Custom design of furniture elements by fused filament fabrication

Abstract

Additive manufacturing technologies enable rapid prototyping of different parts, according to the three-dimensional model software solution. This paper presents some aspects of fused deposition modeling technology and its application in the wood industry. The fused deposition modeling technology was initially developed for three-dimensional printing of plastic parts, whereas acrylonitrile butadiene styrene and polylactic acid plastics filament are commonly applied. Possibilities for application of different composites with fused deposition modeling in the wood industry are reviewed and presented in this paper. Several industrial applications were considered also, from aspects of material durability, mechanical strength, low cost, and customization. Directions of further research have been discussed, considering graphene and carbon nanotubes as composite reinforcement materials and bio-organic composites with wooden particles or fibers mixed into the polymer matrix. Development of new composites for use with the fused deposition modeling technology is promising area taking into account that new low-cost extruders are already commercially available, as a support to fused deposition modeling device. Three-dimensional printing is very convenient for investigation of different custom-made composite materials, as well as custom shapes of final parts, starting from powders, their mixing, drawing of composite material filament, which are further used for three-dimensional printing with solidification and fabrication of custom-made products. New composites for fused deposition modeling, made of wood and plastic combinations were experimentally investigated for use as functional and customized elements of furniture. Obtained results strongly indicated that both new composite materials and fused deposition modeling printing can be efficiently used for broad customization from aspects of material properties and product shapes, thus enabling low-cost fabrication of small series of complex furniture elements, especially fixtures or clamp tools.

Keywords

3D print fused deposition modeling fused filament fabrication wood plastic composites furniture custom fixtures

Get full access to this article

View all access options for this article.

References

Taylor

. Fatigue-resistant components: What can we learn from nature? Proc IMechE, Part C: J Mechanical Engineering Science 2015; 229: 1186–1193.

Davies

Clarke

. Design and manufacture of components for motor sport using computer-aided design and rapid casting technology. Proc IMechE, Part C: J Mechanical Engineering Science 2013; 227: 2751–2761.

Velu

Singamneni

. Evaluation of the influences of process parameters while selective laser sintering PMMA powders. Proc IMechE, Part C: J Mechanical Engineering Science 2015; 229: 603–613.

Raney

Lewis

. Printing mesoscale architectures. MRS Bull 2015; 40: 943–950.

Farahani

Chizari

Therriault

. Three-dimensional printing of freeform helical microstructures: A review. Nanoscale 2014; 6: 10470–10485.

Gao

Zhang

Ramanujan

. The status, challenges, and future of additive manufacturing in engineering. CAD Comput Aid Des 2015; 69: 65–89.

Babu

Goodridge

. Additive manufacturing. Mater Sci Technol 2015; 8: 881–883.

Gebhardt

. Understanding additive manufacturing, Munich: Carl Hanser, 2011, pp. 31–65.

Fastermann

. 3D-Druck / Rapid Prototyping Eine Zukunftstechnologie – kompakt erklärt, Berlin-Heidelberg: Springer, 2012, pp. 117–127.

10.

Ruan J, Sparks TE, Fan Z, et al. A review of layer based manufacturing processes for metals. Solid Freeform Fabrication Symposium, Faculty Research & Creative Works, http://scholarsmine.mst.edu, 2006.

11.

Chen

Tsang

Albrecht

3-D fabrication technology for tissue engineering. In: Ferrari

Desai

Bhatia

(eds). BioMEMS and biomedical nanotechnology, New York: Springer, 2007, pp. 23–38.

12.

Narayan

. Rapid prototyping of biomaterials, Cambridge: Woodhead Publishing Limited, 2014, pp. 1–16.

13.

Thomas

. Costs, benefits, and adoption of additive manufacturing: A supply chain perspective. Int J Adv Manuf Technol 2015.

14.

Jin

Y-A

. Quantitative analysis of surface profile in fused deposition modelling. Addit Manuf 2015; 8: 142–148.

15.

Dudek

. FDM 3D printing technology in manufacturing composite elements. Arch Metall Mater 2013; 58: 1415–1418.

16.

Boschetto

Bottini

. Accuracy prediction in fused deposition modeling. Int J Adv Manuf Technol 2014; 73: 913–928.

17.

Kumar

Singh

Ahuja

IPS

. Investigations on dimensional accuracy of the components prepared by hybrid investment casting. J Manuf Process 2015; 20: 525–533.

18.

Malinauskas

Rekštyte

Lukoševičius

. 3D microporous scaffolds manufactured via combination of fused filament fabrication and direct laser writing ablation. Micromachines 2014; 5: 839–858.

19.

Prüß

Vietor

. Design for fiber-reinforced additive manufacturing. Trans ASME J Mech Des 2015; 137: 115001–115001.

20.

