Effect of cutting edge geometry change due to tool wear on hole quality in drilling of carbon fiber reinforced plastics using advanced ceramic coated tools
Restricted accessResearch articleFirst published online January, 2022
Effect of cutting edge geometry change due to tool wear on hole quality in drilling of carbon fiber reinforced plastics using advanced ceramic coated tools
This paper aims to study the evolution of cutting edge geometry due to tool wear and discuss its impact on the hole quality of a carbon fiber reinforced plastic (CFRP) laminate. A drilling experiment was conducted using three types of twist drills: uncoated, BAM (AlMgB14) coated, and (AlCrSi/Ti)N nanocomposite coated tungsten carbide tools. After generating 120 holes, the uncoated drill had the largest cutting edge radius (∼36 µm), while the BAM coated drill had the most extensive flank wear (∼287 µm) among the three drills. This relatively rapid tool wear results in a reduction of average hole size and a considerable variation on the hole profiles. The worn drills with the cutting edge radius greater than 19.3 µm form the fiber pull-outs in not only the 135° plies but also the adjacent 45° and 90° plies from the cutting direction, creating deep void networks. This type of networked fiber pull-out damage was observed with the holes machined by the uncoated and BAM coated drills. The (AlCrSi/Ti)N coated drill, which experienced the least amount of flank wear and the least increase of cutting edge radius, generated consistently sized holes up to 120 holes. However, the relatively sharp (AlCrSi/Ti)N coated tool results in the higher arithmetic roughness average (Ra) and the maximum roughness height (Rz) values than the other tools due to the localized fiber pull-outs and the absence of severe matrix smearing.
ThakurAPal SinghASharmaM.Mechanics of delamination-free drilling in polymer matrix composite laminates: a review. Proc IMechE, Part C: J Mechanical Engineering Science2021; 235(1): 095440622093482.
2.
BarikTPalKParimitaS, et al. Monitoring of hole surface integrity in drilling of bi-directional woven carbon fiber reinforced plastic composites. Proc IMechE, Part C: J Mechanical Engineering Science2020; 234: 2432–2458.
3.
ParkK-HBealA.A comparative study of carbide tools in drilling of CFRP and CFRP-Ti stacks. J Manuf Sci Eng2014; 136: 014501(1-9).
4.
ZitouneRKrishnarajVSofiane AlmabouacifB, et al. Influence of machining parameters and new nano-coated tool on drilling performance of CFRP/aluminium sandwich. Compos Part B Eng2012; 43: 1480–1488.
5.
KimDBealAKwonP.Effect of tool wear on hole quality in drilling of carbon fiber reinforced plastic–titanium alloy stacks using tungsten carbide and polycrystalline diamond tools. J Manuf Sci Eng2015; 138: 031006.
6.
LiuDTangYCongWL.A review of mechanical drilling for composite laminates. Compos Struct2012; 94: 1265–1279.
7.
WangFQianBJiaZ, et al. Secondary cutting edge wear of one-shot drill bit in drilling CFRP and its impact on hole quality. Compos Struct2017; 178: 341–352.
8.
MontoyaMCalamazMGehinD, et al. Evaluation of the performance of coated and uncoated carbide tools in drilling thick CFRP/aluminium alloy stacks. Int J Adv Manuf Technol2013; 68: 2111–2120.
9.
LiuJShaoXJLiuYJ, et al. The effect of holes quality on fatigue life of open hole. Mater Sci Eng A2007; 467: 8–14.
PerssonEErikssonIZackrissonL.Effects of hole machining defects on strength and fatigue life of composite laminates. Compos Part Appl Sci Manuf1997; 28: 141–151.
12.
JainSYangDCH.Effects of feedrate and chisel edge on delamination in composites drilling. J Eng Ind1993; 115: 398–405.
13.
SadatABChanWSWangBP.Delamination of graphite/epoxy laminate during drilling operation. J Energy Resour Technol1992; 114: 139–141.
14.
DurãoLTavaresJde AlbuquerqueV, et al. Drilling damage in composite material. Materials2014; 7: 3802–3819.
15.
RahimEAMohidZHamzahMR, et al. Performance of tools design when helical milling on carbon fiber reinforced plastics (CFRP) aluminum (Al) stack. Appl Mech Mater2013; 465–466: 1075–1079.
16.
StoneRKrishnamurthyK.A neural network thrust force controller to minimize delamination during drilling of graphite-epoxy laminates. Int J Mach Tools Manuf1996; 36: 985–1003.
17.
AbrãoAMRubioJCCFariaPE, et al. The effect of cutting tool geometry on thrust force and delamination when drilling glass fibre reinforced plastic composite. Mater Des2008; 29: 508–513.
18.
DavimJPReisP.Study of delamination in drilling carbon fiber reinforced plastics (CFRP) using design experiments. Compos Struct2003; 59: 481–487.
