Electrical connectors are widely used in electromechanical equipment. Their rough surfaces inevitably induce electrical contact resistance (ECR) and thermal contact resistance (TCR), which generates a significant influence on electricity and heat conducting at the faying surface and affects the accuracy of the thermal-electrical-mechanical coupling (TEMC) numerical calculation. Thus, a TEMC model with ECR and TCR of a parallel groove clamp is necessary to investigate the TEMC mechanism. Firstly, appropriate ECR and TCR models are created based on the available experimental results. Secondly, a refined TEMC finite element model is established by optimising the mesh size at the faying surfaces, and the cyclic coupling calculation method is adopted to achieve efficient and consistent numerical calculations. Meanwhile, the validity of the simulation model is verified by experimental results. Finally, the transient real contact area, current density, and heat generation rate (HGR) are obtained to analyse the TEMC mechanism during temperature rise. The results indicate that the mechanical characteristics during temperature rise are different under two loading conditions of tight and loose, thereby resulting in different changing laws in terms of the maximum current density and HGR. In addition, two coupling mechanisms exist until the steady-state temperature is achieved.
LiuXLCaiZBHeJF, et al. Effect of elevated temperature on fretting wear under electric contact. Wear2017; 376–377: 643–655.
2.
JiangXPanFShaoG, et al. Prediction of electrical contact endurance subject to micro-slip wear using friction energy dissipation approach. Friction2019; 7: 537–550.
3.
DongXCQuFRLiYF, et al. Simulation analysis and verification on three-dimensional temperature field of strain clamps for overhead lines. J Southwest Jiaotong Uni2019; 54: 997–1004.
4.
HeWFengYWuS, et al. Effect of elastoplastic thermal softening on thermal contact resistance based on the dual-load transfer coupling method. Int J Therm Sci2023; 183: 1–15.
5.
DaiYJRenXJWangYG, et al. Effect of thermal expansion on thermal contact resistance prediction based on the dual-iterative thermal–mechanical coupling method. Int J Heat Mass Transf2021; 173: 1–15.
6.
YanCWeiYXuC, et al. Experimental verification and electromagnetic–mechanics–acoustic field coupling analysis of transformer pressure relief valve malfunctions due to external short-circuit faults. IEEE Trans Magn2019; 55: 1–4.
7.
ChenMLiQZhangP.Experimental investigation of high temperature thermal contact resistance of thin disk samples using infrared camera in vacuum condition. Int J Heat Mass Transf2020; 157: 1–11.
8.
LiuZXieYYeX, et al. Numerical and experimental study of electromagnetic induction heating process for bolted flange joints. Proc Inst Mech Eng C2021; 235: 6357–6369.
9.
JiaXLinMSuS, et al. Numerical study on temperature rise and mechanical properties of winding in oil-immersed transformer. Energy2022; 239: 1–15.
10.
ZhangGWangHQingO, et al. Numerical analysis of multiphysical field for independent three-stage magnetorheological damper of double rod during recoil process of artillery. Proc Inst Mech Eng C2019; 233: 4960–4979.
11.
OzdemirVBKwokK.Electro-thermo-mechanical behavior of carbon nanopaper shape memory polymer composites. J Intell Mater Syst Struct2022; 33: 489–500.
12.
XuDPJiangYWKwonJH, et al. Analysis of the effects of electromagnetic circuit variables on sound pressure level and total harmonic distortion in a balanced armature receiver. IEEE Trans Magn2017; 53: 1–4.
13.
ZhangY.Improved numerical-analytical thermal modeling method of the PCB with considering radiation heat transfer and calculation of components temperature. IEEE Open2021; 9: 92925–92940.
14.
DoukasDIPapadopoulosTAChrysochosAI, et al. Multiphysics modeling for transient analysis of gas-insulated lines. IEEE Trans Power Deliv2018; 33: 2786–2793.
15.
MonnierAFroidurotBJarrigeC, et al. A mechanical, electrical, thermal coupled-field simulation of a sphere-plane electrical contact. IEEE Trans Compon Packaging Technol2007; 30: 787–795.
16.
PolchowJRAngadiSVJacksonRL, et al. A multi-physics finite element analysis of round pin high power connectors. In: Proceedings of the fifty-sixth IEEE Holm conference on electrical contacts, 2010, pp.30–38. New York: IEEE.
