To enhance the mechanical properties of compacted graphite iron (CGI), a novel as-cast niobium-microalloyed compacted graphite iron (L-Nb-CGI) was developed via the introduction of trace Nb. It was observed that Nb addition reduces graphite area and vermicularity in CGI, promotes pearlite formation, refines its lamellar spacing, and significantly improves the tensile strength and hardness of the material. Through comparative experiments involving multiple drilling parameter sets, along with analysis using ultra-depth-of-field and scanning electron microscopy, it was found that L-Nb-CGI demonstrates an average reduction of 16% in hole tearing factor and 8% in hole wall surface roughness under identical machining conditions compared to conventional RuTSi4Mo compacted graphite iron. Optimization of drilling parameters further inhibits hole surface damage, with the underlying mechanism explained as follows: increasing drill diameter to 10 mm enhances chip removal capacity; elevating spindle speed to 3000 r/min facilitates material thermal softening; and reducing feed per revolution to 0.1 mm/r effectively suppresses brittle fracture. The incorporation of Nb element effectively enhances the drilling quality of CGI, and drilling performance is improved through microstructure refinement and processing parameter optimization. The findings of this study offer theoretical and technological guidance for high-performance drilling applications of L-Nb-CGI.
LiuZQiXMaW, et al. Experimental investigation on fretting wear behaviors of compacted graphite cast iron under ball-disc contact. J Fail Anal Prev2024; 24: 58–70. https://doi.org/10.1007/s11668-023-01842-1
3.
ShiGQYangZLiJP, et al. Investigation into the evolution of microstructure and mechanical properties of compacted graphite iron under elevated temperature. J Mater Eng Perform2021; 30: 8479–8489. https://doi.org/10.1007/s11665-021-06068-6
4.
LinYHeSLaiD, et al. Wear mechanism and tool life prediction of high-strength vermicular graphite cast iron tools for high-efficiency cutting. Wear2020; 454-455: 203319. https://doi.org/10.1016/j.wear.2020.203319
5.
LiuQZhuGPangJ, et al. High-cycle fatigue properties prediction and damage mechanisms of RuT400 compacted graphite iron at different temperatures. Mater Sci Eng A2019; 764: 138248. https://doi.org/10.1016/j.msea.2019.138248
6.
ZhangMXPangJCQiuY, et al. Thermo-mechanical fatigue property and life prediction of vermicular graphite iron. Mater Sci Eng A2017; 698: 63–72. https://doi.org/10.1016/j.msea.2017.05.035
7.
PatelMDaveKUpadhyayG, et al. Assessment of compacted graphite iron viability for cost-effective product designing. J Inst Eng (India) Ser D2025; 106: 1117–1128. https://doi.org/10.1007/s40033-024-00702-y
8.
AiXTanJSunH, et al. Effect of tool coatings on machining properties of compacted graphite iron. Micromachines2022; 13(10): 1781. https://doi.org/10.3390/mi13101781
9.
DingYCaiMYuX. Comparison of joinery methods on the strength of joining aluminum alloy and steel parts in a vehicle. J Phys Conf Ser2022; 2386(1): 012093. https://doi.org/10.1088/1742-6596/2386/1/012093
10.
NingHLiXMengL, et al. Effect of Ni and Mo on microstructure and mechanical properties of grey cast iron. Mater Technol2023; 38(1): 2172991. https://doi.org/10.1080/10667857.2023.2172991
11.
KaymakKTazegülYKeyvanklıAB, et al. Effects of Ti addition and wall thickness on microstructure, hardness, and wear properties of spheroidal graphite cast irons. Tribol Int2024; 195: 109612. https://doi.org/10.1016/j.triboint.2024.109612
12.
HouYWangYPanZ, et al. Influence of rare earth nanoparticles and inoculants on performance and microstructure of high chromium cast iron. J Rare Earths2012; 30(3): 283–288. https://doi.org/10.1016/s1002-0721(12)60038-6
13.
ZhiXXingJFuH, et al. Effect of niobium on the as-cast microstructure of hypereutectic high chromium cast iron. Mater Lett2008; 62(6-7): 857–860. https://doi.org/10.1016/j.matlet.2007.06.084
14.
SunWTWangBLiuXL, et al. Controlling the tribology performance of gray cast iron by tailoring the microstructure. Tribol Int2022; 167: 107343. https://doi.org/10.1016/j.triboint.2021.107343
15.
PanSZengFSuN, et al. The effect of niobium addition on the microstructure and properties of cast iron used in cylinder head. J Mater Res Technol2020; 9(2): 1509–1518. https://doi.org/10.1016/j.jmrt.2019.11.076
16.
SuXZhouMZhuM, et al. Microstructure and mechanical properties of Nb microalloyed high-carbon pearlitic steels subjected to isothermal transformation. Mater Charact2023; 202: 113103. https://doi.org/10.1016/j.matchar.2023.113013
GaoWLLengYFuDF, et al. Effects of niobium and heat treatment on microstructure and mechanical properties of low carbon cast steels. Mater Des2016; 105(3): 114–123. https://doi.org/10.1016/j.matdes.2016.05.057
19.
SouzaTNFNogueiraRAPSFrancoFJS, et al. Mechanical and microstructural characterization of nodular cast iron (NCI) with niobium additions. Mater Res2014; 17: 1167–1172. https://doi.org/10.1590/1516-1439.249413
20.
SenthilPPRaoKSNandiHK, et al. Influence of niobium microalloying on the microstructure and mechanical properties of high carbon nano bainitic steel. Procedia Struct Integr2019; 14: 729–737. https://doi.org/10.1016/j.prostr.2019.05.091
21.