19.
DavimJPReisPAntónioCC.Experimental study of drilling glass fiber reinforced plastics (GFRP) manufactured by hand lay-up. Compos Sci Technol2004; 64: 289–297.
20.
DavimJRubioJAbraoA.A novel approach based on digital image analysis to evaluate the delamination factor after drilling composite laminates. Compos Sci Technol2007; 67: 1939–1945.
21.
GaitondeVNKarnikSRRubioJC, et al. Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites. J Mater Process Technol2008; 203: 431–438.
22.
Campos RubioJAbraoAMFariaPE, et al. Effects of high speed in the drilling of glass fibre reinforced plastic: evaluation of the delamination factor. Int J Mach Tools Manuf2008; 48: 715–720.
23.
XuJLiCMiS, et al. Study of drilling-induced defects for CFRP composites using new criteria. Compos Struct2018; 201: 1076–1087.
24.
XuJHuangXDavimJP, et al. On the machining behavior of carbon fiber reinforced polyimide and PEEK thermoplastic composites. Polym Compos2020; 41: 3649–3663.
25.
XuJLiCChenM, et al. An investigation of drilling high-strength CFRP composites using specialized drills. Int J Adv Manuf Technol2019; 103: 3425–3442.
26.
XuJHuangXChenM, et al. Drilling characteristics of carbon/epoxy and carbon/polyimide composites. Mater Manuf Process2020; 35: 1732–1740.
LiBZhangSYanZ, et al. Influence of edge hone radius on cutting forces, surface integrity, and surface oxidation in hard milling of AISI H13 steel. Int J Adv Manuf Technol2018; 95: 1153–1164.
29.
ZhaoTAgmellMPerssonJ, et al. Correlation between edge radius of the cBN cutting tool and surface quality in hard turning. J Superhard Mater2017; 39: 251–258.
30.
DenkenaBLucasABassettE.Effects of the cutting edge microgeometry on tool wear and its thermo-mechanical load. CIRP Ann2011; 60: 73–76.
31.
ZhouJMWalterHAnderssonM, et al. Effect of chamfer angle on wear of PCBN cutting tool. Int J Mach Tools Manuf2003; 43: 301–305.
32.
PiquetRFerretBLachaudF, et al. Experimental analysis of drilling damage in thin carbon/epoxy plate using special drills. Compos Part Appl Sci Manuf2000; 31: 1107–1115.
33.
RajDSKarunamoorthyL.Study of the effect of tool wear on hole quality in drilling CFRP to select a suitable drill for Multi-Criteria hole quality. Mater Manuf Process2016; 31: 587–592.
34.
Samuel RajDKarunamoorthyL.Performance of cryogenically treated WC drill using tool wear measurements on the cutting edge and hole surface topography when drilling CFRP. Int J Refract Met Hard Mater2019; 78: 32–44.
35.
Samuel RajDKarunamoorthyL.Cutting edge—flatting and roughness measurement—to monitor blunting and chipping of the drill cutting edge when drilling CFRP. Int J Adv Manuf Technol2017; 92: 953–968.
36.
TsaoCCHochengH.Effect of tool wear on delamination in drilling composite materials. Int J Mech Sci2007; 49: 983–988.
37.
GaugelSSripathyPHaegerA, et al. A comparative study on tool wear and laminate damage in drilling of carbon-fiber reinforced polymers (CFRP). Compos Struct2016; 155: 173–183.
38.
ÇelikALazogluIKaraA, et al. Wear on SiAlON ceramic tools in drilling of aerospace grade CFRP composites. Wear2015; 338–339: 11–21.
39.
FariaPECampos RubioJCAbrãoAM, et al. Dimensional and geometric deviations induced by drilling of polymeric composite. J Reinf Plast Compos2009; 28: 2353–2363.
40.
RawatSAttiaH.Wear mechanisms and tool life management of WC–Co drills during dry high speed drilling of woven carbon fibre composites. Wear2009; 267: 1022–1030.
41.
RamirezCPoulachonGRossiF, et al. Tool wear monitoring and hole surface quality during CFRP drilling. Proc CIRP2014; 13: 163–168.
42.
PoulachonGOuteiroJRamirezC, et al. Hole surface topography and tool wear in CFRP drilling. Proc CIRP2016; 45: 35–38.
43.
IsbilirOGhassemiehE.Comparative study of tool life and hole quality in drilling of CFRP/titanium stack using coated carbide drill. Mach Sci Technol2013; 17: 380–409.
44.
FeitoNDíaz-ÁlvarezJDíaz-ÁlvarezA, et al. Experimental analysis of the influence of drill point angle and wear on the drilling of woven CFRPs. Materials2014; 7: 4258–4271.
45.
FeitoNDiaz-ÁlvarezACanteroJL, et al. Experimental analysis of special tool geometries when drilling woven and multidirectional CFRPs. J Reinf Plast Compos2016; 35: 33–55.