17.
HeWWangWWangZ, et al. Simulation and experimental study on temperature rise characteristic of a piercing connector. IEEE Trans Compon Packaging Technol2022; 12: 512–521.
18.
YaoSBLuoZWeiK, et al. Analysis of fluid-solid-thermal coupling characteristics of axial-symmetric vectoring exhaust nozzle. Proc Inst Mech Eng C2022; 236: 9472–9484.
19.
HashemiRPashazadehHHamediM.An incrementally coupled thermo-electro-mechanical model for resistance spot welding. Mater Manuf Process2012; 27: 1442–1449.
20.
WanZWangHPWangM, et al. Numerical simulation of resistance spot welding of Al to zinc-coated steel with improved representation of contact interactions. Int J Heat Mass Transf2016; 101: 749–763.
21.
LiWZhouLKongM, et al. Contact resistance modeling of sealed relay based on 3-D topography reduction. IEEE Trans Compon Packaging Technol2018; 8: 410–415.
22.
ZhangCRenW.Modeling of 3D surface morphologies for predicting the mechanical contact behaviors and associated electrical contact resistance. Tribol Lett2021; 69(1): 18.
23.
BrandtRNeuerG.Electrical resistivity and thermal conductivity of pure aluminum and aluminum alloys up to and above the melting temperature. Int J Thermophys2007; 28: 1429–1446.
24.
ZhanCZhuLZhangY, et al. A fully coupled model of multi-chip press-pack IGBT for thermo-mechanical stress distribution prediction. IEEE Trans Ind Appl2022; 58: 3852–3862.
25.
DengEZhaoZLinZ, et al. Influence of temperature on the pressure distribution within press pack IGBTs. IEEE Trans Power Electron2018; 33: 6048–6059.
26.
ZhangWNielsB.Finite element modeling aided process design in resistance welding. Liverpool. In: 8th int conf on computer techn in welding, 1998January.
27.
JamesPSChandlerHWEvansJT, et al. The effect of mechanical loading on the contact resistance of coated aluminium. Mater Sci Eng A1997; 230: 194–201.
28.
SongQFZhangWQBayN.An experimental study determines the electrical contact resistance in resistance welding. Weld J2005; 84: 73–76.
29.
RogeonPCarrePCostaJ, et al. Characterization of electrical contact conditions in spot welding assemblies. J Mater Process Technol2008; 195: 117–124.
30.
WangJWangHPLuF, et al. Analysis of Al-steel resistance spot welding process by developing a fully coupled multi-physics simulation model. Int J Heat Mass Transf2015; 89: 1061–1072.
31.
LuoDWangRYanY, et al. Comparison of different fluid-thermal-electric multiphysics modeling approaches for thermoelectric generator systems. Renew Energy2021; 180: 1266–1277.
32.
ZhangYMDengEPZhaoZB, et al. A review of the multiphysics coupling problem in press pack IGBT. Proc CSEE2019; 39: 6351–6364.
33.
HolmR.Electric contacts: theory and application. 4th ed.New York, NY: Springer, 1981, pp.65–66.
34.
BraunovicMMyshkinNKKonchitsVV.Electrical contacts fundamentals, applications and technology. London: Taylor & Francis Group, 2007, p.264.
HeWFengYWuS, et al. Effect of elastoplastic thermal softening on electrical contact resistance based on the dual-iterative coupling method. IEEE Trans Dielectr Electr Insul2023; 30: 11–19.
37.
FukuokaTXuQ.Evaluations of thermal contact resistance in an atmospheric environment. Trans Jpn Soc Mech Eng1999; 65: 248–253.
38.
FukuokaTNomuraM.Evaluation of thermal contact resistance at the interface composed of dissimilar materials. Trans Japan Soc Mech Eng A2010; 76: 344-350.
39.
I. ANSYS, ANSYS 15.0 help, Pennsylvania, USA, 2013.
40.
China Aviation Planning and Design Institute (Group), Ltd CO. Design manual for industrial and residential power supply and distribution. 4th ed.Beijing: China Electric Power Press, 2016, pp.50–52.
41.
GB/T 2317.3: 2008 Test method for electric power fittings-Part 3: Heat cycle tests for electric power fittings, Standards Press of China.