Roberson

Shemelya

MacDonald

. Expanding the applicability of FDM-type technologies through materials development. Rapid Prototyp J 2015; 21: 137–143.

21.

Masood

Advances in fused deposition modeling. In: Hashmi

(ed). Comprehensive materials processing, New York: Elsevier, 2014, pp. 69–91.

22.

Monfared

Mondali

Abedian

. Steady-state creep analysis of polymer matrix composites using complex variable method. Proc IMechE, Part C: J Mechanical Engineering Science 2013; 227: 2182–2194.

23.

Zhang

. The effects of adding carbon nanotubes to the mechanical and tribological properties of a carbon fibre reinforced polyether ether ketone composite. Proc IMechE, Part C: J Mechanical Engineering Science 2009; 223: 2501–2507.

24.

Panigrahi S, Rana A, Kushwaha RL, et al. Biodegradable green composite boards for industrial application. In: Commercial vehicle engineering congress and exhibition, Rosemont, IL, USA, 7–9 October 2008, SAE Technical Papers, Code 90793.

25.

Hwang

Reyes

Moon

K-S

. Thermo-mechanical characterization of metal/polymer composite filaments and printing parameter study for fused deposition modeling in the 3D printing process. J Electron Mater 2015; 44: 771–777.

26.

Torrado

Shemelya

English

. Characterizing the effect of additives to ABS on the mechanical property anisotropy of specimens fabricated by material extrusion 3D printing. Addit Manuf 2015; 6: 16–29.

27.

Otero-Neira

Lindman

Fernández

. Innovation and performance in SME furniture industries: An international comparative case study. Market Intell Plan 2009; 27: 216–232.

28.

Wu S-H and Ho M-C. A study of the combination of traditional craft and modern design in bamboo furniture. –In: Proceedings of the 3rd international conference on innovation, communication and engineering, ICICE 2014, Guiyang, Guizhou, China, 17–22 October 2014; Code 137669, 2015, pp.373–378.

29.

Matta AK, Ranga Raju D and Suman KNS. The integration of CAD/CAM and rapid prototyping in product development: A review. Mater Today 2015; 2: 3438–3445.

30.

Jain

Kuthe

. Feasibility study of manufacturing using rapid prototyping: FDM approach. Procedia Eng 2013; 63: 4–11.

31.

Nikolay

Kollenberg

. Customized kiln furniture. InterCeram: Int Ceram Rev 2011; 60: 208–210.

32.

Klahn C, Leutenecker B and Meboldt M. Design strategies for the process of additive manufacturing. In: Procedia CIRP, 25th design conference innovative product creation, CIRP 2015, Haifa, Israel, 2–4 March 2015, pp.230–235.

33.

Klahn C, Leutenecker B and Meboldt M. Design for additive manufacturing - Supporting the substitution of components in series products. In: Procedia CIRP, 24th CIRP design conference 2014: Mass customization and personalization, Pirelli, Lombardy Region Palace, Milano, Italy, 14–16 April 2014, pp.138–143.

34.

Ibrahim

Badrishah

Sa’ude

. Sustainable natural bio composite for FDM feedstocks. Appl Mech Mater 2014; 607: 65–69.

35.

Zhao H, Zhu HY, Zhou YL, et al. Research of wood plastic composites application based on fused deposition modeling technology. In: Proceedings of 2011 international conference on electronic and mechanical engineering and information technology, EMEIT 2011, 2011, pp.1560–1562.

36.

Sljivic M, Grujovic N, Pavlovic A, et al. Developing profiles from wood-plastic composites. In: International conference on accomplishments in electrical and mechanical engineering and information technology, DEMI 2015, Banja Luka, 2015.

37.

Taufik

Jain

. A study of build edge profile for prediction of surface roughness in fused deposition modeling. J Manuf Sci Eng 2016; 138: 4032193–4032193.

38.

Kumar

. An experimental and theoretical investigation of surface roughness of poly-jet printed parts: This paper explains how local surface orientation affects surface roughness in a poly-jet process. Virtual Phys Prototyp 2015; 10: 23–34.

39.

Boschetto

Bottini

. Roughness prediction in coupled operations of fused deposition modeling and barrel finishing. J Mater Process Technol 2015; 219: 181–192.

40.

Boschetto

Giordano

Veniali

. 3D roughness profile model in fused deposition modelling. Rapid Prototyp J 2013; 19: 240–252.

41.

Pham

Dimov

. Rapid prototyping and rapid tooling - the key enablers for rapid manufacturing. Proc IMechE, Part C: J Mechanical Engineering Science 2003; 217: 1–23.

42.

Hague

Campbell

Dickens

. Implications on design of rapid manufacturing. Proc IMechE, Part C: J Mechanical Engineering Science 2003; 217: 25–30.