46.
NguyenDBin AbdullahMSKhawarizmiR, et al. The effect of fiber orientation on tool wear in edge-trimming of carbon fiber reinforced plastics (CFRP) laminates. Wear2020; 450–451: 203213.
47.
InspektorABauerCEOlesEJ.Superhard coatings for metal cutting applications. Surf Coat Technol1994; 68–69: 359–368.
48.
KlockeFKriegT.Coated tools for metal cutting – features and applications. CIRP Ann1999; 48: 515–525.
49.
PrengelHGPfoutsWRSanthanamAT.State of the art in hard coatings for carbide cutting tools. Surf Coat Technol1998; 102: 183–190.
50.
NguyenDVoznyukVBin AbdullahMS, et al. Tool wear of superhard ceramic coated tools in drilling of CFRP/Ti stacks. Int Manuf Sci Eng Conf2019; 2: MSEC2019-2843 (1-9).
51.
SwanSBin AbdullahMSKimD, et al. Tool wear of advanced coated tools in drilling of CFRP. J Manuf Sci Eng2018; 140: 111018-111018–10.
52.
ShahabazSMShettyNShettySD, et al. Surface roughness analysis in the drilling of carbon fiber/epoxy composite laminates using hybrid Taguchi-Response experimental design. Mater Res Exp2020; 7: 015322.
53.
GiasinKGoreyGByrneC, et al. Effect of machining parameters and cutting tool coating on hole quality in dry drilling of fibre metal laminates. Compos Struct2019; 212: 159–174.
54.
WangXShenXYangG, et al. Evaluation of boron-doped-microcrystalline/nanocrystalline diamond composite coatings in drilling of CFRP. Surf Coat Technol2017; 330: 149–162.
55.
HarrisMQureshiMAMSaleemMQ, et al. Carbon fiber-reinforced polymer composite drilling via aluminum chromium nitride-coated tools: hole quality and tool wear assessment. J Reinf Plast Compos2017; 36: 1403–1420.
56.
ParkK-HBealAKimD(D-W, et al. Tool wear in drilling of composite/titanium stacks using carbide and polycrystalline diamond tools. Wear2011; 271: 2826–2835.
57.
TikalFHolstenS. Bedeutung der Kantenverrundung bei Zerspanungswerkzeugen. In: In-house trade fair 2008 of OTEC, Präzisionsfinish GmbH, 2008.
58.
UlutanDÖzelT.Determination of tool friction in presence of flank wear and stress distribution based validation using finite element simulations in machining of titanium and nickel based alloys. J Mater Process Technol2013; 213: 2217–2237.
59.
Alizadeh AshrafiSMillerPWandroK, et al. Characterization and effects of fiber pull-outs in hole quality of carbon fiber reinforced plastics composite. Materials2016; 9: 828.
60.
RamuluMKimDChoiG.Frequency analysis and characterization in orthogonal cutting of glass fiber reinforced composites. Compos Part Appl Sci Manuf2003; 34: 949–962.
61.
HudaAHNFAscroftHBarnesS.Machinability study of ultrasonic assisted machining (UAM) of carbon fibre reinforced plastic (CFRP) with multifaceted tool. Proc CIRP2016; 46: 488–491.
62.
EneyewEDRamuluM.Experimental study of surface quality and damage when drilling unidirectional CFRP composites. J Mater Res Technol2014; 3: 354–362.
63.
LandonYCherifM.Characterization of the surface quality of holes drilled in CFRP laminates. AMR2013; 698: 107–116.
64.
KlockeFSooSLKarpuschewskiB, et al. Abrasive machining of advanced aerospace alloys and composites. CIRP Ann2015; 64: 581–604.
65.
Vinu KumarSMSureshaBRajamuruganG, et al. Mechanical and abrasive wear behavior of cenosphere filled carbon reinforced epoxy composites using Taguchi-Grey relational analysis. Mater Res Exp2018; 6: 015307.
66.
Altin KarataşMGökkayaH.A review on machinability of carbon fiber reinforced polymer (CFRP) and glass fiber reinforced polymer (GFRP) composite materials. Def Technol2018; 14: 318–326.
67.
GiasinKAyvar-SoberanisS.Microstructural investigation of drilling induced damage in fibre metal laminates constituents. Compos Part Appl Sci Manuf2017; 97: 166–178.
68.
AbdullahMSBNguyenDKimD.A study of cutting edge geometry change and surface roughness in drilling of carbon fiber reinforced plastics (CFRP) using uncoated and coated tools. In: SAMPE 2020 virtual conference series, SAMPE 2020 Virtual Series, Advanced Design and Analysis, Society for the Advancement of Material and Process Engineering (SAMPE), Virtual, June 2020 2020; pp. 1–11. ■: ■.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
