Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining

Abstract

Powder-mixed electrical discharge machining (PMEDM) is the technique of using dielectric fluid mixed with various types of powders to improve the machined surface output. This process is fast gaining prominence in electrical discharge machining (EDM) industry. The objective of this investigation is to determine the ability of tantalum carbide (TaC) powder-mixed dielectric fluid to enhance the surface properties of stainless steel material during EDM. The properties investigated are the micro-hardness and corrosion characteristics of the EDMed surface. Machining was conducted with 25.0 g/L concentration of TaC powder in kerosene dielectric fluid. The machining variables used were the peak current, pulse on time and the pulse off time. The effects of these variables on the micro-hardness of the EDMed surface were determined. Corrosion tests were also conducted on the samples that exhibited higher hardness. Results showed that the EDMed surface was alloyed with elements from the TaC powder. The highest micro-hardness obtained with PMEDM is about 1,200 Hv. This is about 1.5 times that obtained without TaC powder in the dielectric fluid. The loss in weight during corrosion test was found to be 0.056 µg/min for the PMEDM which was much lower than the lowest value of 10.56 µg/min obtained for the EDM without powder dielectric fluid.

Keywords

Powder-mixed electrical discharge machining micro-hardness tantalum carbide powder SUS 304 stainless steel corrosion

Get full access to this article

View all access options for this article.

References

Yan

Huang

. Improvement of surface finish on SKD steel using electro–discharge machining with aluminium and surfactant added dielectric. Int J Mach Tools Manuf 2005; 45: 1195–1201.

Zhao

Meng

Wang

. The application of research on powder mixed EDM in rough machining. J Mater Process Technol 2002; 129: 30–33.

Tzeng

Lee

. Effects of powder characteristics on electro discharge machining efficiency. Int J Adv Manuf Technol 2001; 17: 586–592.

Kumar

Masheshwari

Sharma

. Research developments in additives mixed electrical discharge machining (AEDM): a state of art review. Mater Manuf Process 2010; 25: 1166–1180.

Ojha

Garg

Singh

. The effect of nickel micro powder suspended dielectric on EDM performance measures of EN-19 steel. J Eng Appl Sci 2011; 6: 27–37.

Jahan

Rahman

Wong

. Study on the nano-powder-mixed sinking and milling micro-EDM of WC-Co. Int J Adv Manuf Technol 2011; 53: 167–180.

Khan

Ndaliman

Zain

. Surface modification using electric discharge machining (EDM) with powder addition. Appl Mech Mater 2012; 110–116: 725–733.

Kuang

Jenn

. Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide. Int J Adv Manuf Technol 2009; 40: 95–104.

Singh

Kumar

Beri

. Some experimental investigation of aluminium powder mixed EDM on machining performance of hastelloy steel. Int J Adv Eng Technol 2010; 1(2): 28–45.

10.

Sharma

Kumar

Beri

. Effect of aluminum powder addition in dielectric during EDM of hastelloy on machining performance using reverse polarity. Int J Adv Eng Technol 2010; 1(3): 13–24.

11.

Kumar

Maheshwari

Sharma

. Realizing potential of graphite powder in enhancing machining rate in AEDM of nickel based super alloy 718. Proc Conf Adv Mech Eng 2010. DOI: 02.AMAE.2010.01.51.

12.

Sharma

Kumar

Beri

. Study of tool wear rate during powder mixed electrical discharge machining of hastelloy steel. Int J Adv Eng Technol 2011; 2(2): 133–139.

13.

Chatha SS, Bhatia R, Sidhu HS, et al. Impact of added titanium oxide in dielectric of EDM on surface characteristics and MRR. In: Proc. Nat. Conf. Advancements and Futuristics Trends in Mech. Mater. Eng., Talwandi Sabo, 19–20 February 2010.

14.

Pecas

Henriques

. Influence of silicon powder–mixed dielectric on conventional electrical machining. Int J Mach Tools Manuf 2003; 43: 1465–1471.

15.

Kansal

Singh

Kumar

. Performance parameters optimization (multi characteristics) of powder mixed dielectric discharge machining (PMEDM) through Taguchi’s method and utility concept. Indian J Eng Mater Sci 2006; 13: 209–216.

16.

Furutani

Saneto

Takezawa

. Accretion of titanium carbide in electrical discharge machining with powder suspended in working fluid. Precis Eng 2001; 25: 138–144.

17.

Furutani

Shimizu

. Experimental analysis of deposition process of lubricant surface by electrical discharge machining with molybdenum disulfide powder suspended in working oil. Int J Mach Tools Manuf 2002; 43: 1287–1300.

18.

Ndaliman MB, Khan AA and Zain ZM. Performance of PM compacted Cu-TaC electrodes during EDM. In: Presented at the 2nd Int. Conf. Mech. Manuf. Eng. (ICME 2011), PICC, Putrajaya, Malaysia, 6–8 June 2011.

19.

Ndaliman

Khan

Ali

. Surface modification of titanium alloy through electrical discharge machining (EDM). Int J Mech Mater Eng 2011; 6: 380–384.

20.

Zain

Ndaliman

Khan

. Electro-discharge machining of SUS 304 stainless with TaC powder-mixed dielectric. Adv Mater Res 2012; 576: 72–75.

21.

Chen

Yan

Huang

. Influence of kerosene and distilled water as dielectric on the electrical discharge machining characteristics of Ti-6Al-4V. J Mater Process Technol 1999; 87: 107–111.

22.

Ndaliman

Khan

Ali

. Influence of electrical discharge machining process parameters on surface micro-hardness of titanium alloy. Proc IMechE, Part B: J Engineering Manufacture 2013; 227(3): 460–464.

23.

Ndaliman

Khan

Ali

. Influence of dielectric fluids on surface properties of electrical discharge machined titanium alloy. Proc IMechE, Part B: J Engineering Manufacture 2013; 227(9): 1310–1316.

24.

Ndaliman

Khan

Ali

. Formation of nitrides and carbides on titanium alloy surface through EDM. Adv Mater Res 2012; 576: 7–10.

25.

Abdulkareem

Khan

Konneh

. Cooling effect on electrode and process parameters in EDM. Mater Manuf Process 2010; 25: 462–466.