The effects of radial inlet with splitters on the performance of variable inlet guide vanes in a centrifugal compressor stage

Abstract

Variable inlet guide vanes (VIGVs) can regulate pressure ratio and mass flow at constant rotational speed in centrifugal compressors as a result of inducing a controlled prewhirl in front of impellers. Radial inlets and VIGVs are typical upstream components in front of the first-stage impellers in many industrial centrifugal compressors. However, previous investigations on VIGVs in centrifugal compressors were mostly conducted under the condition of axial inlets, and this study aims to focus on the effects of radial inlet on the VIGVs performance of a centrifugal compressor stage. The axial inlet stage model is compared with the radial inlet stage model with splitters using numerical flow simulation. The flow from the radial inlet was non-uniform in both circumferential and radial directions; thus, the VIGVs, the impeller, the vaneless diffuser, and the return vane channel are modelled with fully 360° passages. The three-dimensional (3D) flow field is numerically simulated at VIGVs setting angles ranging from - 20° to 60°. The overall stage performance parameters are obtained by integrating the field quantities. Though the splitters are equipped in the radial inlet, the overall stage polytropic efficiency decreases by an average of 4 per cent and total pressure ratio decreases by an average of 3.3per cent in comparison with the axial stage model. This can be attributed to the effect of both flow non-uniformity induced by radial inlet and flow loss in the radial inlet at different VIGV setting angles. The flow loss in the radial inlet with splitters is the main reason of the stage performance decrease compared with the flow non-uniformity. The simulation results show that the performance of VIGVs is degraded by its inlet flow distortions resulting from a radial inlet. The results in this study can be applied to centrifugal compressor design and optimization.

Keywords

radial inlet variable inlet guide vanes centrifugal compressor stage

Get full access to this article

View all access options for this article.

References

Lüdtke

K. H.

Process centrifugal compressors: basics, function, operation, design, application, 2004, 113–133 (Springer-Verlag, Berlin).

Wallace

F. J.

Whitfield

Atkey

R. C.

Experimental and theoretical performance of a radial flow turbocharger compressor with inlet prewhirl. Proc. Instn. Mech. Engrs., 1975, 189, 177–186.

Pampreen, R. C. The use of variable inlet guide vanes for automotive gas turbine engine augmentation and load control. SAE paper no. 760285, 1976.

Wagner, C. E. and Pampreen, R. C. Baseline automotive gas turbine engine development program final report. NASA CR-159670, N80-24620, 1979 (Chrysler Corporation, Highland Park, Michigan, USA).

Simon

Wallmann

Monk

Improvements in performance characteristics of single-stage and multistage centrifugal compressors by simultaneous adjustments of inlet guide vanes and diffuser vanes. J. Turbomach. Trans. ASME, 1987, 109(1), 41–47.

Rodgers

Centrifugal compressor inlet guide vanes for increased surge margin. J. Turbomach. Trans. ASME, 1991, 113(4), 696–702.

Joslyn, D. Experimental study of centrifugal compressor performance with axial inlet guide vanes. UTRC Report R92-491019-1, 1992 (United Technologies Research Center, East Hartford, Connecticut, USA).

Swain

The design of an inlet guide vane assembly for an industrial centrifugal compressor. Energy saving in the design and operation of compressors, 1996, 11–22 (Mechanical Engineering Publications Limited, London).

Kassens

Rautenberg

Flow measurements behind the inlet guide vane of a centrifugal compressor. 1998, In. Proceedings of the 1998 International Gas Turbine & Aeroengine Congress & Exhibition, 2–5 June, Stockholm, Sweden, paper no. 98-GT-86 (ASME, New York, USA).

10.

Chen

N. Y.

Hagelstein

Kassens

Overshoot of the Rankine vortex formed in the flow field behind the inlet guide vane of centrifugal compressors. 1999, Proceedings of the 1999 International Gas Turbine & Aeroengine Congress & Exhibition, 7–10 June, Indianapolis, USA, paper no. 99-GT-182 (ASME, New York, USA).

11.

Chen

N. Y.

Hagelstein

Kassens

Effect ofthe decaying overshoot of the Rankine vortex on the axial flow field behind the inlet guide vane ofcentrifugal compressors. 2000, Proceedings of ASME TURBOEXPO 2000, 8–10 May, Munich, Germany, paper no. 2000-GT-427 (ASME, New York, USA).