ChenXXuJHuH, et al. Effects of niobium addition on microstructure and tensile behavior of as- cast ductile iron. Mater Sci Eng A2017; 688: 416–428. https://doi.org/10.1016/j.msea.2017.01.032
22.
WuMChenYYuG, et al. Investigations on the axial cutting force during drilling of carbon fiber composite material. Proc Inst Mech Eng B J Eng Manuf2018; 232(13): 2430–2436. https://doi.org/10.1177/0954405417690569
23.
UysalA. Effects of cutting parameters on drilling performance of carbon black–reinforced polymer composite. Proc Inst Mech Eng B J Eng Manuf2018; 232(7): 1133–1142. https://doi.org/10.1177/0954405416662084
24.
ChenDChenYXuJ, et al. Research on deep hole drilling of nickel-based superalloy with low-frequency vibration: chip evacuation characteristic, chip formation and surface morphology. J Manuf Process2025; 140: 241–261. https://doi.org/10.1016/j.jmapro.2025.02.058
25.
AfzalMZKhanSAKhanAM, et al. Wear behavior of novel CVD-coated wiper inserts’ with various chip-breakers and resulting surface integrity during dry drilling of Ti-6Al-4V. Tribol Int2025; 202: 110323. https://doi.org/10.1016/j.triboint.2024.110323
26.
UcunİKaplanS. Determination of tool wear and chip formation in drilling process of AISI 1045 material using plasma-nitrided high-speed steel drill bits. Proc Inst Mech Eng B J Eng Manuf2017; 231(10): 1725–1734. https://doi.org/10.1177/0954405415608105
27.
SooSLAbdelhafeezAMLiM, et al. The drilling of carbon fibre composite–aluminium stacks and its effect on hole quality and integrity. Proc Inst Mech Eng B J Eng Manuf2019; 233(4): 1323–1331. https://doi.org/10.1177/0954405417728312
ChenWC. Some experimental investigations in the drilling of carbon fiber-reinforced plastic (CFRP) composite laminates. Int J Mach Tools Manuf1997; 37(8): 1097–1108. https://doi.org/10.1016/s0890-6955(96)00095-8
30.
QiuXYLiPNTangLY, et al. Determination of the optimal feed rate for step drill bit drilling CFRP pipe based on exit damage analysis. J Manuf Process2022; 83: 246–256. https://doi.org/10.1016/j.jmapro.2022.09.002
31.
ShuklaSJainRGangopadhyayS. Measurement and analysis of radial force, radial torque and surface integrity in micro-drilling of an Al7075-T6 alloy. Proc Inst Mech Eng B J Eng Manuf2024; 238(8): 1183–1195. https://doi.org/10.1177/09544054231189104
32.
LiYJiaoFZhangZ, et al. A prediction model for drilling temperature of CFRP/Ti stacks and green cooling strategy considering chip ejection process. J Mater Process Technol2024; 329: 118424. https://doi.org/10.1016/j.jmatprotec.2024.118424
33.
XuJAnQChenM. An experimental investigation on cutting-induced damage when drilling high-strength T800S/250F carbon fiber–reinforced polymer. Proc Inst Mech Eng B J Eng Manuf2017; 231(11): 1931–1940. https://doi.org/10.1177/0954405415619348
34.
ZhangWDuHZhouH, et al. Study of burr and tear defects at the entrance and exit surface during drilling of Kevlar composites. AIP Adv2025; 15(5): 1–9. https://doi.org/10.1063/5.0230484
35.
AamirMGiasinKTolouei-RadM, et al. Effect of cutting parameters and tool geometry on the performance analysis of one-shot drilling process of AA2024-T3. Metals2021; 11(6): 854. https://doi.org/10.3390/met11060854
36.
RaoKVRameshC. Modeling of tool vibration and its effect on roundness and surface roughness of hole in helical milling of Inconel 718. J Vib Control2022; 28(1-2): 159–168. https://doi.org/10.1177/1077546320974236
37.
FaridAASharifSIdrisMH. Surface integrity study of high-speed drilling of Al–Si alloy using HSS drill. Proc Inst Mech Eng B J Eng Manuf2011; 225(7): 1001–1007. https://doi.org/10.1177/2041297510393642
38.
Al-TameemiHAAl-DulaimiTAweMO, et al. Evaluation of cutting-tool coating on the surface roughness and hole dimensional tolerances during drilling of Al6061-T6 51 alloy. Materials2021; 14(7): 1783. https://doi.org/10.3390/ma14071783
39.
KiswantoGZariatinDLKoTJ. The effect of spindle speed, feed-rate and machining time to the surface roughness and burr formation of aluminum alloy 1100 in micro-milling operation. J Manuf Process2014; 16(4): 435–450. https://doi.org/10.1016/j.jmapro.2014.05.003
40.
KuoCLSooSLAspinwallDK, et al. Tool wear and hole quality when single-shot drilling of metallic-composite stacks with diamond-coated tools. Proc Inst Mech Eng B J Eng Manuf2014; 228(10): 1314–1322. https://doi.org/10.1177/0954405413517388
41.
GiasinKAyvar-SoberanisS. An investigation of burrs, chip formation, hole size, circularity and delamination during drilling operation of GLARE using ANOVA. Compos Struct2017; 159: 745–760. https://doi.org/10.1016/j.compstruct.2016.10.015
42.
ZhangXChenJWangH, et al. Mechanisms of defect formation and evolution in drilling thermoplastic CF/PEEK composite using twist and step drills. Compos Struct2025; 355: 118833. https://doi.org/10.1016/j.compstruct.2024.118833
