Systems optimisation of an active thermal management system during engine warm-up

Abstract

Active thermal management systems offer a potential for small improvements in fuel consumption that will contribute to upcoming legislation on carbon dioxide emissions. These systems offer new degrees of freedom for engine calibration; however, their full potential will only be exploited if a systems approach to their calibration is adopted, in conjunction with other engine controls. In this work, a design-of-experiments approach is extended to allow its application to transient drive cycles performed on a dynamic test stand. Experimental precision is of crucial importance in this technique since even small errors would obscure the effects of interest. The dynamic behaviour of the engine was represented mathematically in a manner that enabled conventional steady state modelling approaches to be employed in order to predict the thermal state of critical parts of the engine as a function of the actuator settings. A 17-point test matrix was undertaken, and subsequent modelling and optimisation procedures indicated potential 2–3% fuel consumption benefits under iso-nitrogen oxide conditions. Reductions in the thermal inertia appeared to be the most effective approach for reducing the engine warm-up time, which translated approximately to a 1.3% reduction in the fuel consumption per kilogram of coolant. A novel oil-cooled exhaust gas recirculation system showed the significant benefits of cooling the exhaust gases, thereby reducing the inlet gas temperature by 5 °C and subsequently the nitrogen oxide emissions by 6%, in addition to increasing the warm-up rate of the oil. This suggested that optimising the thermal management system for cooling the gases in the exhaust gas recirculation system can offer significant improvements. For the first time this paper presents a technique that allows simple predictive models of the thermal state of the engine to be integrated into the calibration process in order to deliver the optimum benefit. In particular, it is shown how the effect of the thermal management system on the nitrogen oxides can be traded off, by advancing the injection timing, to give significant improvements in the fuel consumption.

Keywords

Thermal management engine calibration design of experiments warm-up fuel consumption optimisation

Get full access to this article

View all access options for this article.

References

Delphi. Worldwide emissions standards: passenger cars and light duty vehicles, www.delphi.com/pdf/emissions/Delphi_PC.pdf (2010, accessed 6 June 2011).

Low carbon vehicles, driving the UK’s transport revolution. Report, Institution of Mechanical Engineers, London, UK, 2009.

Reducing CO₂ emissions from light-duty vehicles. European Commission, Brussels, Belgium, 2009.

Owen

Jackson

. A new look at the low carbon roadmap. In Low-carbon vehicles 2009. London: Chandos Publishing, 2009, pp.3–14.

Brace

Burnham-Slipper

Wijetunge

. Integrated cooling systems for passenger vehicles. SAE paper 2001-01-1248, 2001.

Burke

Brace

Hawley

Pegg

. Review of the systems analysis of the interactions of thermal, lubricant and combustion processes of diesel engines. Proc IMechE Part D: J Automobile Engineering 2010; 224(5): 681–704.

Chalgren

RDJ

. Thermal comfort and engine warm up optimization of a low flow advanced thermal management system. SAE paper 2004-01-0047, 2004.

Brace

Hawley

Akehurst

. Cooling system improvements – assessing the effects on emissions and fuel economy. Proc IMechE Part D: J Automobile Engineering 2008; 222(4): 579–591.

Tarquis

. Innovative engine cooling systems comparison. SAE paper 2005-01-1378, 2005.

10.

Burke

Brace

Cox

. Systems approach to the improvement of engine warm-up behaviour. Proc IMechE Part D: J Automobile Engineering 2011; 225(2): 190–205.

11.

Steinparzer

Unger

Bruner

Kannenberg

. The new BMW 2.0 litre 4-cylinder S.I. engine with twin power turbo technology. In: 32 Internationales Wiener Motorsymposium, Vienna, Austria, 5–6 May 2011, pp.57–72.

12.

Heiduk

Dornhofer

Eiser

. The new generation of the R4 TFSI engine from Audi. In: 32nd Internationales Wiener Motorsymposium, Vienna, Austria, 5–6 May 2011, pp.73–98.

13.

Andrews

Ounzain

. The use of a water/lube oil heat exchanger and enhanced cooling water heating to increase water and lube oil heating rates in passenger cars for reduced fuel consumption and CO₂ emissions during cold start. SAE paper 2007-01-2067, 2007.

14.

Kunze

Wolff

Lade

Tonhauser

. A systematic analysis of CO₂ reduction by an optimized heat supply during vehicle warm up. SAE paper 2006-01-1450, 2006.

15.

Burke

Brace

. The effects of engine thermal conditions on performance, emissions and fuel consumption. SAE paper 2010-01-0802, 2010.

16.

Lewis

Brace

Akehurst

Pegg

. Spatially resolved heat flux measurement from a HSDI engine over NEDC. In: International conference for vehicle thermal management systems, Gaydon, UK, 15–19 May 2011, pp.119–130.

17.

Burke

Brace

Hawley

. Critical analysis of on-engine fuel consumption measurement. Proc IMechE Part D: J Automobile Engineering 2011; 255(6): 829–844.

18.

Bannister

. Vehicle emissions measurement. PhD Thesis, Department of Mechanical Engineering, University of Bath, UK, 2007.

19.

Lewis

Brace

Cox

. The effect of forced cool down on cold start test repeatability. SAE paper 2009-01-1976, 2009.

20.

Torregrosa

Olmeda

Martin

Degraeuwe

. Experiments on the influence of inlet charge and coolant temperature on performance and emissions of a DI diesel engine. Expl Thermal Fluid Sci 2006; 30(7): 633–641.