12.

Coppinger

Swain

Performance prediction of an industrial centrifugal compressor inlet guide vane system. Proc. IMechE, Part A: J. Power and Energy, 2000, 214(A2), 153–164.

13.

Zhou

Cai

Experimental study on the influence of diffuser and inlet guide vane for the performance of centrifugal compressor. Exp. Tech., 2008, 32(5), 26–33.

14.

Flathers

M. B.

Bache

G. E.

Rainsberger

An experimental and computational investigation of flow in a radial inlet of an industrial pipeline centrifugal compressor. J. Turbomach. Trans. ASME, 1996, 118(2), 371–384.

15.

Koch

J. M.

Chow

P. N.

Hutchinson

B. R.

Elias

S. R.

Experimental and computational study of a radial compressor inlet. 1995, In Proceedings of the 1995 International Gas Turbine & Aeroengine Congress & Exhibition, 5–8 June, Houston, USA, paper no. 95-GT-82 (ASME, New York, USA).

16.

Michelassi

Giachi

Experimental and numerical analysis of compressor inlet volutes. 1997, In Proceedings of the 1997 International Gas Turbine & Aeroengine Congress & Exhibition, 2–5 June, Orlando, USA, paper no. 97-GT-481 (ASME, New York, USA).

17.

Pazzi

Michelassi

Analysis and design outlines of centrifugal compressor inlet volutes. 2000, In. Proceedings of ASME TURBOEXPO 2000, 8–11 May, Munich, Germany, paper no. 2000-GT-0464 (ASME, New York, USA).

18.

Michelassi

Pazzi

Echtner

Performance of centrifugal compressor impellers in steady and unsteady flow regimes under inlet flow distortions. 2001, In Proceedings of ASME TURBOEXPO 2001, 4–7 May, New Orleans, USA, paper no. 2001-GT-0325 (ASME, New York, USA).

19.

Cui

M. M.

Effect of suction elbow and inlet guide vanes on flow field in a centrifugal compressor stage. 2002, In Proceedings of ASME TURBOEXPO 2002, 3–6 June, Amsterdam, Netherlands, paper no. GT2002-30376 (ASME, New York, USA).

20.

Engeda

Kim

Aungier

Direnzi

The inlet flow structure of a centrifugal compressor stage and its influence on the compressor performance. J.Fluids Eng. Trans. ASME, 2003, 125(5), 779–785.

21.

Fatsis

Pierret

Van den Braembussche

Three-dimensional unsteady flow and forces in centrifugal impellers with circumferential distortion of the outlet static pressure. J. Turbomach. Trans. ASME, 1997, 119(1), 94–102.

22.

Wang

Mao

Synthetically aerodynamic design and optimization on the stationary units of centrifugal compressor. 2009, In Proceedings of ASME FEDSM 2009, 2–6 August, Colorado, USA, paper no. FEDSM2009-78096 (ASME, New York, USA).

23.

Shenyang Blower Works. The test report of large flow centrifugal compressor model stage for SBW (in Chinese). SBW Report No. 86J3001, 1990.

24.

Zhang

Mao

Experimental investigation and improvement of the inlet guide vane with plate vane in a centrifugal fan. Proc. IMechE, Part A: J. Power and Energy, 2009, 223(A4), 401–413.

25.

Zhang

Tan

Mao

Experimental study on inlet guide vane with straight blade in a centrifugal fan (in Chinese). J. Xi. Jiao. Univ., 2007, 41(9), 1044–1048.

26.

Zhang

Tan

Mao

Experimental study on performance of inlet guide vane with improvement of blade airfoil and cascade solidity (in Chinese). J. Xi. Jiao. Univ., 2008, 42(5), 583–587.

27.

Wang

Zhang

Numerical study on the interior flow in the radial inlet volute for centrifugal compressor (in Chinese). Fluid Mach., 2008, 36(6), 19–24.

28.

Wang

Mao

Flow loss for the radial inlet volute of centrifugal compressor improved design (in Chinese). Chin. J. Appl. Mech., 2009, 26(3), 437–443.