Prediction of the pressure–flow characteristic of a Belleville washer-based damper valve

Abstract

Flow control valves used in automotive suspension dampers are almost universally based upon the restriction of flow using Belleville washers. These washers can best be described as a non-flat washer of conical shape and uniform thickness. They are also known as disc springs and are commonly used for load bearing in which their compactness and ability to produce a wide range of load–deflection characteristics provide an alternative to conventional coil springs. Due to the non-linear behaviour of Belleville washers, and the complex flow paths in an automotive damper valve, it is difficult to predict the resulting pressure–flow characteristic. As a result, damper valve design is often considered to be a ‘black art’ best carried out by an experienced engineer using an experimental-based trial-and-error approach. Clearly, without the aid of an analytical tool to predict the behaviour of prototype systems it is difficult for the designer to fully exploit the functionality of a particular design.

The current paper describes theoretical and experimental studies undertaken to investigate the pressure–flow characteristic of a Belleville washer-based damper valve. Existing load–deflection theory was extended to account for the hydraulic pressure acting on the surfaces of the washer. However, poor agreement was obtained between the measured pressure–flow data using a uniform pressure distribution across the washer diameter. For this reason the model was developed further to include the effect of a non-uniform pressure distribution within the valve. Computational fluid dynamics software was used to predict the pressure regime within the valve and this, in turn, was used to calculate the forces acting on the surface of the Belleville washer. The improved model was found to match the experimental behaviour with good accuracy, both for a range of spring pre-load conditions and for applications where several washers are stacked up in parallel. However further work would be required to develop a reliable simulation tool as an element of trial and error was necessary to estimate some simulation parameters.

Keywords

Belleville washer damper valve automotive suspension systems pressure–flow characteristics computational fluid dynamics simulation

Get full access to this article

View all access options for this article.

References

Patel

A study of gas suspension systems for off-road vehicles. PhD Thesis, Department of Mechanical Engineering, University of Bath, 2009.

Almen

J. O.

Laszlo

The uniform-section disk spring. Trans. Am. Soc. Mech. Engrs, 1936, 58, 305–314.

Curti

Orlando

A new calculation of coned annular disk spring. In Transactions of the ASME Winter Annual Meeting, ’Il filo metallico’, Chicago, Illinois, 27 January 1980, pp. 47--52 (ASME, New York).

Richards

C. W.

Tilley

D. G.

System analysis with Bathfp. Fluid Power, 1991, 3(March/April), 50–53.

Lichtarowicz

Flow and force characteristics of flapper valves. In Proceedings of the Internal Fluid Power Symposium, Turin, Italy, May 1973, vol. B1, pp. 1–24 (British Hydromechanics Research Association, Cranfield, UK).

Vaughan

N. D.

Johnston

D. N.

Edge

K. A.

Numerical simulation of fluid flow in poppet valves. Proc. IMechE, Part C: J. Mechanical Engineering Science, 1992, 206(2), 119–127. DOI: 10.1243/PIME_PROC_1992_206_105_02.

Johnston

D. N.

Edge

K. A.

Vaughan

N. D.

Experimental investigation of flow and force characteristics of hydraulic poppet and disc valves. Proc. IMechE, Part A: J. Power and Energy, 1991, 205(3), 161–171. DOI: 10.1243/PIME_PROC_1991_205_025_02.

Borghi

Milani

Paoluzzi

Transient flow force estimation on the pilot stage of a hydraulic valve. In Proceedings of the Winter Annual Meeting, American Society of Mechanical Engineers, Anaheim, CA, USA, November 1998, vol. 5, pp. 157–162 (ASME, New York).

Borghi

Cantore

Milani

Paoluzzi

Analysis of hydraulic components using computational fluid dynamics models. Proc. IMechE, Part C: J. Mechanical Engineering Science, 1998, 212(7), 619–629. DOI: 10.1243/0954406981521583

10.

Yang

Predicting hydraulic valve flow forces using CFD. In Proceedings of the ASME International Mechanical Congress and Exposition, Anaheim, CA, 13–19 November 2004, paper no. IMECE 2004-59719, pp. 55–61 (ASME, New York).

11.

McCloy

Martin

H. R.

Control of fluid power – analysis and design, edition 2, 1980 (Ellis Horwood Ltd, Chichester, UK).

12.

Roymech. Bolt preloading, 2009, available from http://www.roymech.co.uk/Useful_Tables/Screws/Preloading.html.