates. J Compos Mater2018; 52: 773–792.
17.
KimJSLeeDG. Development of an autoclave cure cycle with cooling and reheating steps for thick thermoset composite laminates. J Compos Mater1997; 31: 2264–2282.
18.
WangXMZhangZGXieFY, et al.Correlated rules between complex structure of composite components and manufacturing defects in autoclave molding technology. J Reinf Plast Compos2009; 28: 2791–2803.
19.
KlugeNEJLundströmTSLjungA-L, et al.An experimental study of temperature distribution in an autoclave. J Reinf Plast Compos2016; 35: 566–578.
20.
WangQWangLYZhuWD, et al.Design optimization of molds for autoclave process of composite manufacturing. J Reinf Plast Compos2017; 36: 1564–1576.
21.
XieGNLiuJZangWH, et al.Simulation and improvement of temperature distributions of a framed mould during the autoclave composite curing process. J Engin Thermophys2013; 22: 43–61.
22.
WeberTAArentJ-CSteffensL, et al.Thermal optimization of composite autoclave molds using the shift factor approach for boundary condition estimation. J Compos Mater2017; 51: 1753–1767.
23.
ZobeiryNParkJPoursartipA. An infrared thermography-based method for the evaluation of the thermal response of tooling for composites manufacturing. J Compos Mater2019; 53: 1277–1290.
24.
ChenPLinAYMLinYS, et al.Structure and mechanical properties of selected biological materials. J Mech Behav Biomed Mater2008; 1: 208–226.
25.
LiangJHYangXBWangTM, et al.Design and experiment of a bionic gannet for plunge-diving. J Bionic Eng2013; 10: 282–291.
26.
WeiYLXuFBianSY, et al.Noise reduction of UAV using biomimetic propellers with varied morphologies leading-edge serration. J Bionic Eng2020; 17: 767–779.
27.
HudekM. Examination of Heat Transfer during Autoclave Processing of Polymer Composites. Canada: Master Thesis, University of Manitoba, 2001.
LowKHZhouCLSeetG, et al.Improvement and testing of a robotic manta ray (RoMan-III). In: 2011 IEEE international conference on robotics and biomimetics, Karon Beach, Thailand, 7-11 Dec. 2011: IEEE, 1730–1735.
34.
HuJZhanLHYangXB, et al.Temperature optimization of mold for autoclave process of large composite manufacturing. J Phys Conf Ser2020; 1549: 032086.
