The scope of this article is limited to the torsional driveline system of a front-engine front-wheel type of vehicle. A reduced-order model of a manual transmission (with the third gear engaged and the fifth gear unloaded) is developed on the basis of the modal characteristics. A simplified nonlinear mathematical model is then proposed with the focus on the multi-staged clutch damper properties such as the asymmetric transition angles and the pre-loads. The drag torque is estimated under two engine conditions (wide-open throttle and coast) by assuming that the vehicle is in the steady-state condition. Finally, the gear rattle criteria are investigated, and illustrative examples for three real-life clutch dampers are described. In particular, methods for solving the real-life gear rattle phenomenon are suggested.
ChikataniYSuehiroA. Reduction of idling rattle noise in trucks. SAE paper 911044, 1991.
3.
HowellTPPowellNNEtheridgeP. The application of correlated modeling techniques to investigate gear rattle noise in a Harley–Davidson motorcycle. In: 31st international congress and exposition on noise control engineering, Dearborn, Michigan, USA, 19–21 August 2002, pp. 2469–2477. Ashland, Ohio: Atlas Books.
4.
ShimizuT. Mechanism of the idle gear rattle synchronized with engine rotation. SAE paper 932003, 1993.
5.
LaschetA. Computer simulation of vibration in vehicle powertrains considering nonlinear effects in clutches and manual transmissions. SAE paper 941011, 1994.
6.
FanJHierlwimmerPLaschetA. Investigation of gear rattle sensitivity on manual transmissions in the target setting process. ATZ Automobiltechnische Z1997; 99(5): 9–11.
7.
PadmanabhanCRookTESinghR. Modeling of automotive gear rattle phenomenon: state of the art. SAE paper 951316, 1995.
8.
PadmanabhanCSinghR. Influence of clutch design on the reduction and perception of automotive transmission rattle noise. In: 1993 national conference on noise control engineering, Williamsburg, Virginia, 2–5 May 1993, pp. 607–612. Poughkeepsie, New York: Noise Control Foundation.
9.
BarthodMHayneBTébecJLPinJC. Experimental study of gear rattle excited by a multi-harmonic excitation. Appl Acoust2007; 68: 1003–1025.
10.
WangMYZhaoWManojR. Numerical modeling and analysis of automotive transmission rattle. J Vibr Control2002; 8: 921–943.
11.
ShimSBParkYJKimKU. Reduction of PTO rattle noise of an agricultural tractor using an anti-backlash gear. Biosystems Engng2008; 100: 346–354.
12.
RoccaERussoR. Theoretical and experimental investigation into the influence of the periodic backlash fluctuations on the gear rattle. J Sound Vibr2011; 330: 4738–4752.
13.
KaragiannisKPfeifferF. Theoretical and experimental investigations of gear-rattling. Nonlinear Dynamics1991; 2: 367–387.
14.
BozcaMFietkauP. Empirical model based optimization of gear box geometric design parameters to reduce rattle noise in an automotive transmission. Mech Mach Theory2010; 45: 1599–1612.
BellomoPDe VitoNLangCScamardiL. In depth study of vehicle powertrains to identify causes of loose components rattle in transmissions. SAE paper 2002-01-0702, 2002.
17.
FujimotoTKizukaT. Predictive calculation of idling rattle in manual transmissions. SAE paper 2003-01-0678, 2003.
18.
De la CruzMTheodossiadesSRahnejatH. An investigation of manual transmission drive rattle. Proc IMechE Part K: J Multibody Dynamics2010; 224(2): 167–181.
19.
YakoubRCorradoMForcelliAPappalardoTDutreS. Prediction of system-level gear rattle using multibody and vibro acoustic techniques. SAE paper 2004-32-0063, 2004.
20.
NovakWKieferSBertscheBStockheimerMRyborzJDoganS. Noise reduction and efficiency improvements via clatter and rattle noise free (CARF-) transmissions. Proc IMechE Part K: J Multibody Dynamics2007; 221(K3): 363.
21.
GnanakumarrMTheodossiadesSRahnejatH. The tribo-contact dynamics phenomenon in torsional impact of loose gears – promoting gear rattle. SAE paper 2002-01-2249, 2002.
22.
PadmanabhanCSinghR. Spectral coupling issues in a two-degree-of-freedom system with clearance non-linearities. J Sound Vibr1992; 155(2): 209–230.
ComparinRJSinghR. Non-linear frequency response characteristics of an impact pair. J Sound Vibr1989; 134(2): 259–290.
25.
ComparinRJSinghR. Frequency response characteristics of a multi-degree-of-freedom system with clearance. J Sound Vibr1990; 142(1): 101–124.
26.
PadmanabhanCSinghR. Dynamics of a piecewise non-linear system subject to dual harmonic excitation using parametric continuation. J Sound Vibr1995; 184(5): 767–799.
27.
KimTCSinghR. Dynamic interactions between loaded and unloaded gears. SAE paper 2001-01-1553, 2001.
28.
KimTCRookTESinghR. Super- and sub-harmonic response calculation for a torsional system with clearance nonlinearity using the harmonic balance method. J. Sound Vibr2005; 281: 965–993.
29.
KimTCRookTESinghR. Effect of nonlinear impact damping on the frequency response of a torsional system with clearance. J Sound Vibr2005; 281: 995–1021.
30.
KimTCRookTESinghR. Effect of smoothening functions on the frequency response of an oscillator with clearance non-linearity. J Sound Vibr2003; 263: 665–678.
31.
RookTESinghR. Dynamic analysis of a reverse-idler gear pair with concurrent clearance. J Sound Vibr1995; 182(2): 303–322.
32.
PadmanabhanCSinghR. Analysis of periodically excited non-linear systems by a parametric continuation technique. J Sound Vibr1995; 184(1): 35–58.
33.
TrochonEP. Analytical formulation of automotive drivetrain rattle problems. MS Thesis, The Ohio State University, Columbus, Ohio, USA, 1997.
YoonJY. Effect of multi-staged clutch damper characteristics on vibro-impacts within a geared system. MS Thesis, The Ohio State University, Columbus, Ohio, USA, 2003.
36.
Den HartogJP. Mechanical vibrations. New York: Dover Publications, 1985.
37.
DormandJRPrincePJ. A family of embedded Runge–Kutta formulae. J Comput Appl Math1980; 6(1): 19–26.
38.
YoonJYSinghR. Dynamic force transmitted by hydraulic mount: estimation in frequency domain using motion and/or pressure measurements and quasi-linear models. Noise Control Engng J2010; 58(4): 403–419.
39.
PacejkaHB. Tyre and vehicle dynamics. Oxford: Elsevier, 2002.
National Science Foundation, Directorate for Engineering. Industry & University Cooperative Research Program (I/UCRC), www.nsf.gov/eng/iip/iucrc (accessed July 2007).
